Javo Traytopper User manual

User Manual
Original document
version 2016-2
Traytopper
Javo BV
Postbus 21
2210 AA Noordwijkerhout
Holland
T: [phone]
F: [phone]
[email protected]
www.javo.eu
© All rights reserved
The information provided herein may not be reproduced and/or published in any form, by print, photo print, microfilm or any other means
whatsoever (electronically or mechanically) without the prior written authorisation of JAVO BV.

User Manual Javo Traytopper
Version 2016-2 1
Preface
This user manual is written for anyone working on or with the machine. Before working on or with the machine, first
read this manual.
This user manual contains important instructions / information on how to use the machine in a safe, professional
and economical way and must always be available where the machine is used.
In addition to this user manual, the mandatory rules and regulations for accident prevention and environmental
protection in the country and place of use of the machine must also be observed.
This user manual contains information on the operation of the machine with all the possible options. Use only the
information that applies to your machine. Depending on the intensity of use and customer requirements, this
machine can be equipped with various options. Contact your sales consultant.
Supplier details if not directly supplied by Javo
BV. Dealer stamp:
Javo BV is not responsible for any errors in this manual or the consequences thereof.
Javo BV is not liable for damage or consequential damage caused by operating errors, lack of expert maintenance and any use other than
described in this manual.
The liability of Javo BV also expires once modifications or additions are made without written permission of Javo BV.
This machine is suitable for process and environmental conditions as stated in section "Specifications and Tolerances" of this manual. Any
other use is not authorized by Javo BV and this allows the operator and / or its environment at risk.

User Manual Javo Traytopper
Version 2016-2 2
Table of contents
1Technical specifications and tolerances .........................................................................................................4
1.1 Type plate.......................................................................................................................................................... 4
2Safety...........................................................................................................................................................5
2.1 Provisions .......................................................................................................................................................... 5
2.2 Safety devices on the machine ......................................................................................................................... 6
2.3 Explanation of icons and symbols..................................................................................................................... 6
3Description of the machine ...........................................................................................................................7
3.1 Machine overview............................................................................................................................................ 7
3.2 Outline drawing with main dimensions ............................................................................................................ 7
3.3 Options.............................................................................................................................................................. 8
3.4 Operation .......................................................................................................................................................... 8
3.5 Machine workstations....................................................................................................................................... 8
3.6 Controls............................................................................................................................................................. 9
4Transport ................................................................................................................................................... 10
5Mounting, installation and commissioning .................................................................................................. 11
5.1 Placement .......................................................................................................................................................11
5.2 Facilities to take care of by the user .............................................................................................................11
5.3 Mounting / Connecting ................................................................................................................................... 11
5.4 Check rotation direction .................................................................................................................................11
5.5 Check substrate conveyor tension.................................................................................................................. 12
5.6 Check spreading conveyor tension ................................................................................................................. 12
5.7 Check elevator chain tension..........................................................................................................................12
5.8 Set substrate conveyor speed.........................................................................................................................13
5.9 Set substrate slide...........................................................................................................................................13
5.10 Set spreading pilots......................................................................................................................................... 13
5.11 Set spreading quantity .................................................................................................................................... 13
6Operation................................................................................................................................................... 14
6.1 Start.................................................................................................................................................................14
6.2 Stop ................................................................................................................................................................. 14
6.3 Emergency stop.............................................................................................................................................. 14
7Maintenance .............................................................................................................................................. 15
7.1 Required tools and equipment .......................................................................................................................15
7.2 Preventive Maintenance................................................................................................................................. 15
7.3 Elevator cleaning............................................................................................................................................. 16
7.4 Test safety circuit ............................................................................................................................................16
7.5 Fault list........................................................................................................................................................... 16
7.6 Drawings and schemes.................................................................................................................................... 17
7.7 Spare parts ...................................................................................................................................................... 17

User Manual Javo Traytopper
Version 2016-2 3
7.8 JavoNet............................................................................................................................................................17
7.9 Customer support and advice......................................................................................................................... 17
8Disposal of machine or machine parts ......................................................................................................... 17
9EG-conformity statement............................................................................................................................ 18

