JCM Technologies KEEROLL User manual

jcmtechnologies
user manual
KEEROLL KIT
KEEROLL + RSENS3 TGL868 + 2 MUV
EN

KEEROLL
jcmtechnologies
2
Introduction 3
General description 3
RadioSens3 System description 5
Installation 6
Control panel fixations 6
Connections 8
Configuration / Starting up 10
Options selection 10
Programming 11
Transmitter programming 11
Safety elements programming 11
Manoeuvre programming 12
Verification 13
Verify that the control panel is working properly 13
Communication’s quality 13
Impact detection adjustment 13
Maintenance 14
Fuse replacement 15
Battery replacement of RadioSens3 transmitter 15
Use of the system 15
Troubleshooting 16
Troubleshooting 16
Technical Data 17
Electrical parameters 17
Radio transmitters frequency parameters 17
Radio safety elements frequency parameters 17
Notes 18
Regulatory Data 20
Safety instructions for installation 20
Safety instructions for the use 20
EC Declaration of Conformity 20

KEEROLL
3
Introduction
General description
Designed for residential aluminium roller shutters, the KEEROLL solution, together with the RadioSens3
system, has direct communication with the user and the installer.
Its capacitive front with illuminated keys provides comfort and security. The door can be opened and
closed by any person without the need for technical know-how. The installer requires no initial training
in the product.
The control panel incorporates the most advanced system for detecting obstacles via radio, without
wires. With the RadioSens3 system you can forget about fitting a safety edge. You only need to fit the
transmitter onto the last slat of the door to comply with all safety regulations. It's clean, quick and
straightforward.
In addition, the system includes two smart-looking pocket transmitters that allow you to open the door
from your car.
The system complies with standard EN ISO 13849-1: 2008, category 2, PLd.

KEEROLL
jcmtechnologies
4
Indicators
Actions
Press to open, stop and close the door.
Press to close the door in dead man mode.
Block function: KEEROLL control panel incorporates a block button on the cover to
prevent the door from being opened accidentally.
Press to block the door, key lights ON.
The control panel will not be able to move the door neither to receive any transmitter.
Useful function to block the door during the night.
Adjust self-closing time: The user can set the desired time to leave the door open
simply by pressing a button on the cover.
New transmitters: The user can program new transmitters simply by pressing a
button on the cover (deleting transmitters is an action that is only allowed in installer
mode).
Alarm function: With the ALARM accessory it is possible to detect unwanted
openings of the door (robbery), enabling the control panel’s
sound alarm to be activated, or even connecting it to the
alarm system already present in the home.
Dipswitch 4 at ON. With door totally closed, if someone
tries to move it manually, the alarm will be activated.
To stop the alarm, press any button of a programmed transmitter.
ALARM device is
necessary to
activate this
function

KEEROLL
5
RadioSens3 System description
RadioSens3 is an impact detection system installed at the last slat of the roller shutter. It detects the
obstacle and reopens without causing any damage.
The communication system between the RS3 T868 and the KEEROLL is permanently monitored (two-
way link via radio)
Battery life
Table
Battery life in days
Manoeuvres / day
Manoeuvre time (s)
25
10
5
4
10
320
410
440
450
15
275
375
425
435
20
250
350
410
420
25
220
325
385
410
30
200
300
375
390
Options and
sensibility selectors
must be set before
programming. Any
later change will
have no effect.
(guide values, with alkaline batteries and at an ambient temperature of 25ºC)

KEEROLL
jcmtechnologies
6
Installation
Control panel fixations
Remove the front cover of the control panel. Install the bottom part on the wall in a vertical position, at
least 1,5 meters over the ground and in accordance with the assembly instructions below.
1st
2nd
2nd

KEEROLL
7
RadioSens3 fixations
Install the transmitter in horizontal position, at the middle of the last slat. Avoid placing metallic
surfaces between the receiver and the transmitter.
Control panel detects automatically the limit switches in the tubular motor. An adjustment of the limit
switches before RadioSens3 installation is requested.
SWIPE TO OPEN COVER REMOVE COVER DRILL DOOR
Maximum width of the door: 4 m
Recommended door speed: 0.1m/s or higher
(and 17 rpm motors).
<10m
The last
slat must
have a
tolerance of
minimum
1mm of
movement.

KEEROLL
jcmtechnologies
8
Connections
To prevent electric shocks, the equipment must be
disconnected from the power supply and all the electrical
connections.

KEEROLL
9

KEEROLL
jcmtechnologies
10
Configuration / Starting up
Connect the power supply
Adjusting limit switch
Dipswitch 1 at ON. Door will move in dead man mode. Keep pressed or to move
up and down the door.
Press , to change the phase of the motor in case the door is not moving in the proper
sense.
Dipswitch 1 at OFF to exit dead man mode.
Options selection
Dipswitch function
OFF
ON
1- DEADMAN
Normal operation
Dead man operation
2- SAFETY EDGE WIRED
8K2 safety edge connection
Optical safety edge connection
3- PRE-FLASH
Pre-flash disabled
3s pre-flash enabled
4- ALARM* (detector needed)
Alarm function disabled
Alarm function enabled
5- COURTESY LIGHT / ALARM
Courtesy light output
External alarm output
6- TEST PHOTO
Test photocell disabled
Test photocell enabled
* Optional alarm. JCM can provide you the alarm detector (optional)
Door MUST BE AT HALFWAY position before
starting the limit switch adjusting