JBL CS6100 User manual

Cinema Sound
CS100
CS6100 Amplifier/Subwoofer
SERVICE MANUAL
JBL Consumer Products
250 Crossways Park Dr.
Woodbury, New York 11797 Rev1 3/2008

Note: The CS100 subwoofer is part of the CS6100 system
Satellite loudspeakers CS6100 order JBL part# CS600SATBG-E
Center channel CS6100 order JBL part# CS600CENBG-E
- CONTENTS -
BASIC SPECIFICATIONS……………….….….….….…………….1
DETAILED SPECIFICATIONS ……..…………….……………..2
PACKAGING……………………………………….........................4
CONTROLS & CONNECTIONS.………………………………….5
OPERATION ………….……………………………..…………….6
EXPLODED VIEW/PARTS LIST…………………………………..7
TEST SET-UP AND PROCEDURE……..…………….………….8
BLOCK DIAGRAM..…………………………………………………9
BASIC TROUBLESHOOTING…..…………….…..…..….……...10
120V ELECTRICAL PARTS LIST ……………………………….11
PCB DRAWINGS………………..………………………………...15
INTEGRATED CIRCUIT/TRANSISTOR PINOUTS…………..19
120V SCHEMATICS.……….……………….………..…. ………20
BASIC SPECIFICATIONS
CS100 Subwoofer
Frequency Response (– 6dB): 30Hz – 120Hz
Amplifier Output: 150W RMS/300W Peak†
Driver: 10" (254mm)
Dimensions (H x W x D, including feet): 18-1/2" x 12-3/4" x 15" (470mm x 324mm x 381mm)
Weight: 41 lb (18.6kg)
† The Peak Dynamic Power is measured by recording the highest center-to-peak voltage measured across the output of a
resistive load equal to minimum impedance of the transducer, using a 50Hz sine wave burst, 3 cycles on, 17 cycles off.
Occasional refinements may be made to existing products without notice but will always meet or exceed original
specifications unless otherwise stated
CS100(CS6100Subwoofer)
1

CS100SUB 150W Powered Sub/ Plate Amp
LINE VOLTAGE Yes/No Hi/Lo Line Unit Notes
US 120vac/60Hz Yes 108-132 Vrms Normal Operation
EU 230vac/50-60Hz Yes 207-264 Vrms Normal operation, MOMS required
Parameter Specification Unit QA Test Limits Conditions Notes
Amp Section
Type (Class AB, D, other) D D n/a
Load Impedance (speaker) 4 Ohms n/a Nominal
Rated Output Power 150 Watts 145 1 input driven
THD@ Rated Power 0.08 % 1 22K filter
THD @ 1 Watt 0.1 % 0.5 22K filter
DC Offset 10 mV-DC 20 @ Amplifier Output
Damping factor >100 N/A 15 50Hz-4 Ohms load
Measured at amplifier PCB speaker out
connector @ 135 Watts into rated
impedance.
Input Sensitivity
Input Frequency 50 Hz 50 Nominal Freq. 1 input driven
Line Input (L&R) 19.42 mVrms ±2dB To 1 Watt 1 input driven
LFE Input 10.2 mVrms ±2dB To 1 Watt LFE input driven only
Line Input (L & R) Gain 40.25 dB ±1dB 1 input driven
LFE Input Gain 45.84 dB ±1dB LFE input driven only
Signal to Noise
SNR-A-Weighted 100 dBA 85 rel. to rated power A-Weighting filter
SNR-Un-weighted 90 dBr 80 rel. to rated power 22K filter
SNR @ 1W-Un-weighted 60 dBr 60 rel. to 1W Output 22K filter
Residual Noise Floor 1 mVrms 2 Volume @max, using RMS reading
DMM/VOM (or A/P)
Residual Noise Floor 1 mVrms(max) 2Volume @max, w/ A/P Swept Bandpass
Measurement (Line freq.+ harmonics)
Input Impedance
Line input L&R , LFE >10 K ohms n/a Nominal
Filters
Left & Right Low Pass fixed Hz -- ±2dB
Order & Q 4th dB/Octave n/a
LFE Low Pass fixed Hz -- ±2dB
Order & Q 2nd dB/Octave n/a
Subsonic filter (HPF) Hz -- ±2dB
Order & Q 2nd dB/Octave n/a
Limite
r
(yes/no) YES -- n/a
Features
LFE Input YES Functional BW limited to 500 Hz, refer to ECR00031
Phase Switch (yes/no) YES -- Functional
Volume pot Taper
(
linear/lo
g
LOG -- Functional
ATO (Auto-ON) YES Functional
Input Configuration
Line In (L,R) L ,R -- Functional RCA inputs: L , R
Line level in LFE LFE Functional
Signal Sensing (ATO)
ATO test Frequency 50 Hz
ATO Line Level 2 mV Functional 2mV@50Hz into Line Input w/ 1 ch.
driven
ATO Turn-on time 5 ms Functional Amp connected and AC on, then input
signal applied in excess of 2mV applied
Auto Mute/ Turn-OFF Time 15 minutes Functional T before muting, after signal is removed
A
uto turn off time
(
T
)
must be
5min > T <15min
Power on Delay time 3 sec. Functional AC Power Applied
Transients/Pops
ATO Transient 5 mV-peak 10 @ Speaker Outputs
Turn-on Transient 50 mV-peak 100 @ Speaker Outputs AC Line cycled from OFF to ON
Turn-off Transient 50 mV-peak 100 @ Speaker Outputs AC Line cycled from ON to OFF
CS100(CS6100Subwoofer)
2