User Manual Javo Traytopper
Version 2016-2 4
1Technical specifications and tolerances
This machine is intended to be used for filling trays automatically with substrate only. This machine is meant for
processing trays, substrate and other materials that are described in this manual only. Detailed operation of the
machine is described in section "Operation".
This machine may be used only within the limits for specifications and tolerances of the order, on the
assembly drawing and indicated in this manual. If the machine is used outside these specifications, Javo BV
can not take responsibility for this machine.
This machine is intended for products as agreed in the order confirmation only. To ensure the proper
operation of this machine, only products with specifications and tolerances as specified in the order may be
used.
Do not use the machine for purposes other than the intended purpose of Javo BV. This can lead to damage
and danger to the operator and its environment.
This machine is CE marked. When placing multiple machines in one line, the entire line must be properly CE
marked before using this machine. Untill proper CE Marking of the line is carried out, commissioning of this
machine is prohibited.
Specifications
Voltage
400Volt 50Hz 3~+N+ PE (or in consultation)
Machine connection
16A 5pole
Power consumption
1.5 kW
Measurements (length X width X height)
3650 X 1300 X 2500 mm
Weight
520kg
Height conveyor
840 mm
Work direction
From left to right
Max. speed
540 m. p/u bij 60Hz
Min. speed
126,5 m. p/u bij 12,5 Hz
Minimum passage height
190mm
Maximum passage height
230mm
Maximum tray width
470mm
Content substrate bin
770 Litre
Drive conveyor
Motor on frequency drive (controls on electrical cabinet)
Tray conduction 2 sides
Adjustable in width
Substrate slide in substrate bin
Standard
Year of construction
See type plate
Type product
As agreed in the order confirmation.
1.1 Type plate
The type plate is placed onto the main cabinet door.

User Manual Javo Traytopper
Version 2016-2 5
2Safety
This machine is built according the state of the art technique and the accredited safety regulations. Despite
this, the body and life from the user or third parties can be in danger when using it. There could also arise
damage to the machine or other goods when using it.
This machine is CE marked. When placing multiple machines in one line, the entire line must be properly CE
marked before using this machine. until proper CE Marking of the line is carried out, commissioning of this
machine is prohibited.
2.1 Provisions
1. Operation and maintenance of this machine must be performed by qualified personnel in compliance with
warnings on the machine and in accordance with the user manual. Keep children and other (unauthorized)
persons away while using machine.
2. This machine is suitable for process and environmental conditions as stated in section "Specifications and
Tolerances" of this manual only. Any other use is not authorized by Javo BV and this allows the operator and /
or the environment at risk.
3. It is prohibited to modify this machine, without prior written approval of Javo BV.
4. Thermal fuses and torque limiters may not be set different upon delivery of the new machine. The thermal
circuit breakers should never be used to turn on / off the machine.
5. This machine should be installed so that there is sufficient space remaining for providing safe instructions and /
or performing maintenance and / or inspections. Put the brakes on the castors before the machine is turned on.
6. Keep the work area clean and well lit. Cluttered or dark areas invite accidents.
7. This machine is not suitable to be used outside. Electrical components are only splash proof. Keep the machine
away from rain and moisture. When using the machine in a humid environment is unavoidable, you should use
an RCD.
8. Keep hands, hair, loose clothing and / or jewellery away from moving parts of the machine. Wear appropriate
clothing without loose parts. Wear non-slip work shoes.
9. As long as the machine is on, no connection or safety devices may be removed. The machine may only be used
when all protective devices and safety-related facilities are available and ready for use.
10. Do not stand on the machine when it is operating.
11. Never move the machine if the power cable and / or pneumatic supply is still connected.
12. Prescribed checks and maintenance in the user manual must be observed.
13. Allow the machine to be serviced and repaired by qualified personnel only with original replacement parts.
14. In addition to the user manual, generally applicable statutory and other regulations regarding accident
prevention and environmental protection have to be respected. This is also referred to handling of personal
protective equipment.
15. Inform operating personnel before start maintenance. Interrupt if possible the power (mains), before start
machine investigation or maintenance by turning off the main switch and locking the main switch. Pull the plug
from the wall socket.
a. As work must be done with power supply (mains) voltage on the machine, then arrange an
additional person who can operate the emergency stop.
16. When a machine part is damaged or not working in the prescribed manner, the work must be interrupted
immediately. Resumption allowed only when the machine part is repaired or replaced and checked. Consult
your dealer if the machine is not functioning properly.
17. Machine and / or parts must be disposed in accordance with local laws and regulations.

