Jmaz Lighting HALO Q4 STROBE User manual

HALO Q4 STROBE
User manual
Please read this user manual before using this product

1. Checking before using
No.
Item
Quan
tity
Unit
1
PAR Light
1
piece
2
Power cable with blue head
1
piece
3
User manual
1
piece
★For security reasons and in accordance with the terms, reassemble or modify the product is not allowed without
permission. Please note that due to human damage caused by improper use of the product, it will break the
warranty qualification. Moreover, the unprofessional operation may lead to short circuits, burns or electric shock,
and so on.
★This device has been full inspection before shipping. For your safety, please operate it according the User
Manual.
★If any damage caused by improper operation will result in the termination of the warranty claims. The
manufacturer does not accept any responsibility of property damage due to improper operation or personal injury
due to non-compliance with the operating instructions.
★Keep the manual in a safe place for future reference as well as after the product sale, lease, etc.
★Note: Based on product improvements, specification may change without notice. Changes in product
specifications related rights will be reserved.
2. Safety Instruction
1. When opening the packing, take all accessories out, and remove the light to a horizontal table for good
operation. First check whether the accessories are complete, then check carefully whether the whole light has no
damage. If there is any damage, please contact us as soon as possible.
2. AC Power: Check whether the local power supply is accordance with the
requirements of the product rated voltage.
3. The product is only suitable for indoor working environment. The light should
keep dry, keep away from wet, overheat or dusty environment. Don't come into contact with water and other
liquids to prevent or reduce the risk of electric shock or fire.

4. Please do not install the light directly on the surface of the combustible substance.
5. The people who install, operate and maintain of light professional certificate required.
6. When there are faults of the light, please stop using the light immediately. Don't try to repair, please contact the
nearest authorized technical assistance center, if the parts damage, always use the same type of parts replaced.
7. Don't touch any electrical wiring in the process of operation to prevent the risk of electric shock.
8. To make sure the light working environment temperature, the highest do not exceed 40℃, the lowest do not
exceed - 20 ℃.
9. Under the stable cooling working situation, the highest temperature of the housing of the light can reach 80 ℃,
please do not touch.
10. The light is design according to the type of electric shock protection. The light should be use in good
connection grounding power system and the earth sign port of the light should be connected to the installing
fixtures.
11. Do not use the damage of the insulating layer wire and also do not use the power cord overlap on the other
wire. When not in use or clean the light, please disconnect the power, don't pull the plug in hard or just drag the
wires.
12. There are no components inside for maintenance. Before start operation the light, please check whether all of
the shell is installed. In the case of the shell open used the light is prohibited.
Note: Before performing any installation, repair and cleaning of the lamp, please confirm that the
power cable has been cut off.
3. Product specification
1. Voltage: AC100-240V 50-60Hz
2. Power Consumption: 200W
3. Light Source: 921 ×SMD505 4in1 LEDs
4. Beam Angle: 120°
5. Source life: 100,000 hours

6. Color: 1670 million kinds of colors
7. Working modes: Sound (Audio)Active, Show Mode, DMX, Master/ Slave.
8. Powercon: Input / Output
9. DMX Channel: 4CH/7CH/40CH
10. W: 5KG
11.Size: 42 x 19 x 38cm
4. Display Main function:
Interface
Function
Remark
D001
DMX NO
D001-D512
TEMP
Err’C
Temp of Light
Press 5 seconds to enter the background to set whether the
digital tube enters the sleep mode
CH-Mode
06/09/36/41CH
Selection of DMX Channel mode
CH: 01
000
01- 36
000-255
Brightness of Ring control adjustment under 36CH mode
R DIM
000
000-255
Red Dimming
G DIM
000
000-255
Green Dimming
B DIM
000
000-255
Blue Dimming
W DIM
000
000-255
White Dimming

Strobe
000
000-100
Strobe from slow to fast
Pro:00
Spd: 00
00-15
00-25
Pro: Selection of built-in 15 program
Spd: 0-19 speed from slow to fast. 20-25 Sound mode ON,
Sensitivity from Low to High. Without this menu in 6CH mode.
Color
00-15
Color: Selection of 15 colors
Without this menu in 6CH mode.
Reset
OFF
ON-OFF
5. LCD Display Function Instruction
6. DMX 512 Channel-6CH
Ch
Function
Value
Description
1CH
Master Dimmer
0
NO