Parameter Specification Unit QA Test Limits Conditions Notes
Efficiency
Stand-by Input Power 12 Watts 16 @ nom. line voltage
Maximum allowable input power under
nominal Input voltage and frequency, HOT
or COLD operation.
Power Cons.@rated power 250 Watts 250 @ nom. line voltage 150 Watts @ 4 Ohms nominal line voltage
Efficiency >60 % >60 @ nom. line voltage 150 Watts @ 4 Ohms nominal line voltage
Protection
Short Circuit Protection YES -- Functional Direct short at output
Thermal Protection 65 deg. C -- Functional @1/8 max unclipped Power Back panel temperature rise should not
exceed 35K rise.
DC Offset Protection YES -- Functional DC present at Speaker Out leads Relay or crowbar (for driver/fire protection)
AC Line Fuse Rating
120VAC 3.15 Amps Type-T or Slo Blo, Fuse markings
T3.15A, 250V External fuse with UL/SEMKO rated holder
230VAC 1.6 Amps Type -T, Low breaking capacity,
Fuse markings T1.6AL, 250V External fuse with UL/SEMKO rated holder
CS100(CS6100Subwoofer)
3

CS100(CS6100Subwoofer)
PACKAGING
4

SUBWOOFER CONTROLS
Rear Panel
1Phase Switch
2LFE Input
3Line-Level Inputs
4Power Indicator LED
5Subwoofer-Level Control
6Power Switch
Subwoofer Connections
If you have a Dolby®Digital or DTS®receiver/processor with a
low-frequency-effects (LFE) or subwoofer output:
§
RISK O F ELEC TRICSHOCK
DO NOTOPEN
CAUTION
RISK O F ELEC TRICSHOCK
DO NOTOPEN
CAUTION
RISK O F ELEC TRICSHOCK
DO NOTOPEN
CS100SUB/230
POWER
T 1.6AL/250V
"W ARNING :FO R C O N TINUED
PRO TECTION AGAINST RISK
OFFIRE,REPLACE ONLY W ITH
SAM E TYPE T 1.6A L/250V FU S E "
"AVERTISSEM ENT:UTILISEZ UN
FUSIBLE DE RECHAN G E DE M EM E
TYPE T 1.6A L/250V "
AC 220V -230V
50Hz-60Hz
250 W atts
SUBWOOFER OR
LFE OUTPUT
RECEIVER/PROCESSOR
15' (4.5m)
Subwoofer cable
included
If your receiver/processor does not contain a Dolby Digital or DTS
processor but has a subwoofer output:
NOTE :If your receiver/processor has only one sub out, you may use
either the L or R input.
15' (4.5m)
Subwoofer cable
included
§
RISK O F ELECTRICSHOCK
DO NOT OPEN
CAUTION
RISK O F ELECTRICSHOCK
DO NOT OPEN
CAUTION
RISK O F ELECTRICSHOCK
DO NOT OPEN
CS100SUB/230
POWER
T 1.6AL/250V
"W ARNING :FO R C O N TINUED
PRO TECTION AGAINST RISK
OF FIRE,REPLACE ONLY W ITH
SAM E TYPE T 1.6A L/250V F U S E "
"AVERTISSEM EN T:UTILISEZ UN
FU SIBLE DE RECHAN G E DE M EME
TYPE T 1.6A L/250V "
AC 220V-230V
50Hz-60Hz
250 W atts
RECEIVER/PROCESSOR
Important!
Whenever changing cables, pulling plugs, etc., ALWAYS TURN OFF
ALL EQUIPMENT,including the subwoofer.
CS6100-120V om.qxd 12/15/06 4:26 PM Page 10
CS100(CS6100Subwoofer)
5