User Manual Javo Traytopper
Version 2016-2 6
2.2 Safety devices on the machine
Caps and doors are screening moving parts. Always place back caps and close doors before the machine is
turned on. Caps and doors should remain closed while operating the machine.
The motors of the machine are protected against overload by thermal switches. These switches are located in the
control box.
2.3 Explanation of icons and symbols
Pictogram
Meaning
Read and understand this manual before using the machine and / or performing maintenance.
Remove Power (mains).
Wear during all work on or with the machine safety shoes and safety glasses.
Wear during cleaning and maintenance work on this machine also safety gloves and protective
clothing.
Warning.
Important points and / or instructions regarding safety and / or injury prevention are marked with
this warning sign.
Dangerous electrical voltage.
Dangerous electrical voltage present.
Risk of crushing.
Danger of moving or rotating parts.
It is forbidden to wear Loose clothing, long hair and / or jewelry nearby moving parts of the
machine.
Trespassing.
Do not rinse control cabinet
Danger of moisture in the cabinet when it is rinsed with water.
Symbols that may be present on this machine
Drill
Direction of movement
Speed ground feeder
(curved)
Speed ground feeder
(straight)
Elevator standard
Elevator SE
Pot
Tray belt Rotofill
Speed pot belt (curved)
Speed pot belt (straight)
Brush disc Rotofill
Rotor Rotofill

User Manual Javo Traytopper
Version 2016-2 7
3Description of the machine
3.1 Machine overview
A. Elevator
B. Pour Funnel
C. Spreading conveyor
D. Pilots
E. Conveyor with trays to be spreaded (option)
F. Substrate slide
G. Substrate bin
H. Substrate conveyor
3.2 Outline drawing with main
dimensions
A
B
C
D
E
F
G
H

User Manual Javo Traytopper
Version 2016-2 8
3.3 Options
Depending on the intensity of use and customer requirements, this machine can be equipped with various options.
Contact your sales consultant.
Options
Code
Specifications
4 meter 5x1.5 cable incl. 16A plug
900965
Continuous socket
900966
Nonstandard
Substrate bin increasement
276-700
Air wheels front
SU1L
3.4 Operation
The process of the machine begins at the soil bin, which is filled with substrate. Substrate is transported with the
substrate conveyor to the elevator.
The elevator takes over substrate and puts it into the hopper. A capacitive sensor measures the level of the
spreading substrate in the hopper. A spreading conveyor is located at the bottom of the hopper which spreads
substrate or pebbles on trays if there is passing by trays. The pilots guide the excess substrate back to the substrate
bin. Trays are transported on a separate conveyor belt below the spreading conveyor.
The width is adjustable for different trays, so the machine can be used for different tray sizes.
The machine is equipped with wheels, which makes the machine easy to move.
3.5 Machine workstations
This machine has two operator places; at the conveyor belt, both the inlet and the outlet on the side of the substrate
bin.

User Manual Javo Traytopper
Version 2016-2 9
3.6 Controls
The motor is controlled with the control panel. This control panel is flexible around the machine to be used by
means of a cable. The control panel consists of the following buttons;
A. Stop button
B. Start button
C. Reset button
D. Emergency stop button
At the electrical cabinet of the machine, these buttons and
connectors are placed:
A. Stopped error
B. Main switch
C. Start
D. Stop
E. Elevator off /on
F. Spreading conveyor off /on
G. Reset
H. Speed spreading belt
a. (optional extra potentiometers will be for the
charge and discharge conveyor)
The machine is equipped with emergency stop buttons:
I. Emergency stop button
A
B
C
D
A
B
C
D
F
G
H
E
I