JETWAY NF695C6-3455 Series User manual

NF695C6-3455 Series
User’s Manual
NO. G03-NF695C6-F
Revision: 1.0
Release date: September 15, 2020
Trademark:
* Specifications and Information contained in this documentation are furnished for information use only, and are
subject to change at any time without notice, and should not be construed as a commitment by manufacturer.

ii
Environmental Protection Announcement
Do not dispose this electronic device into the trash while discarding. To minimize
pollution and ensure environment protection of mother earth, please recycle.

iii
ENVIRONMENTAL SAFETY INSTRUCTION...........................................................................iv
USER’S NOTICE .......................................................................................................................v
MANUAL REVISION INFORMATION.......................................................................................v
ITEM CHECKLIST.....................................................................................................................v
CHAPTER 1 INTRODUCTION OF THE MOTHERBOARD
1-1 FEATURE OF MOTHERBOARD................................................................................1
1-2 SPECIFICATION.........................................................................................................2
1-3 LAYOUT DIAGRAM....................................................................................................3
CHAPTER 2 HARDWARE INSTALLATION
2-1 JUMPER SETTING .....................................................................................................8
2-2 CONNECTORS AND HEADERS................................................................................13
2-2-1 CONNECTORS .............................................................................................13
2-2-2 HEADERS .....................................................................................................16
CHAPTER 3 INTRODUCING BIOS
3-1 ENTERING SETUP .....................................................................................................24
3-2 BIOS MENU SCREEN ................................................................................................25
3-3 FUNCTION KEYS .......................................................................................................26
3-4 GETTING HELP ..........................................................................................................26
3-5 MEMU BARS ..............................................................................................................26
3-6 MAIN MENU................................................................................................................27
3-7 ADVANCED MENU.....................................................................................................28
3-8 CHIPSET MENU .........................................................................................................40
3-9 SECURITY MENU.......................................................................................................43
3-10 BOOT MENU...............................................................................................................45
3-11 SAVE & EXIT MENU...................................................................................................46
TABLE OF CONTENT

iv
Environmental Safety Instruction
Avoid the dusty, humidity and temperature extremes. Do not place the product in
any area where it may become wet.
0 to 60 centigrade is the suitable temperature. (The figure comes from the request
of the main chipset)
Generally speaking, dramatic changes in temperature may lead to contact
malfunction and crackles due to constant thermal expansion and contraction from
the welding spots’ that connect components and PCB. Computer should go
through an adaptive phase before it boots when it is moved from a cold
environment to a warmer one to avoid condensation phenomenon. These water
drops attached on PCB or the surface of the components can bring about
phenomena as minor as computer instability resulted from corrosion and oxidation
from components and PCB or as major as short circuit that can burn the
components. Suggest starting the computer until the temperature goes up.
The increasing temperature of the capacitor may decrease the life of computer.
Using the close case may decrease the life of other device because the higher
temperature in the inner of the case.
Attention to the heat sink when you over-clocking. The higher temperature may
decrease the life of the device and burned the capacitor.

v
USER’S NOTICE
COPYRIGHT OF THIS MANUAL BELONGS TO THE MANUFACTURER. NO PART OF THIS MANUAL,
INCLUDING THE PRODUCTS AND SOFTWARE DESCRIBED IN IT MAY BE REPRODUCED, TRANSMITTED
OR TRANSLATED INTO ANY LANGUAGE IN ANY FORM OR BY ANY MEANS WITHOUT WRITTEN
PERMISSION OF THE MANUFACTURER.
THIS MANUAL CONTAINS ALL INFORMATION REQUIRED TO USE THIS MOTHER-BOARD SERIES AND WE
DO ASSURE THIS MANUAL MEETS USER’S REQUIREMENT BUT WILL CHANGE, CORRECT ANY TIME
WITHOUT NOTICE. MANUFACTURER PROVIDES THIS MANUAL “AS IS” WITHOUT WARRANTY OF ANY
KIND, AND WILL NOT BE LIABLE FOR ANY INDIRECT, SPECIAL, INCIDENTIAL OR CONSEQUENTIAL
DAMAGES (INCLUDING DAMANGES FOR LOSS OF PROFIT, LOSS OF BUSINESS, LOSS OF USE OF
DATA, INTERRUPTION OF BUSINESS AND THE LIKE).
PRODUCTS AND CORPORATE NAMES APPEARING IN THIS MANUAL MAY OR MAY NOT BE
REGISTERED TRADEMARKS OR COPYRIGHTS OF THEIR RESPECTIVE COMPANIES, AND THEY ARE
USED ONLY FOR IDENTIFICATION OR EXPLANATION AND TO THE OWNER’S BENEFIT, WITHOUT
INTENT TO INFRINGE.
Manual Revision Information
Reversion Revision History Date
1.0 First Edition September 15, 2020
Item Checklist
Motherboard
Cable(s)