OPERATION
Surround Modes
When using the CS6100 speakers in a Dolby Digital or DTS home
theater system, make sure all speakers are set to “Small”. In a
Dolby Pro Logic®home theater system, make sure the receiver’s
center channel mode is set to “Normal.”
Some Dolby Digital-equipped receivers/processors offer different
setup options for each source or surround mode (e.g., CD-stereo,
videotape, Dolby, Pro Logic). In each case, follow your equipment’s
instructions to ensure that the subwoofer output is turned on and
that the speakers are set to “Small” in each mode.
Power On
Plug your subwoofer’s AC cord into a wall outlet. Do not use the outlets
on the back of the receiver.
Initially set the Subwoofer-Level Control 5to the“MIN” position.
Turn on the subwoofer by pressing the Power Switch 6on the
rear panel.
Turn on your entire audio system and start a CD or movie soundtrack
at a moderate level.
Auto On/Standby
With the Power Switch 6in the ON position, the LED on the rear
panel 4will remain lit in green or red to indicate the ON or STANDBY
mode of the subwoofer.
RED = STANDBY (No signal detected, Amp Off)
GREEN = ON (Signal detected, Amp On)
The subwoofer will automatically enter the Standby mode after
approximately 10 minutes when no signal is detected from your
system. The subwoofer will then power on instantly when a signal
is detected. During periods of normal use, the Power Switch 6
can be left on. You may turn off the Power Switch 6for extended
periods of nonoperation, e.g., when you are away on vacation.
Adjust Level
Turn the Subwoofer-Level Control 5up about halfway.If no sound
emanates from the subwoofer, check the AC-line cord and input
cables. Are the connectors on the cables making proper contact? Is
the AC plug connected to a “live” receptacle? Has the Power Switch
6been pressed to the ON position? Once you have confirmed that
the subwoofer is active, proceed by playing a CD or DVD. Use a
selection that has ample bass information.
Set the overall volume control of the receiver/processor to a
comfortable level. Adjust the Subwoofer-Level Control 5until you
obtain a pleasing blend of bass. Bass response should not overpower
the room but rather be adjusted so there is a harmonious blend
across the entire musical range. Many users have a tendency to
set the subwoofer volume too loud, adhering to the belief that a
subwoofer is there to produce lots of bass. This is not entirely true.
Asubwoofer is there to enhance bass, extending the response of
the entire system so the bass can be felt as well as heard. However,
overall balance must be maintained or the music will not sound
natural. An experienced listener will set the volume of the subwoofer
so its impact on bass response is always there but never obtrusive.
Phase Control
The Phase Switch 1determines whether the subwoofer speaker’s
pistonlike action moves in and out with the main speakers (0˚) or
opposite the main speakers (180˚). Proper phase adjustment depends
on several variables such as room size, subwoofer placement and
listener position. Adjust the phase switch to maximize bass output
at the listening position.
9
CS6100-120V om.qxd 12/15/06 4:26 PM Page 11
CS100(CS6100Subwoofer)
6

CS100(CS6100Subwoofer)
EXPLODED VIEW
7

CS100 Test Set Up and Procedure
Equipment needed:
•Function/signal generator/sweep generator
•Integrated Amplifier
•Multimeter
•Speaker cables
General Unit Function (UUT = Unit Under Test)
1) From the signal generator, connect one line level (RCA) cable to the Subwoofer Line Level Input jacks L/R
on the UUT. Use a Y-cable from a mono source if necessary to connect to both inputs. Do not connect to
the single LFE input.
2) Turn the LEVEL control on the UUT to completely counterclockwise (MIN). Phase switch position does not
matter.
3) Turn on generator; adjust to 100mV, 50 Hz.
4) Plug in UUT; turn the power switch ON. LED should switch from Red to Green. Turn LEVEL control full
clockwise (MAX)
5) LED should Green; immediate and vigorous bass response should be heard and felt from port tube
opening.
6) Turn off generator, turn LEVEL control full counterclockwise (MIN), and disconnect RCA cable.
Sweep Function
1) Follow steps 1-5 above, using a sweep generator as a signal source.
2) Sweep generator from 20Hz to 300Hz. Listen to the cabinet and drivers for any rattles, clicks, buzzes or
any other noises. If any unusual noises are heard, remove woofers and test.
Driver Function
1) Remove woofer from cabinet; detach + and - wire clips.
2) Check DC resistance of woofer; it should be 3.4 ohms ±10%
3) Connect a pair of speaker cables to driver terminals. Cables should be connected to an integrated amplifier
fed by a signal generator. Turn on generator and adjust so that speaker level output is 5.0V.
4) Sweep generator from 20Hz to 1kHz. Listen to driver for any rubbing, buzzing, or other unusual noises.
CS100(CS6100Subwoofer)
8

