JENCO VisionPlus 6177 User manual

0
Operation Manual
MODEL 6177
Microcomputer Based
pH/ORP/Temperature
Benchtop Meter
6177

1
CONTENTS
GENERAL INTRODUCTION…………………................2
INITIAL INSPECTION……...………………....................2
POWER INPUT…….……...………………......................2
INSTALLING THE BATTERIES..…………....................3
DISPLAY & KEYS FUNCTIONS…..……………..…...…..…4
A. Display ......................................................................4
B. Keys...........................................................................5
OPERATIONAL PROCEDURES..……..........................6
A. Buffer Set Selection.....................................................6
B. pH Calibration.............................................................6
a. Calibration with an ATC/Temp probe in the pH-AUTOLOCK
mode........................................................................6
b. Calibration with manual temperature compensation in the
pH AUTOLOCK mode....................................................7
c. Calibration with an ATC/Temp probe in the pH NON-
AUTOLOCK mode........................................................8
d. Calibration with manual temperature compensation in the
pH NON-AUTOLOCK mode..............................................9
C. pH Measurements........................................................9
a. Measurement with an ATC/Temp probe in the pH-AUTOLOCK
mode........................................................................9
b. Measurement with manual temperature compensation in the
pH AUTOLOCK mode..................................................10
c. Measurement with an ATC/Temp probe in the pH NON-
AUTOLOCK mode......................................................10
d. Measurement with manual temperature compensation in the
pH NON-AUTOLOCK mode............................................11
D. Temperature Measurements.......................................11
E. mV Measurements.....................................................11
a. Measurement in the mV-AUTOLOCK mode....................11
b. Measurement in the mV NON-AUTOLOCK mode.............11
pH BUFFERS..…………………………….....................12
ERROR DISPLAYS AND TROUBLESHOOTING.......13
SPECIFICATIONS………………..……........................14
WARRANTY…………………………….........................15

2
GENERAL INTRODUCTION
Thank you for selecting the 6177 meter. The 6177 is a precision tool
that measures pH, mV and temperature. A built-in microprocessor
stores, calculates and compensates for all parameters related to pH
determinations including pH electrode temperature characteristics,
electrode slope deviations and buffer solutions.
This meter has a waterproof IP54 case. The mechanical keys are
highly reliable with tactile and audio feedback. It is powered by six
AAA-size alkaline batteries or with a UL / CE approved AC adapter
(OUTPUT:DC9V). The meter also displays a “BAT” message when
the batteries are in need of replacement. Re-calibration is not
required when power is restored.
The front of the meter has a large LCD that displays pH or mV and
temperature simultaneously along with user prompts and mode
indicators. The unit prompts the user through calibration and
measurement procedures.
An AUTOLOCK feature for both pH and mV measurements enables
the unit to automatically sense the end point and “LOCK” the display
to indicate the end point value of a measurement. AUTOLOCK and
user prompts help eliminate most errors in determining pH and mV
values, resulting in precise, repeatable and error-free
measurements. The 6177 can also be used in non-AUTOLOCK
mode.
The model 6177 is available with pH, ORP and ATC (Automatic
Temperature Compensation) probes. Other features include up to 3
points calibration, electrode offset recognition, electrode slope
recognition, electrode efficiency display, built-in buffer coefficients,
automatic or manual temperature compensation, long battery life,
and 50/60Hz AC noise rejection. This meter is user-friendly for
laboratory application.
INITIAL INSPECTION
Carefully unpack the unit and accessories. Inspect for damages
made in shipment. If any damage is found, notify your JENCO
representative immediately. All packing materials should be saved
until satisfactory operation is confirmed.
POWER INPUT
The model 6177 can be powered by an UL / CE approved 100 ~ 240
VAC adaptor as well as 6 “AAA” alkaline batteries. Check the label
on the AC adaptor supplied with the instrument to make sure that
the AC line voltage is correct. If the wrong AC adaptor is supplied,
notify your JENCO representative immediately.

