Jason.L ST SUPREME E23T User manual

ASSEMBLY INSTRUCTION
MODEL : ST SUPREME E23T
Electric Straight Desk Frame
(1200mm - 1800mm Length)
V1.2

Component List - ST SUPREME E23T_V1.2
AR
Axle Drive L400mm
Qty : 2
Hex Shaft L250mm
Qty : 3
Screw M5 X L10
Qty : 14
Left Column
Qty:1
Crossbar Motor Model
Qty : 1
Cable Tray
Qty : 1
Right Column
Qty: 1
Crossbar Assy. Left
Qty: 1
Screw M6XL10
Qty : 3
Leveling Base
Qty: 4
Control Box
TC11
Qty : 1
Motor
TGM1-2252-003
Qty : 1
Handset TH14
Qty : 1
Rubber Type-A
Qty: 10
Crossbar Assy. Right
Qty: 1
Axle Drive L550mm
Qty : 2
Side L Plate
Qty: 2
Screw M6 X L16
Qty : 8
Hex Shaft L100mm
Qty : 2
3mm
4mm
5mm
23
RHD Woodscrew
M5X25
Qty: 10
CSK Woodscrew
M4X30
Qty: 2
22
NIL
Foot
Qty: 2
01 02 03
04
05
06
07
08
09
10
11
12
13 14 15 16 17 18
19 20 21

V1.2 Pg.1/12
04
03
17
17
01
15
15
15
15
Marking 'L' column
direction must be follow
13
13
13
13
STEP 2 : Install Foot
STEP 3 : Install Crossbar Left Assy.
Step 1 : Install Leveling Base
ITEM NO. DESCRIPTION QTY.
03 Foot 1
17 Leveling Base 2
ITEM NO. DESCRIPTION QTY.
01 Left Column 1
15 Screw M6 XL16 4
ITEM NO. DESCRIPTION QTY.
04 Crossbar Assy. Left 1
13 Screw M5 XL10 4
Assembly Instruction: Left Stand Assembly

V1.2 Pg.2/12
05
03
17
17
02
15
15 15
15
13
13
13
13
Marking 'R' column
direction must be follow
STEP 2 : Install Foot
STEP 3 : Install Crossbar Right Assy.
Step 1 : Install Leveling Base
ITEM NO. DESCRIPTION QTY.
03 Foot 1
17 Leveling Base 2
ITEM NO. DESCRIPTION QTY.
02 Right Column 1
15 Screw M6 XL16 4
ITEM NO. DESCRIPTION QTY.
05 Crossbar Assy. Right 1
13 Screw M5 XL10 4
Assembly Instruction: Right Stand Assembly

07
Set Screw M6
(X4)
V1.2 Pg.3/12
Notes :
1.Please follow arrow left and right direction to
adjust the frame length fixed table top size.
2.Tighten set screw M6(X4) after fixed frame length.
(Recommended length 115cm,145cm,175cm)
ITEM NO. DESCRIPTION QTY.
07 Crossbar Motor Model 1
Assembly Instruction: Integrate Left & Right Stand

18
14
14
14
V1.2 Pg.4/12
ITEM NO. DESCRIPTION QTY.
14 Screw M6 XL10 3
18 Motor TGM1-2252-003 1
Assembly Instruction: Install Motor Assembly

For Length 115cm
10
10
11
PRESS DOWN
PRESS DOWN
08
08
Remarks; Lock Bush
Item No. 08 (Axle Drive L400mm)
Lock Bush (X4) dismantle from
Item No. 09 (Axle Drive L550mm)
Set Screw M6(x4)
CJ
(50~60) (50~60)
Figure No.1
Notes:
1.Before Insert Hex Shaft, make sure
Left Stand & Right Stand are at lowest position.
Please see attachment caution ! (Refer Pg8/12.)
2. After insert Hex Shaft
10
and Axle Drive
08
align according as per Figure No.1
dimension.
3. Locking Set Screw M6 (x4)
V1.2 Pg.5/12
ITEM NO. DESCRIPTION QTY.
08 Axle Drive L400mm 2
10 Hex Shaft L100mm 2
11 Hex Shaft L250mm 1
Assembly Instruction: Axle Drive And Hex Shaft Assy.