CS100(CS6100Subwoofer)
9

CS100 SUB (UL)AMP
Troubleshooting Flow Chart
no
yes
yes
yes no
yes
yes
LED red
LED light green yes yes
no
yes yes no
no
yes yes
no
yes yes
yes
no
yes
yes
AMP no signal out
Dc voltage check ±Vcc
Check+/-15VDC
LED light green or red
Check Fuse,Transformer,
D501, etc
Check RY101,D110,Q112,Q113 etc Check CLASS 150W
MODEL
Check ,+VCC& -VCC
DC voltage
Check Q107,Q108,Q109 etc
Check Q501.Q502.Q503,D502 etc
Check,Q206,Q207,U203 etc
Check U202 pin8 signal
Check U201
pin1 signal
Test R147 signal
Check M100 signal The Amp ass’y OK, END
CheckU201,U202,VR201
etc
Check limiter Circuit C317 Check U301,R343,R344 ,
C340,Q301,Q302, etc
Check TH1
CS100(CS6100Subwoofer)
10

CS100 120v Electrical parts List
Part Number Description Qty Reference Designato
Input/Preamp PCB
Resistors
110-16102j26-e Resistor 1K 1/6W ±5% CF 26mm (RoHS) 5 R213,R214,R215,R254,R253
110-16103j26-e Resistor 10K 1/6W ±5% CF 26mm (RoHS) 17
R212,R216,R217,R220,R221,R222,R225,R226,
R227,R228,
R229,R230,R232,R240,R260,R235,R200
110-16104j26-e Resistor 100K 1/6W ±5% CF 26mm (RoHS) 3 R231,R263,R266
,
110-16105j26-e Resistor 1M 1/6W ±5% CF 26mm (RoHS) 1 R259,
110-16122j26-e Resistor 1.2K 1/6W ±5% CF 26mm (RoHS) 1 R265,
110-16124j26-e Resistor 120K 1/6W ±5% CF 26mm (RoHS) 1 R233,
110-16153j26-e Resistor 15K 1/6W ±5% CF 26mm (RoHS) 1 R234,
110-16183j26-e Resistor 18K 1/6W ±5% CF 26mm (RoHS) 1 R262,
110-16205j26-e Resistor 2M 1/6W ±5% CF 26mm (RoHS) 1 R257,
110-16223j26-e Resistor 22K 1/6W ±5% CF 26mm (RoHS) 3 R238,R255,R256
,
110-16224j26-e Resistor 220K 1/6W ±5% CF 26mm (RoHS) 1 R251,
110-16273j26-e Resistor 27K 1/6W ±5% CF 26mm (RoHS) 2 R223,R237,
110-16472j26-e Resistor 4.7K 1/6W ±5% CF 26mm (RoHS) 3 R258,R210,R209
,
110-16473j26-e Resistor 47K 1/6W ±5% CF 26mm (RoHS) 4 R219,R249,R250,R264
,
110-16474j26-e Resistor 470K 1/6W ±5% CF 26mm (RoHS) 1 R252,