3
INSTALLING THE BATTERIES
To insert the batteries into the meter, follow the procedure outlined
below.
1. Use a Philip screw driver and unlock the battery cover by
turning the screw driver in the counter clockwise direction.
After unlocking the screw, take off the battery cover (Fig.1)
2. Replace the old batteries with new ones and install them on
the correct polarity position.
3. Put the battery cover back on the instrument. Use a Philip
screw driver and turn the screw in the clockwise direction to
lock the battery cover.
Figure 1: Battery compartment

4
DISPLAY & KEYS FUNCTIONS
A. Display
1
2
3
4
5
6
7
9
10
12
11
8
Figure2: Active LCD screen
1. WAIT-
This will be displayed when the
unit is still waiting for a stable
reading or end point sensing.
7. AUTO-
AUTOLOCK mode indicator.
2. BAT-
Low battery indicator.
8. Buffer selection-
This indicator will flash if the
unit is not yet calibrated. This
indicator will remain lit-up if
the unit has been calibrated.
3. pH-
Unit and mode indicators.
9. LOCK-
This will indicate that the
reading is frozen during
AUTOLOCK mode.
4. mV-
Unit and mode indicators.
10. EFF-
This will be displayed if the
user is viewing the efficiency
of the electrode. It is
recommended to use a new
electrode when the efficiency
value is less over than 75%.
5. ATC/MAN-
ATC indicator will be displayed
if a temperature probe is
connected otherwise the MAN
indicator will be displayed.
11. MAIN DISPLAY-
For pH, mV and probe
efficiency values
6. CAL-
This will be displayed when the
unit enters into the calibration
mode.
12. SECONDARY DISPLAY-
For temperature in ℃.

5
B. Keys
Mea.
Eff.
Stand
Slope
Mode
Clear
On/Off-
Press and hold this key for 2 seconds to power on
and shut off the meter.
Mea.
Eff.
Stand
Slope
Mode
Clear
Mode-
Selects display mode. Pressing this key changes the
display sequentially to display pH-AUTO, mV-AUTO,
pH and mV. The calibration values will not be
affected by changing the display modes. In “pH
calibration”, press “Mode” key to exit calibration
mode.
Mea.
Eff.
Stand
Slope
Mode
Clear
Clear-
It is used to clear the unit when error signal appears.
It clears all calibration values stored in the internal
memory.
Under normal use the key will not be activated unless
pressed and held for 2 seconds to prevent accidental
erasing stored memory.
In pH mode, when the “Clear” key is pressed for 5
seconds, all segments of the LCD will be on. After
about 2 seconds the unit will enter the pH-AUTO
mode. The “AUTO” and “CAL” will be displayed and
one of the buffer values in the pre-selected buffer set
shall begin to flash. This means that the unit is
un-calibrated and requires new pH calibration before
use.
Mea.
Eff.
Stand
Slope
Mode
Clear
Mea.
Eff.
Stand
Slope
Mode
Clear
Up/Down-
These two keys are used to manually enter the
temperature values. They have no effect on the unit
when operating in ATC mode.
Mea.
Eff.
Stand
Slope
Mode
Clear
Mea.
Eff.
Stand
Slope
Mode
Clear
Stand/Slope-
The “Stand” and “Slope” keys are used for pH
calibration of the unit. Press and hold the “Stand”
key while turning on the device power, will switch the
pH buffer set.
Mea.
Eff.
Stand
Slope
Mode
Clear
Mea. / Eff.-
1. The key is used to bring the unit out of the AUTO
condition when operating in the pH-AUTOLOCK or
mV (RmV) - AUTOLOCK mode.
2. In the pH measure mode, press and hold this key
for 5 seconds, the LCD will display the efficiency of
the electrode and the offset value.

6
OPERATIONAL PROCEDURES
A. Buffer Set Selection
The 6177 meter has two buffer sets: 7.00, 4.01, 10.01 pH and 6.86,
4.00, 9.18 pH. To change the buffer set, turn off the unit, then press
and hold the “Stand” key while turning on the unit again.
[Note: There is no need to repeat this procedure every time the unit
is power up unless one decides to change the buffer settings.]
B. pH Calibration
The 6177 uses up to 3 points calibration.
[Note: If the device requires to calibrate more than one calibration
point, the first point must be 6.86/7.00 pH, and the second point can
either be 4.00/4.01 pH or 9.18/ 10.01 pH.]
a. Calibration with an ATC/Temp probe in the pH-AUTOLOCK
mode.
1. Turn the unit on. In pH mode, press “Clear” key for 5
seconds, all LCD elements will lit up. The meter clears all
calibration values stored in internal memory.
2. Connect the pH electrode to the BNC connector and the
ATC/Temp probe to the ATC/Temp connector of the unit:
“ATC” icon will lit up. “pH” icon, “AUTO” icon and "CAL" icon
will lit up. One of the buffer in the pre-selected buffer set will
start to flash.
3. Rinse the pH and ATC/Temp probes in distilled water and
immerse them in the first buffer solution. Allow temperature
reading to stabilize, then press and hold “Stand” key for 2
seconds to calibrate. The “WAIT” icon will flash until the unit
detects a stable reading. Once the unit calibrates the first
point, the selected buffer will lit up while two other selectable
buffers start to flash. The unit is ready to be sloped at the
second buffer.
[Note: If the first buffer solution is 7.00 or 6.86, at this
moment, press the “Mode” key. The unit will exit the
calibration mode. Single point calibration is complete.
If the first buffer solution is 4.00, 4.01, 9.18 or 10.00 pH, at
this moment, the unit will automatically exit the calibration
mode. Single point calibration is complete.]
3. Rinse the pH and ATC/Temp probe in distilled water and
immerse them in the second buffer solution (either 4.00/4.01
pH or 9.18/10.01 pH corresponding to the flashing number on

