Jetson Quest User manual

QUEST
ELECTRIC FOLDING SCOOTER

TABLE OF CONTENTS
What’s in the Box 1
Features & Specs 2
Assembling the Handlebar 3
Assembling the Handles 4
Charging the Battery 5
Unfolding the Quest 6
Operating the Quest 7
Battery Indicator 8
Speed Settings 9
Riding the Quest 10
Using the Thumb Throttle 11
Using the Handbrake 12
Adjusting the Handbrake 13
Using the Kickstand 14
Folding the Quest 15
Connecting to Bluetooth® 16
Care and Maintenance 17
Safety Warnings 18

1. WHAT’S IN THE BOX
1
3
5
7
8
10 11
1. FRONT TIRE
2. HANDBRAKE
3. HANDLEBAR
4. RELEASE LEVER
5. DECK
6. REAR FENDER
7. REAR TIRE
8. KICKSTAND
9. SMALL SCREW (X4)
10. CHARGER
11. CHARGING CABLE
4
2
6
Please Note: Illustrations may not reflect exact appearance of actual product.
9

2. FEATURES & SPECS
• Product Dimensions: 47.24” (L) x 21.65” (W) x 46.45” (H)
• Weight Limit: 220 lbs.
• Product Weight: 28.4 lbs.
• Recommended Age: +13
• Tire Size: 8.5”
• Max Speed: Up To 15 mph
• Max Range: Up To 18 Miles
• Battery: 36V, 7.5Ah Lithium-Ion
• Motor: 500W Hub Motor
• Charger: 100-240V
• Charge Time: Up To 6 Hours
• Climbing Angle: Up To 15°
• Frame Material: Aluminum Alloy
QUEST

3. ASSEMBLING THE HANDLEBAR
Slide Handlebar
into Stem Tube
Tighten using
the 4 small
screws
Make sure the screws are tight and the Handlebar is secure.

4. ASSEMBLING THE HANDLES
Connecting the Handles:
• Starting on the rider left side, take one handle and twist it
towards the rider 3-4 times until it catches. If it does not catch,
try the other handle on the same side. Tighten until the handle
no longer turns.
• Repeat on the rider right side by twisting the handle towards
the rider until it no longer turns.

5. CHARGING THE BATTERY
A few must-do’s:
• Only use the included charger
• Plug the charger into the wall before the Charging Port
• Don’t turn on the Quest while it’s charging (it needs its rest)
• Charge the battery until it is fully charged - up to 6 hours
• Replace the cover over the Charging Port when done
• Remember to have fun!
CHARGING INDICATOR ON THE CHARGER:
Red Light: Battery is charging
Green Light: Charging is complete
Charging Port

6. UNFOLDING THE QUEST
6.1
6.2 6.3
Unclip
Unclip the Handlebar from
the Rear Fender
Lift Handlebars away from Deck Close the Release Lever by lifting it
up until it clicks
Release
Lever

6.4 6.5
Make sure the Release Lever and
Handlebars are secure.
6.6
Lock the Release Lever
Turn to
lock

7. OPERATING THE QUEST
LED Display
• Powering On/Off - Hold the Power Button for 3 seconds to turn the Quest
on or off.
• LED Display - Shows current speed, speed mode, and battery life
remaining.
• Light Function - Once the Quest is on, press the Power Button twice to
turn on the headlight and taillight. The light symbol will show on the LED
Display.
• Odometer - Press the Power Button 3 times to show the Odometer. Press
it another 3 times to return to the Speedometer.
Power
Button

8. BATTERY INDICATOR
BATTERY LEVELS:
• 5 Lights - 81-100% Power
• 4 Lights - 61-80% Power
• 3 Lights - 41-60% Power
• 2 Lights - 21-40% Power
• 1 Light - 1-20% Power (please charge the Quest immediately!)
Battery
Indicator

9. SPEED SETTINGS
Press the Power Button once to cycle through the speed settings.
• 1 - Max speed up to 4 mph
• 2 - Max speed up to 8 mph
• 3 - Max speed up to 15 mph
Speed mode

10. RIDING THE QUEST
• Place one foot in front.
• Place the other foot in back, at a 70-90° angle.
• Turn the handlebar to the left or right to make turns.

11. USING THE THUMB THROTTLE
Quick Note: The Quest is motion activated, you will need
to push forward with one foot before using the Thumb
Throttle. Also, please try to take it easy on the throttle
until you get used to it.

12. USING THE HANDBRAKE
Quick Note: Squeeze the Handbrake slowly to avoid stopping
abruptly or losing control.

13. ADJUSTING THE HANDBRAKE
BRAKE ADJUSTMENT
• Twist the barrel adjuster counterclockwise about a quarter to half turn
to tighten the brake.
• Twist the barrel adjuster clockwise about a quarter to half turn to
loosen the brake.
• Please test the brake again before riding.
Twist
Barrel
Adjuster
Hold nut in
place

14. USING THE KICKSTAND
14.1
14.2

15. FOLDING THE QUEST
Release
Lever
15.1
15.2 15.3
Unlock the Release Lever
Turn to
unlock
Lower the the Release Lever

15.4 15.5
Connect the hook to the Rear
Fender
Lower the Handlebar towards
the Deck
15.6

16. CONNECTING TO BLUETOOTH®
Your Jetson Quest is Bluetooth® 4.0 enabled, so you can pair it with the
Ride Jetson app on your personal Bluetooth® enabled device. The Ride Jetson
app is available for download from the App Store and the Google Play Store,
and it’s free!
1. Turn on the Quest.
2. Open the Ride Jetson app on your handheld device.
3. Tap the Bluetooth® symbol in the top left corner of the app. (If you have not
activated your Bluetooth® on your handheld device, the app will remind you).
4. Select your Quest.
5. The default Bluetooth password is 000000. If you would like to customize your
password, go to the Settings in the app.
If you are having issues connecting to Bluetooth®, follow these steps…
1. Try restarting the Quest by turning it off and then on.
2. Click the Scan button to refresh.
3. Restart the Ride Jetson app.
4. Contact Jetson Customer Support for assistance.
Extra features available with the Ride Jetson app:
• Turn your Headlight on or off.
• Keep track of your travel time and distance.