110-16512j26-e Resistor 5.1K 1/6W ±5% CF 26mm (RoHS) 1 R211,
110-16513j26-e Resistor 51K 1/6W ±5% CF 26mm (RoHS) 1 R224,
115-h503a102-e VAR Resistor RV16AE-20B2-15K-A54-104(A50K) LEVEL 1 VR201,
Capacitors
129-a154j633-e Metalize CAP. 0.15U 63V ±5% MSC (RoHS) 2 C221,C222,
130-2b221k503-e Disc capacitor 220P 50V ±10% (RoHS) 9 C207,C208,C210,C211,C212,C214,C220,C230
C249,
130-3f104z503-e Disc capacitor 0.1U 50V +80/-20% (RoHS) 8 C232,C242,C244,C245,C246,C252,C254,C256,
130-ch220k503-e Disc capacitor 22PF CH 50V±10% (RoHS) 1 C229,
132-103j503-e Mylar capacitor 0.01uF 50V ±5% (RoHS) 2 C223,C224,
132-104ja03-e Mylar capacitor 0.1UF 100V ±5% (RoHS) 1 C218,
132-223ja03-e Mylar capacitor 0.022uF 100V ±5% (RoHS) 1 C215,
132-473ja03-e Mylar capacitor 0.047uF 100V ±5% (RoHS) 2 C216,C217,
135-3105m50-e Electroytic CAP. 1U 50V ±20% (RoHS) 1 C228,
135-3106m50-e Electroytic CAP. 10uF 50V ±20% (RoHS) 8 C206,C213,C219,C231,C241,C243,C251,C253,
135-3107m16-e Electroytic CAP. 100uF 16V ±20% (RoHS) 1 C234,
135-3226m50-e Electroytic CAP. 22U 50V ±20% (RoHS) 2 C505,C506,
135-3227m16-e Electroytic CAP. 220U 16V ±20% (RoHS) 1 C118,
Semiconductors
192-027c1815gr-e Transistor 2SC1815GR TOSHIBA(RoHS) NPN 3 Q206,Q207,Q208
,
197-631n4148-e Diode 500mW 75V 1N4148 Panjit (RoHS) 9 D201,D202,D207,D208,D211,D212,D214,D21
5
D216,
199-65000513g-e zen Diode GDZJ5.1B 500mW 5.1V 2% 26mm 1N5231B(RoHS) 1 D213,
190-06m4558d-e I.C. OPA 4558D (RoHS) DUAL OP-AMP 1U203,
190-16tl074cn-e *I.C TL074CN ST (RoHS) QUAD OP-AMP 2U201,U202,
195-10204hgw-e dual color LED 204HGW (RoHS) 1 D209,
Miscellaneous
174-0rca108gv-e RCA-108GV purple JK203 (RoHS) 1 JK201,
174-0rcb202vag-e RCA JACK RCA-209 gild (RoHS) 1 JK202,
175-1c07v01-e Wire connector & base 7PIN PITCH=2.5mm (RoHS) 1 M201,
180-tms7210v-e SWITCH SLIDE 6PIN MS7210V (RoHS) 1 SW202,
362-FE-00041-0LAE PCB bracket 11.75*8.5*12.5H (RoHS) 1
CS100(CS6100Subwoofer)