7
display). Allow temperature reading to stabilize, then press
“Slope” key to calibrate. The “WAIT” icon will flash until the
unit detects a stable reading. Once the unit calibrates the
second point, the selected two buffers lit up and the
remaining buffer starts to flash. The unit is ready to be sloped
at the third buffer.
[Note: At this moment, press the “Mode” key, the unit will
exit the calibration mode. Dual point calibration is complete.]
4. Rinse the pH and ATC/Temp probe in distilled water and
immerse them in the third buffer solution (either 4.00/4.01
pH or 9.18/10.01 pH corresponding to the flashing number
on display). Allow temperature reading to stabilize, then
press “Slope” key to calibrate. The “WAIT” icon will flash
until the unit detects a stable reading. Once the unit
calibrates the third point and the unit will automatically exit
the calibration mode. Three point calibration is complete.
5. The unit calculates and compensates for the pH electrode
slope deviation corresponding to the values of the calibrated
buffers. After calibration, press and hold “Mea./Eff.” key for
about 5 seconds to display the new electrode efficiency and
offset.
b. Calibration with manual temperature compensation in the
pH-AUTOLOCK mode.
1. Turn the unit on. In pH mode, press “Clear” key for 5 seconds,
all LCD elements will lit up. The meter clears all calibration
values stored in internal memory.
2. Connect the pH electrode to the BNC connector and the
ATC/Temp probe to the ATC/Temp connector of the unit:
“MAN” icon will lit up. “pH” icon, “AUTO” icon and "CAL" icon
will lit up. One of the buffer in the pre-selected buffer set will
start to flash.
3. Rinse the pH probes in distilled water and immerse it in the
first buffer solution. Adjust the temperature reading to that of the
first buffer using the “up” or “down” keys (0.0 to 60.0 ℃). Then
press and hold “Stand” key for 2 seconds to calibrate. The
“WAIT” icon will flash until the unit detects a stable reading.
Once the unit calibrates the first point, the selected buffer
remains lit up while two other selectable buffers start to flash.
The unit is ready to be sloped at the second buffer.
[Note: If the first buffer solution is 7.00 or 6.86 pH, at this
moment, press the “Mode” key, the unit will exit the
calibration mode. Single point calibration is complete.
If the first buffer solution is 4.00, 4.01, 9.18 or 10.01 pH, at