1
Chapter 1
Introduction of the Motherboard
1-1 Feature of Motherboard
Intel®Apollo Lake series SoC Processor, with low power consumption never
denies high performance
1 * SO-DIMM slot supports 1* 1867 MHz DDR3L SO-DIMM, up to 8GB
Realtek ALC662 Audio
2*10/100/1000 based-TX ethernet ports
Onboard 1* SATAIII port &1* M.2 Socket 3 slot for M-Key type 2242/2260 SATA
SSD
Support HDMI/LVDS or eDP multiple-display solution
Support 6 * COM port expansion
4 * External USB 3.0 & 6 * Internal USB 2.0
Onboard 1* full-size Mini-PCIE slot & 1* SIM card slot
1 * Internal PS2 Keyboard & Mouse pin header
Compliance with ErP standard
Support Watchdog function
Support TPM function (optional)
Solution for Digital Signage, POS & Industrial Automation

2
1-2 Specification
Spec
Description
Design
Mini-ITX form factor; PCB size: 17.0x17.0cm
CPU
Intel®Apollo Lake *SoC CPU
*CPU model varies from different IPC options. Please consult your
dealer for more information of onboard CPU.
Memory
1*DDR3L SO-DIMM slot
Support DDR3L 1867 MHz SO-DIMM up to 8GB
Expansion Slot
1* full-size Mini-PCIE slot (MPE1)
1* SIM card slot (SIMCARD)
Storage
1* SATAIII 6Gb/s port
1* M.2 Socket 3 slot (M2, M-key, support type-2242 /2260SATA
SSD)
LAN Chip
2* RTL8111H GbE
Support Fast Ethernet LAN function of providing
10/100/1000Mbps Ethernet data transfer rate
Audio Chip
Realtek ALC662 HD Audio Codec integrated
Audio driver and utility included
BIOS
AMI Flash ROM
Rear I/O
1* DCIN (12V) JACK
2 * RJ-45 LAN port
2 * HDMI port
4* USB3.0 port
1* Line-out port
Internal I/O
1* Front panel header
3* 9-pin USB 2.0 header
2* 9-pin Serial port header (COM1/2)
1* Serial port header expansion block (COM3-6)
2* LAN activity LED header

3
1* PS2 Keyboard /Mouse header
1* Front panel audio header
1* 10-pin GPIO header
1*SMBUS header
1* front panel buzzer header
1* LVDS header (Selectable with EDP)
1*1* EDP header (Selectable with LVDS)
1* LVDS/EDP inverter header
Note: 1.The module should be DDR3L 1.35V SODIMM and not exceeding 8GB total capacity.
2. The SODIMM installed should be of or above the memory clock the model supported, otherwise the
board will not start.
1-3 Layout Diagram
Rear IO Panel Diagram:
Warning!! The board has a 12V DC-in power connector (DCIN1) in I/O back panel and an
internal 12V power connector (DCIN2). User can only connect one type of compatible power
supply to one of them to power the system.
DCIN
HDMI2
Port
LAN1 RJ-
45
LAN Port
LAN2
RJ-45
LAN Port
HDMI1
Port
USB 3.0
Ports
Line-out