Part Number Description Qty Reference Designato
Main Amp PCB
Resistors
110-14103j26-e Resistor 10K 1/4W ±5% CF 26mm (RoHS) 3 R503,R504,R510
,
110-14222j26-e Resistor 2.2K 1/4W ±5% CF 26mm (RoHS) 1 R511
110-14432j26-e Resistor 4.3K 1/4W ±5% CF 26mm (RoHS) 1 R506,
110-14472j26-e Resistor 4.7K 1/4W ±5% CF 26mm (RoHS) 1 R505,
110-16102j26-e Resistor 1K 1/6W ±5% CF 26mm (RoHS) 1 R153,
110-16103j26-e Resistor 10K 1/6W ±5% CF 26mm (RoHS) 10 R128,R130,R149,R150,R305,R306,R308,R311
R314,R319,
110-16104j26-e Resistor 100K 1/6W ±5% CF 26mm (RoHS) 3 R122,R126,R307
,
110-16153j26-e Resistor 15K 1/6W ±5% CF 26mm (RoHS) 1 R107,
110-16182j26-e Resistor 1.8K 1/6W ±5% CF 26mm (RoHS) 1 R145,
110-16203j26-e Resistor 20K 1/6W ±5% CF 26mm (RoHS) 1 R309,
110-16221j26-e Resistor 220Ω1/6W ±5% CF 26mm (RoHS) 1 R144,
110-16222j26-e Resistor 2.2K 1/6W ±5% CF 26mm (RoHS) 1 R102,
110-16223j26-e Resistor 22K 1/6W ±5% CF 26mm (RoHS) 1 R316,
110-16333j26-e Resistor 33K 1/6W ±5% CF 26mm (RoHS) 1 R310,
110-16393j26-e Resistor 39K 1/6W ±5% CF 26mm (RoHS) 1 R151,
110-16473j26-e Resistor 47K 1/6W ±5% CF 26mm (RoHS) 2 R106,R129,
110-16474j26-e Resistor 470K 1/6W ±5% CF 26mm (RoHS) 2 R127,R312,
110-16562j26-e Resistor 5.6K 1/6W ±5% CF 26mm (RoHS) 1 R152,
110-16621j26-e Resistor 620Ω1/6W ±5% CF 26mm (RoHS) 1 R160,
110-16751j26-e Resistor 750Ω1/6W ±5% CF 26mm (RoHS) 1 R315,
110-16755j26-e Resistor 7.5M 1/6W ±5% CF 26mm (RoHS) 1 R313,
116-161002f26-e Metal film Resistor 10K 1/6W ±1% MF 26mm (RoHS) 2 R301,R303,
116-161102f26-e Metal film Resistor 11.0K 1/6W ±1% MF 26mm (RoHS) 1 R302,
116-162200f26-e Metal film Resistor 220Ω1/6W ±1% MF 26mm (RoHS) 1 R317,
116-162202f26-e Metal film Resistor 22.0K 1/6W ±1% MF 26mm (RoHS) 1 R318,
110-20332jk3-e Resistor 3.3K 2W ±5% standing short feet 7.5m(RoHS) 1 R134,
113-50s68j00-e cement Resistor 0.068Ω5W ±5% horizontal (RoHS) 1 R147,
116-201001jk3x-e oxidation foil Resistor 1.00K 2W ±5% standing 7.5mm (RoHS) 1 R148,
116-304700jk2x-e oxidation foil Resistor 470Ω3W ±5% clip feet 10mm (RoHS) 2 R501,R502,
Capacitors
130-3f104z503-e Disc capacitor 0.1U 50V +80/-20% (RoHS) 6 C107,C117,C122,C144,C320,C322
130-sl101k503-e Disc capacitor 100P 50V SL ±10% (RoHS) 3 C302,C303,C306
,
132-103j503-e Mylar capacitor 0.01uF 50V ±5% (RoHS) 2 C305,C317,
132-103ja03-e Mylar capacitor 0.01uf 100V ±5% (RoHS) 2 C103,C104,
132-104ja03-e Mylar capacitor 0.1UF 100V ±5% (RoHS) 3 C123,C503,C504
,
132-273ja03-e Mylar capacitor 0.027UF 100V ±5% (RoHS) 1 C143,
135-3106m50-e Electroytic CAP. 10uF 50V ±20% (RoHS) 2 C319,C321,
135-3107m10-e Electroytic CAP. 100U 10V ±20% (RoHS) 2 C114,C115,
135-3107m35-e Electroytic CAP. 100U 35V ±20% (RoHS) 2 C507,C508,
135-3225m50-e Electroytic CAP. 2.2U 50V ±20% (RoHS) 1 C509,
135-3226m16-e Electroytic CAP. 22U 16V ±20% (RoHS) 1 C304,
135-3226m50-e Electroytic CAP. 22U 50V ±20% (RoHS) 2 C505,C506,
135-3227m16-e Electroytic CAP. 220U 16V ±20% (RoHS) 1 C118,
135-3476m16-e Electroytic CAP. 47U 16V ±20% (RoHS) 1 C318,
132-103kd00-e Mylar capacitor 0.01U 400V +/-10% long feet (RoHS) 1 C500,
135-4478m63-e Electroytic CAP. 4700uF 63V ±20% (RoHS) 2 C501,C502,
130-3f104z503-e Disc capacitor 0.1U 50V +80/-20% (RoHS) 1 C110,
Semiconductors
190-16tl074cn-e I.C TL074CN ST (RoHS) QUAD OP-AMP 1U301,
192-161tip31c-e Transistor TIP31C SGS (RoHS) NPN 1Q501,
192-162tip32c-e TransistorTIP32C SGS (RoHS) PNP 1Q502,
197-00kbu606g-e diode6A 800V KBU606G (RoHS) BRIDGE 1D501,
197-141n4004-e Diode 1N4004 molding short feet (RoHS) 2 D110,D504,
192-027c1815gr-e Transistor 2SC1815GR TOSHIBA(RoHS) NPN 5Q108,Q109,Q113,Q301,Q302
,
CS100(CS6100Subwoofer)