8
this moment, the unit will automatically exit the calibration
mode. Single point calibration is complete.]
4. Repeat steps 4~6 of “Calibration with an ATC/Temp probe in
the pH-AUTOLOCK mode” for dual and three point calibration.
c. Calibration with an ATC/Temp probe in the pH NON-
AUTOLOCK mode.
1. Turn the unit on. In pH mode, press “Clear” key for 5 seconds,
all LCD elements will lit up. The meter clears all calibration
values stored in internal memory.
2. Connect the pH electrode to the BNC connector and the
ATC/Temp probe to the ATC/Temp connector of the unit:
“ATC” icon will lit up. Press “Mode” key to select “pH” mode.
“pH” icon and "CAL" icon will lit up. One of the buffer in the
pre-selected buffer set will start to flash.
3. Rinse the pH and ATC/Temp probes in distilled water and
immerse them in the first buffer solution. Allow temperature
reading to stabilize, then press and hold “Stand” key for 2
seconds to calibrate, the unit immediately calibrates the first
point, the selected buffer remains lit up while the remaining
two buffers start to flash. The unit is ready to be sloped at the
second buffer.
[Note: If the first buffer solution is 7.00 or 6.86 pH, at this
moment, press the “Mode” key, the unit will exit the calibration
mode. Single point calibration is complete.
If the first buffer solution is 4.00, 4.01, 9.18 or 10.01 pH, at this
moment, the unit will automatically exit the calibration mode.
Single point calibration is complete.]
4. Rinse the pH and ATC/Temp probe in distilled water and
immerse them in the second buffer solution (either 4.00/4.01
pH or 9.18/10.01 pH corresponding to the flashing number on
display). Allow temperature reading to stabilize, then press
“Slope” key to calibrate. The unit immediately calibrates the
second point, the selected two buffers lit up and the remaining
buffer starts to flash. The unit is ready to be sloped at the third
buffer.
[Note: At this moment, press the “Mode” key, the unit will
exit the calibration mode. Dual point calibration is complete.]
5. Rinse the pH and ATC/Temp probe in distilled water and
immerse them in the third buffer solution (either 4.00/4.01 pH
or 9.18/10.01 pH corresponding to the flashing number on
display). Allow temperature reading to stabilize, then press
“Slope” key to calibrate. The unit immediately calibrates the

9
third point and the unit will automatically exit the calibration
mode. Three points calibration is complete.
6. The unit calculates and compensates for the pH electrode
slope deviation corresponding to the values of the three
calibration buffers. After calibration, press and hold
“Mea./Eff.” key for about 5 seconds to display the new
electrode efficiency and offset.
d. Calibration with manual temperature compensation in the
pH NON-AUTOLOCK mode.
1. Turn the unit on. Press “Clear” key for 5 seconds, all LCD
elements will lit up. The meter clears all calibration values
stored in internal memory.
2. Connect the pH electrode to the BNC connector of the unit,
“MAN” icon will lit up. Press “Mode” key to select “pH” mode.
“pH” icon and "CAL" icon will lit up. One of the buffer in the
pre-selected buffer set will start to flash.
3. Rinse the pH probes in distilled water and immerse it in the
first buffer solution. Adjust the temperature reading to that of the
first buffer using the “Up” or “Down” keys (0.0 to 60.0 ℃)
before pressing “Stand” key. Then press and hold “Stand”
key for 2 seconds to calibrate. The unit immediately calibrates
the first point, the selected buffer remains lit up while the
remaining two buffers start to flash. The unit is ready to be
sloped at the second buffer.
[Note: If the first buffer solution is 7.00 or 6.86 pH, at this
moment, press the “Mode” key, the unit will exit the calibration
mode. Single point calibration is complete.
If the first buffer solution is 4.00, 4.01, 9.18 or 10.01 pH, at this
moment, the unit will immediately exit the calibration mode.
Single point calibration is complete.]
4. Repeat steps 4~6 of “Calibration with an ATC/Temp probe in
the pH NON- AUTOLOCK mode” for dual and three point
calibration.
C. pH Measurements
To take pH measurements, 6177 must be calibrated before first
use.
a. Measurement with an ATC/Temp probe in the pH-
AUTOLOCK mode.
1. Connect the pH electrode to the BNC connector and the
ATC/Temp probe to the ATC/Temp connector of the unit. The

10
“ATC” icon will lit up.
2. Press “Mode” key until “pH” icon and “AUTO” icon lit up.
3. Rinse the pH electrode and ATC/temp probe with distilled
water and immerse in the sample to be measured. Remove
any air bubbles trapped around the probe by shaking or
stirring the probe.
4. Press the “Mea./Eff.” key. The “WAIT” icon will start flashing.
The unit is waiting for a stable reading. The display will track
the pH value as sensed by the pH electrode and the
ATC/Temp probe.
5. When the “WAIT” icon disappears, the reading is then “LOCK”
and will not respond to further changes from the sample. The
pH value shown is the pH value of the sample at the displayed
sample temperature.
[Note: For samples that are inherently unstable, the unit will
not AUTOLOCK. In this case, use the pH NON- AUTOLOCK
mode for measurements.]
b. Measurement with manual temperature compensation in
the pH-AUTOLOCK mode.
1. Connect the pH electrode to the BNC connector of the unit.
The “MAN” icon will lit up. Set unit to display the sample
temperature by pressing the “Up” and “Down” keys (0.0 ~
100.0 ℃).
2. Repeat steps 2~5 of “Measurement with an ATC/Temp
probe in the pH- AUTOLOCK mode”.
c. Measurement with an ATC/Temp probe in the pH NON-
AUTOLOCK mode.
1. Connect the pH electrode to the BNC connector and the
ATC/Temp probe to the ATC/Temp connector of the unit. The
“ATC” icon will lit up.
2. Press “Mode” key until “pH” icon lit up.
3. Rinse the pH electrode and ATC/temp probe with distilled
water and immerse in the sample to be measured.
4. Allow sufficient time for the display to stabilize. The instrument
will display the pH value of the sample at the displayed sample
temperature.