4
Motherboard Internal Diagram
Note: SIMCARD slot only work when compatible SIM card installed & 3G LAN card installed in full-size Mini-PCIE (MPE1) slot.
*Rear IO
Connector
(Refer to Page-3)
DDR3L Slot
(SODIMM1)
SATA Power-out
Connector
Full-size
Mini-PCIE Slot
(MPE1)
M.2 Socket 3 Slot
(M2)
*SIMCARD Slot
EDP
USB 2.0 Ports
Front Panel
Header
*Serial Port Header Block
(COM3-6)
Serial Port Headers
(COM1/COM2)
Front Panel
Audio Header
PS/2 Keyboard & Mouse
Header
Inverter
LVDS
SATAIII Port
FP_BUZZ
Header
CPUFAN
SMBUS Header
SYSFAN
GPIO Port
Header
Internal 12V
DC-in Connector
LAN1_LED Header
LAN2_LED Header

5
Jumper Positions:
JP2
JMD1
JMD2
JMD3
JP1
ATX_AT
JP4
JP3

6
Jumper
Jumper
Name
Description
JMD1
COM1 Serial Port Power Select
4-pin Block
JMD2
COM2 Serial Port Power Select
4-pin Block
JMD3
COM3 Serial Port Power Select
4-pin Block
JP1
MINIPCIE Power 3VSB / 3.3V Select
3-Pin Block
ATX_AT
ATX Mode / AT Mode Select
3-Pin Block
JP4
LVDS/EDP Inverter Power 3.3V/5V/12V Select
3-pin Block
JP3
LVDS/EDP Panel Power 3.3V/5V/12V Select
4-pin Block
JP2
Pin 1&2：CASE OPEN
Pin 3&4：TXE Override
Pin 5&6：Clear CMOS
Pin 7&8：Clear ME_RTC
8-pin Block
Connectors
Connector
Name
DCIN1
12V DC input Power Jack
HDMI2
HDMI Port Connector
LAN1
RJ-45 LAN Port Connector
LAN2
RJ-45 LAN Port Connector
HDMI1
HDMI Connector
USB31
USB3.0 Port Connector
USB32
USB3.0 Port Connector
FP_HP
Audio Line-out Port Connector
DCIN2
Internal 12V DC-in Power Connector
SATA1
SATAIII Port Connector
SATAPW
SATA Power Connector
CPUFAN
CPU Fan Connector
SYSFAN
System Fan Connector

7
Headers
Header
Name
Description
FP
Front Panel Header
(PWR LED/ HDD LED/
Power Button /Reset)
9-pin Block
F_USB1/ F_USB2/
F_USB3
USB 2.0 Header
9-pin Block
COM1
RS232 Serial Port Header
9-pin Block
COM2
RS232 Serial Port Header
9-pin Block
COM3-6
RS232 Serial Port Combo Block
36-pin Block
LAN1_LED
LAN Activity LED Header
2-pin Block
LAN2_LED
LAN Activity LED Header
2-pin Block
PS2KBMS
PS2 keyboard & Mouse
6-pin Block
FP_AUDIO
Front Panel Audio Header
9-pin Block
GPIO
GPIO Port Header
10-pin Block
SMBUS
SMBUS Header
5-pin Block
FP_BUZZ
Buzzer Header
2-pin Block
INVERTER
LVDS INVERTER Header
8-pin Block
EDP
EDP Wafer
40-pin Block
LVDS
LVDS Header
32-pin Block

8
Chapter 2
Hardware Installation
2-1 Jumper Setting
(1) JMD1 (4-pin): COM1 Port Pin9 Function Select
JMD1 → COM1 Port Pin-9
6
4
2
3
1
5
5
3
1
2
4
6
1
3
5
2
4
6
2-4 Closed:
RING( Default);
3-4 Closed:
5V;
4-6 Closed:
12V.
(2) JMD2 (4-pin): COM2 Header Pin9 Function Select
JMD2 → COM2 Header Pin-9
6
4
2
3
1
5
1
3
5
2
4
6
1
3
5
2
4
6
2-4 Closed:
RING( Default);
3-4 Closed:
5V;
4-6 Closed:
12V.
JMD1
JMD2

9
(3) JMD3 (4-pin): COM3 Header Pin9 Function Select
1
3
4
6
2
6
4
2
5
3
1
6
4
2
5
3
1
5
JMD3 → COM3 Header Pin-9
2-4 Closed:
RING( Default);
3-4 Closed:
5V;
4-6 Closed:
12V.
(4) JP1 (3-pin): MINIPCIE SLOT POWER VCC3.3V / 3VSB Select
1
3
1
3
JP1 → MPE1 Power VCC Select
1-2 Closed: MPE1 VCC=3.3V(Default);
;
2-3 Closed: MPE VCC=3VSB.
JMD3
JP1