For Length 145cm
10
10
11
PRESS DOWN
PRESS DOWN
09
09
CK
(50~60) (50~60)
Figure No.2
Set Screw M6(x4)
Notes:
1.Before Insert Hex Shaft, make sure
Left Stand & Right Stand are at lowest position.
Please see attachment caution ! (Refer Pg8/12).
2. After insert Hex Shaft
10
and Axle Drive
09
align according as per Figure No.2
dimension.
3. Locking Set Screw M6 (x4)
V1.2 Pg.6/12
ITEM NO. DESCRIPTION QTY.
09 Axle Drive L550mm 2
10 Hex Shaft L100mm 2
11 Hex Shaft L250mm 1
Assembly Instruction: Axle Drive And Hex Shaft Assy.

For Length 175cm
11
11
11
PRESS DOWN
PRESS DOWN
09
09
CK
(50~60) (50~60)
Figure No.3
Set Screw M6(x4)
Notes:
1.Before Insert Hex Shaft, make sure
Left Stand & Right Stand are at lowest position.
Please see attachment caution ! (Refer Pg8/12).
2. After insert Hex Shaft
11
and Axle Drive
09
align according as per Figure No.3
dimension.
3. Locking Set Screw M6 (x4)
V1.2 Pg.7/12
ITEM NO. DESCRIPTION QTY.
09 Axle Drive L550mm 2
11 Hex Shaft L250mm 3
Assembly Instruction: Axle Drive And Hex Shaft Assy.

AW
BC
BR
16
BN
16
BP
Press down the column make sure it is at lowest postion.
The marking O not appear means it is at lowest position
refer to below diagram.
Marking
fully seen
Marking
partially seen
Marking not seen
(Means at lowest position)
Press
Press
V1.2 Pg.8/12
Caution: Column Must Be At Lowest Position Before Install Hex Shaft

06
06
13
13
13
13
V1.2 Pg.9/12
ITEM NO. DESCRIPTION QTY.
06 Side L Plate 2
13 Screw M5 XL10 4
Assembly Instruction: Install Side L Plate

13
Install Control Box & Handset
Install Cable Tray
12
13
19
20
Notes :
Step 1: Install Cable Tray
12
Step 2: Lock with screw M5
13
(x2)
Notes :
Step 1: Place Control Box
19
to Cable Tray
12
Step 2: Plug Motor connector and Handset
connector
20
to control box
19
V1.2 Pg.10/12
ITEM NO. DESCRIPTION QTY.
12 Cable Tray 1
13 Screw M5 XL10 2
ITEM NO. DESCRIPTION QTY.
19 Control Box TC11 1
20 Handset TH14 1
Assembly Instruction: Install Cable Tray & Control Box & Handset

16
16
16
16 16
16
16
16
16
16
Figure No.4
V1.2 Pg.11/12
ITEM NO. DESCRIPTION QTY.
16 Rubber Type-A 10
Assembly Instruction: Plug Rubber Type-A

'DOWN BUTTON'
'UP BUTTON'
V1.2 Pg.12/12
Caution!
Duty cycle: Max. 2min ON / 18 min OFF.
Reset operation as below :
1. Initial reset
For the first powered up, press and hold both 'UP' and 'DOWN' buttons
simultaneously for more than 3 seconds until the desk moves down to lowest
position.
After checking the signal motor constant, reset was completed and ready to
use.
*The initialization procedure must be completed before the first running after
the table is installed or parts are replaced.*
2. Any dismantle of mechanism or electrical component follow below procedure.
Follow procedure no.1 again.
Caution!
Make sure all cable are connected to control box before power up.
Assembly Instruction: Reset The Desk Before Use