11
d. Measurement with manual temperature compensation in
the pH NON-AUTOLOCK mode.
1. Connect the pH electrode to the BNC connector of the unit.
The “MAN” icon will lit up. Set unit to display the sample
temperature by pressing the “Up” and “Down” keys (0.0 ~
100.0 ℃).
2. Repeat steps 2~4 of “Measurement with an ATC/Temp
probe in the pH NON- AUTOLOCK mode”.
D. Temperature Measure
The 6177 can measure temperature independently with the
ATC / temp probe without using the pH electrode. Place the
ATC / temp probe in the sample. The unit will display the
measured temperature.
E. mV Measurements
a. Measurement in the mV-AUTOLOCK mode.
1. Connect the optional combination ORP electrode to the BNC
connector of the unit.
2. Press “Mode” key until “mV” icon and “AUTO” icon lit up.
3. Rinse electrode with distilled water and immerse it in sample to
be measured.
4. Press the “Mea./Eff.” key. The “WAIT” icon will start flashing.
The unit is waiting for a stable reading. The display will track
the mV value as sensed by the ORP electrode.
5. When the “WAIT” icon disappears, the reading is then “LOCK”
and will not respond to further changes from the sample. The
mV value is the sample reading.
[Note: For samples that are inherently unstable, the unit will
not AUTOLOCK. In this case, use the m NON- AUTOLOCK
mode for measurements.]
b. Measurement in the mV NON-AUTOLOCK mode.
1. Connect the optional combination ORP electrode to the BNC
connector of the unit.
2. Press “Mode” key until “mV” icon lit up.
3. Rinse electrode with distilled water and immerse it in sample to
be measured.

12
4. Allow sufficient time for the display to stabilize. The instrument
will display the mV value of the sample.
pH BUFFERS
The temperature coefficient of pH calibration buffers 4.00, 4.01, 6.86,
7.00, 9.18 and 10.01 pH are stored inside the instrument. The
buffers used to calibrate the instrument must exhibit the same
temperature characteristics as the stored values.
Temperature coefficient of the pH buffers
℃
4.00
6.86
9.18
4.01
7.00
10.01
0
4.01
6.98
9.46
4.01
7.11
10.32
5
4.00
6.95
9.39
4.01
7.08
10.25
10
4.00
6.92
9.33
4.00
7.06
10.18
15
4.00
6.90
9.28
4.00
7.03
10.12
20
4.00
6.88
9.23
4.00
7.01
10.06
25
4.00
6.86
9.18
4.01
7.00
10.01
30
4.01
6.85
9.14
4.01
6.98
9.97
35
4.02
6.84
9.10
4.02
6.98
9.93
40
4.03
6.84
9.07
4.03
6.97
9.89
45
4.04
6.83
9.04
4.04
6.97
9.86
50
4.06
6.83
9.02
4.06
6.97
9.83
55
4.07
6.83
8.99
4.08
6.97
9.80
60
4.09
6.84
8.97
4.10
6.98
9.78
[Note: The actual reading of the instrument can differ from the
values shown by ±0.01pH.]