Part Number Description Qty Reference Designato
Main Amp PCB
192-027c2235y-e Transistor 2SC2235Y TOSHIBA (RoHS) NPN 1Q111,
192-028a1015gr-e Transistor 2SA1015GR TOSHIBA(RoHS) PNP 3Q101,Q107,Q112,
192-1572n5551-e Transistor FSC 2N5551 (RoHS) NPN 2Q114,Q115,
192-1582n5401-e Transistor FSC 2N5401 TO-92 (RoHS) PNP 1Q503,
197-631n4148-e Diode 500mW 75V 1N4148 Panjit (RoHS) 7 D102,D103,D104,D105,D143,D301,D302
199-65000623g-e zener Diode GDZJ6.2B 500mW 6.2V 26mm 2% (RoHS) 1 D101,
199-65001603g-e zener Diode GDZJ16C 500mW 16V 26mm 2% (RoHS) 1 D502,
Miscellaneous
175-1d02v01-e Wire connector & base 2PIN PITCH=3.96mm (RoHS) 1 M100,
175-1d03v01-e Wire connector & base 3 PIN PITCH=3.96mm JST-VH no middle PIN 1M500,
362-FE-00013-0LAE PCB bracket L TYPE t=1.6mm S.P.C.C 89*9*1.6T (RoHS) 2
Class D amp PCB (Replacment of entire module is recommended, part# 051-B00012A-E).
Resistors
118-12061001j-e SMD Resistor 1.00K 1206 5% (RoHS) 7 R2,R11,R29,R30,R7,R9,R25,
118-12061002j-e SMD Resistor 10.0K 1206 5% (RoHS) 3 R7.R9.R25
118-120610r0j-e SMD Resistor 10.0Ω1206 5% (RoHS) 2 R22,R23,
118-12061201j-e SMD Resistor 1.20K 1206 5% (RoHS) 16 R31,R32,R33,R34,R35,R36,R37,R38,R39,R40
R41, R42,R43,R44,R45,R46,
118-12062002j-e SMD Resistor 20.0K 1206 5% (RoHS) 1 R26,
118-12062201j-e SMD Resistor 2.20K 1206 5% (RoHS) 3 R6,R13,R16,
118-12062701j-e SMD Resistor 2.70K 1206 5% (RoHS) 1 R10,
118-12063000j-e SMD Resistor 300.0Ω1206 5% (RoHS) 1 R24,
118-12063301j-e SMD Resistor 3.30K 1206 5% (RoHS) 4 R14,R15,R27,R28,
118-12063902j-e SMD Resistor 39.0K 1206 5% (RoHS) 1 R3,
118-12064700j-e SMD Resistor 470Ω1206 5% (RoHS) 1 R8,
118-12064701j-e SMD Resistor 4.70K 1206 5% (RoHS) 3 R1,R5,R12,
118-12064702j-e SMD Resistor 47.0K 1206 5% (RoHS) 1 R17,
118-12064704j-e SMD Resistor 4.70M 1206 5% (RoHS) 1 R4,
118-120647r0j-e SMD Resistor 47.0Ω1206 5% (RoHS) 2 R20,R21,
Capacitors
141-c0101k50-e SMD capacitor 100pF 50V 10% 1206 NP0 (RoHS) 1 C4,
141-c0220k50-e SMD capacitor 22pF 50V 10% 1206 SMT NPO (RoHS) 1 C5,
141-c0561k50-e SMD capacitor 560pF 50V 10% 1206 NPO (RoHS) 1 C6,
141-c5104m50-e SMD capacitor 1206 Y5V 0.1uF 50V ±20% (RoHS) 8 C2,C3,C7,C8,C9,C10,C11,C15,
141-c7223k50-e SMD capacitor 0.022uF 50V 10% 1206 X7R (RoHS) 1 C13,
141-d7104ka0-e SMD capacitor 0.1uF 100V 10% 1210 X7R (RoHS) 1 C12,
141-d7104kb5-e SMD capacitor 0.1uF 250V 10% 1210 X7R (RoHS) 5 C1,C18,C19,C20,C14,
128-e106ma01k-e non-polarity Electroytic CAP. 10UF 100V 20% 105℃(RoHS) 2C16,C17,
Semiconductors
190-16tl072dts-e SMD I.C. TL072CDT SGS THOMSON DUAL OP-AMP 1IC1,
192-09124126qs-e SMD Transistor 2SC2412K-T146Q/R ROHM (RoHS) 3 Q1,Q4,Q5,
192-09139066rs-e SMD Transistor 2SC3906K-T146R ROHM (RoHS) 2 Q2,Q8,
192-09210376qs-e SMD Transistor 2SA1037K-T146Q/R ROHM (RoHS) 2 Q7,Q9,
192-09215146rs-e SMD Transistor 2SA1514K-T146R ROHM (RoHS) 2 Q3,Q6,
197-03rls4148s-e SMD Diode RLS4148-TE11 ROHM (RoHS) 6 D1,D2,D3,D4,D5,D6,
199-15000563s-e SMD ZENER 5.6V 5% PHILIPS BZX84-C5V6 (RoHS) 2 Z1,Z2,
199-1500120s-e SMD ZENER 12V 5% PHILIPS BZX84-C12 (RoHS) 2 Z5,Z6,
199-15001503s-e SMD ZENER 15V 5% PHILIPS BZX84-C15 (RoHS) 2 Z3,Z4,
192-232irf9640-e FET IRF9640 IR P-CH TO220 (RoHS) 1 Q10,
192-233f640n-e Transistor IRF640N INTERNATIONAL (RoHS) 1 Q11,
CS100(CS6100Subwoofer)