10
(5) ATX_AT (3-pin): AT/ATX Mode Select
1
3
1
3
ATX_AT → ATX/AT Mode Select
1-2 Closed: ATX Mode (Default);
;
2-3 Closed: AT Mode.
*ATX Mode Selected: Press power button to power on after power input ready;
AT Mode Selected: Directly power on as power input ready.
(6) JP4 (3-pin): LVDS / EDP Inverter Backlight VCC 5V/12V Select
1
3
1
3
JP4 → LVDS Panel VCC Select
1-2 Closed: VCC=5V (Default);
;
2-3 Closed: VCC=12V.
ATX_AT
JP4

11
(7) JP3 (4-pin): LVDS / EDP Panel VCC 3.3V/5V/12V Select
JP3 → LVDS Panel VCC
4-6 Closed:
VCC= 12V.
6
5
1
4
3
2
1
5
3-4 Closed:
VCC= 5V;
2-4 Closed:
VCC=3.3V
(Default);
3
4
1
2
6
5
6
2
6
5
1
4
3
2
1
5
1
2
6
3
4
5
2
6
5
1
4
3
2
1
5
1
2
6
3
4
5
2
(8) JP2 (8-pin): Jumper Combo Block
Pin 1&2 of JP2 (8-pin): Case Open Message Display Function Select
1-2 Open:
Normal (Default);
1
1-2 Closed:
Case Open.
1
2
2
Pin (1-2) Close: When Case Open function pin short to GND, the Case Open function
was detected. When Used, needs to enter BIOS and enable ‘Case Open Detect’
function. In this case if your case is removed, next time when you restart your
computer, a message will be displayed on screen to inform you of this.
JP2
JP3

12
Pin 3&4 of JP2 (8-pin): TXE Override Setting
3-4 Open：
Normal (Default);
1
3-4 Closed：
TXE Override.
1
2
2
3
4
3
4
Pin 5&6 of JP2 (8-pin):CLEAR CMOS
5-6 Open:
Normal (Default);
1
5-6 Closed:
Clear CMOS.
1
2
2
3
4
5
6
3
4
5
6
Pin 7&8 of JP2 (8-pin): Clear ME_RTC
7-8 Open：
Normal (Default);
1
7-8 Closed：
Clear ME_RTC.
1
2
2
3
4
5
4
6
7
8
3
5
7
4
6
8
JP2
JP2
JP2

13
2-2 Connectors and Headers
2-2-1 Connectors
(1) Rear I/O Connectors
*Refer to Page-3.
Icon
Name
Function
Power Jack
12V DC–in system power connector
For user to connect compatible power adapter to
provide power supply for the system.
HDMI Port
To connect display device that support HDMI
specification.
RJ-45 LAN Port
This connector is standard RJ-45 LAN jack for
Network connection.
USB 3.0 Port
To connect USB keyboard, mouse or other
devices compatible with USB specification. USB
3.0 ports supports up to 5Gbps data transfer rate.
Line-Out
This connector can functions as audio Line-Out
jack and MIC jack with compatible cables &
devices.

14
(2) DCIN2 (2-pin): Internal 12V DC-in power connector
Pin No.
Definition
1
+12V DC_IN
2
GND
Pin1
Warning! The board has a 12V DC-in power connector (DCIN1) in I/O back panel and an
internal 12V power connector (DCIN2). User can only connect one type of compatible power
supply to one of them to power the system.
(3) SATA1 (7-pin block):SATAIII Port connector
This connector is a high-speed SATAIII port that supports 6 GB/s transfer rate.
Pin No.
Definition
1
GND
2
TXP
3
TXN
4
GND
5
RXN
6
RXP
7
GND
DCIN2
SATA1

15
(4) SATAPW (4-pin) : SATA Power-out Connector
Pin 1
+12V
+5V
GND
GND
(5) CPUFAN (4-pin): CPU FAN Connector
Pin1
GND
+12V Fan Power
Fan Speed
Control
(6) SYSFAN (4-pin): FAN Connector
Pin1
GND
+12V Fan Power
Fan Speed
Control
SATAPW
CPUFAN
SYSFAN