13
ERROR DISPLAYS AND TROUBLESHOOTING
[Note: If the meter still does not perform normally after the above
measures are taken, call JENCO representative.]
Main
Display
Possible cause(s)
Corrective Action(s)
"Er1"
1. “Stand” was pressed
before the electrode and
ATC/Temp probe settled
to within +/-1.5 pH of the
buffer value.
2. pH electrode offset is
greater / less than +/-1.5
pH.
3. pH electrode is faulty.
1. Press “Clear” key, allow
sufficient time for the
electrode and ATC/Temp
probe to stabilize, re-press
“Stand” key to start the
calibration procedure.
2. Replace the buffer and /or
the pH electrode. Press
“Clear” key to recalibrate
meter.
3. Replace electrode.
"Er2"
1. “Slope” was pressed
before the electrode and
ATC/Temp probe settled
to within 30% of the
buffer value.
2. Buffer 4.00, 4.01, 9.18
and 10.01 pH is not
correct.
3. pH electrode slope is off
by more than 30% of
ideal slope.
1. Allow sufficient time for the
electrode and ATC/Temp
probe to stabilize, re-press
“Slope” key to continue
the calibration procedure.
2. Check if the correct buffer
is used.
3. Replace the buffer and /or
the pH electrode. Press
“Clear” key to recalibrate
meter.
"Er3"
1. Temperature is out of the
0.0 ~ 60.0 °C range.
1. Bring the buffer
temperature within range.
"over"
/ ”undr”
1. Measured pH is out of
the -2.00 ~ 16.00 pH
range.
2. Measured mV is out of
the –1999.9 ~ 1999.9 mV
range.
3. Measured temperature is
out of the 0.0 ~ 100.0 °C
range.
1. Bring sample pH into the
correct measuring range.
2. Bring sample ORP into the
correct measuring range.
3. Bring sample temperature
into the correct measuring
range.

14
SPECIFICATIONS
Display
Range
Resolution
Accuracy
pH
-2.00 to 16.00 pH
0.01 pH
±0.01 pH
mV
-1999.9 to 1999.9 mV
0.1mV
±0.05% F.S.
Temperature
0.0 to 100.0 °C
0.1 °C
±0.2°C
pH buffer recognition
7.00, 4.01, 10.01 pH or 6.86,
4.00, 9.18 pH
pH Temperature compensation
AUTO/MAN 0.0 ~ 100.0 °C
pH Buffer Temperature range
0.0 ~ 60.0°C
pH Electrode Offset recognition
±100 mV at 7.00 pH
or +108.3/-91.7mV at 6.86 pH
pH Electrode Slope recognition
±30% at 4.00, 4.01, 9.18 and
10.01 pH
Input impedance
>1012 Ω
Temperature sensor
Thermistor, 10 k Ω at 25 °C
Power
6 X 1.5 V AAA Batteries or
100 ~ 240 VAC adapter
Calibration Back-up
EEPROM
Audio Feedback
All Touch Keys
End Point Sensing & Hold
Yes
Screen
Segment LCD backlight
Ambient Temperature Range
0 ~ 50 °C
Relative Humidity
up to 90%
Case
IP54
Dimensions (W x D x H)
150 x 210 x 45 mm
Weight
430 grams

15
WARRANTY
JENCO warrants this product to be free from significant deviations
in material and workmanship for a period of 1 year from date of
purchase. If repair or adjustment is necessary and has not been
the result of abuse or misuse, within the year period, please
return-freight-prepaid and the correction of the defect will be made
free of charge. If you purchased the item from our JENCO
distributors and it is under warranty, please contact them to notify
us of the situation. JENCO Service Department alone will
determine if the product problem is due to deviations or customer
misuse.
Out-of-warranty products will be repaired on a charge basis.
RETURN OF ITEMS
Authorization must be obtained from one of our representatives
before returning items for any reason. When applying for
authorization, have the model and serial number handy, including
data regarding the reason for return. For your protection, items
must be carefully packed to prevent damage in shipment and
insured against possible damage or loss. JENCO will not be
responsible for damage resulting from careless or insufficient
packing. A fee will be charged on all authorized returns.
NOTE: JENCO reserves the right to make improvements in
design, construction and appearance of our products without
notice.
Jenco Instruments, Inc.
7968 Arjons Drive, Suite C
San Diego, CA 92126 USA
TEL: [phone]
FAX: [phone]
E-Mail: [email protected]; [email protected]
Website: www.JENCOi.com
Jenco Electronics, Ltd.
6F., NO. 81, Sec.2, Chang-an E. Rd., Jhongshan District, Taipei
City 104, Taiwan
TEL: [phone]
FAX: [phone]
E-Mail: [email protected]
Website: www.JENCO.com.tw
Shanghai Jenco Instruments, Ltd.
18 Wang Dong Zhong Road
Sijing Town, Songjiang
Shanghai, China 201601
TEL: [phone]
FAX: [phone]
E-Mail: [email protected]
Website: www.JENCO.com.cn