Part Number Description Qty Reference Designato
Class D amp PCB (Replacment of entire module is recommended, part# 051-B00012A-E).
Miscellaneous
122-14121m4191-e Ferrite core 日font LS-A6206-ST EFD-30 (RoHS) 1 L1,
122-14350j4180-e inductor 35uH Ferrite Core 25 Milliohm (RoHS) 1 L2,
175-9f40hr2-e Wire connector & base 40PIN PITCH=2.54mm HR2*40
MISCELLANEOUS/MECHANICAL
109-1ttc802j0-e thermistor Resistor TTC-802(JS) NTC long feet (RoHS) 1 TH1,
120-1000003-e inductor 10W AI YT-C3104-005 1CRHW 354708LTB (RoHS) 2FB1,FB2,
162-50129001-e CABLE ASS'Y row wire 120mm AWG28 WHT (RoHS) 1 W201,
171-urwh124d-e relay RWH-SH-124D (1600 ohm) (RoHS) 1 RL1,
150-r4055900-e Power transformer I/P:120V/60Hz TT0900008720 (RoHS) 1 T501,
152-u602015-e Line cord tie-in with polarity SVT FT-2 6FT both insulation 1
154-k31505t0-e Fuse 3.15A 250V 30mm UL/CSA/PSE (RoHS) 1 F501,
155-63032i-e Fuse holder HTB-32I 30mm UL/CSA (RoHS) 1 for F501,
156-h200040-e pyrocondensation sleeve 20ψ*40mm (RoHS) 1
156-h200050-e pyrocondensation sleeve 20Φ50mm (RoHS) 1
162-10151001-e WIRE UL1617 150mm 22AWG BROWN 6:6 (RoHS) 1
162-a040d001-e speaker wire #1015 400mm 991110-00 (HG150 use ) (RoHS) 1
176-wjce1-e Wire connector pin CE-1 (RoHS) 1
180-pbr12c11s-e power switch PUSH BR12C11S (RoHS) 1 SW501,
193-201815t2-e ceramic insulator (RoHS) 2
302-AL-05092-0LAE Rear board 270*215*2.5T al, black printing CSC100 120V 1
306-ABS-00004-0BAE Rear housing REAR CABINET 268*213*102 A.B.S UL (RoHS) 1
311-ABS-00028-0BAE Plastic knob 46077-W soft material P.V.C. (RoHS) LEVEL 1
317-000-00037-0LAE earth end M3 solder t=0.3 (RoHS) 1
323-AL-00056-0LAE Heat sink 83.5*50.5*27.5H degrease 1
333-EVA-00096-0BAE EVA gasket wide side 213*15*2.0mm (RoHS) 2
333-EVA-00097-0BAE EVA gasket wide side 213*15*1.0t (RoHS) 2
333-EVA-00132-0BAE EVA gasket Long side 238*15*2.0mm (RoHS) 2
333-EVA-00133-0BAE EVA gasket Long side 238*15*1.0t (RoHS) 2
333-EVA-00188-0BAE EVA gasket 170x5x1t back with glue (RoHS) 1
333-EVA-00219-0BAE EVA gasket wide side 150*15*1t UL (RoHS) 1
333-EVA-00220-0BAE EVA gasket Long side 225*15*1t UL (RoHS) 1
335-NYL-05015-0BAE Line cord fixed button SB4F-2 black (RoHS) 2
350-EM04012D024-E 4￠*12 Wood screw electric black (RoHS) 4
351-AM03008A078-E M3*8 Machin screw plating nickel (RoHS) 4
351-AM03008A079-E M3*8 Machin screw electric black (RoHS) 3
352-AM03008D040-E ￠3*8 B ping screw electric black (RoHS) 2
352-AM03008D041-E ￠3*8 B ping screw plating nickel (RoHS) 2
352-AM03010D065-E ￠3*10 P ping screw electric black (RoHS) 2
352-HM03012D086-E ￠3*12 B ping screw electric black (RoHS) 1
CS100(CS6100Subwoofer)

CS100(CS6100Subwoofer)
15

CS100(CS6100Subwoofer)
16

CS100(CS6100Subwoofer)
17

CS100(CS6100Subwoofer)
18

CS100(CS6100Subwoofer)
19