John deer S760 User manual

S760, S770, S780, and S790

Combines (S.N. 800001— )

*OMHXE122584*

OPERATOR'S MANUAL

S760, S770, S780, and S790 Combines

OMHXE122584 ISSUE G7 (ENGLISH)

CALIFORNIA

Proposition 65 Warning

Diesel engine exhaust and some of its constituents

are known to the State of California to cause cancer,

birth defects, and other reproductive harm.

If this product contains a gasoline engine:

WARNING

The engine exhaust from this product contains

chemicals known to the State of California to cause

cancer, birth defects or other reproductive harm.

The State of California requires the above two warnings.

Additional Proposition 65 Warnings can be found in this manual.

John Deere Harvester Works

North American Edition

PRINTED IN U.S.A.

*DCY**OMHXE122584*

Introduction

DX,IFC1 -19-03APR09-1/1

Foreword

READ THIS MANUAL carefully to learn how to operate

and service your machine correctly. Failure to do so

could result in personal injury or equipment damage.

This manual and safety signs on your machine may also

be available in other languages. (See your John Deere

dealer to order.)

THIS MANUAL SHOULD BE CONSIDERED a permanent

part of your machine and should remain with the machine

when you sell it.

MEASUREMENTS in this manual are given in both

metric and customary U.S. unit equivalents. Use only

correct replacement parts and fasteners. Metric and inch

fasteners may require a specific metric or inch wrench.

RIGHT-HAND AND LEFT-HAND sides are determined by

facing in the direction of forward travel.

WRITE PRODUCT IDENTIFICATION NUMBERS (P.I.N.)

in the Specification or Identification Numbers section.

Accurately record all the numbers to help in tracing the

machine should it be stolen. Your dealer also needs these

numbers when you order parts. File the identification

numbers in a secure place off the machine.

WARRANTY is provided as part of John Deere's support

program for customers who operate and maintain their

equipment as described in this manual. The warranty is

explained on the warranty certificate or statement which

you should have received from your dealer.

This warranty provides you the assurance that John

Deere will back its products where defects appear within

the warranty period. In some circumstances, John Deere

also provides field improvements, often without charge

to the customer, even if the product is out of warranty.

Should the equipment be abused, or modified to change

its performance beyond the original factory specifications,

the warranty will become void and field improvements

may be denied. Setting fuel delivery above specifications

or otherwise overpowering machines will result in such

action.

THE TIRE MANUFACTURER'S warranty supplied with

your machine may not apply outside the U.S.

If you are not the original owner of this machine, it is in

your interest to contact your local John Deere dealer to

inform them of this unit's serial number. This will help John

Deere notify you of any issues or product improvements.

070717

PN=2

Find manuals at https://best-manuals.com

Introduction

SS43267,00005E9 -19-12MAY15-1/1

Identification View

H113914 —UN—12MAY15

Grain Tank Extension

H113915 —UN—12MAY15

Grain Tank Cover

070717

PN=3

Find manuals at https://best-manuals.com

Introduction

070717

PN=4

Find manuals at https://best-manuals.com

Contents

Page

Safety Features

Machine Safety Features....................................05-1

Safety

Recognize Safety Information ............................10-1

Understand Signal Words...................................10-1

Follow Safety Instructions...................................10-1

Spanish Safety Signs and Operator's Manual....10-2

Driving the Machine............................................10-2

Keep Riders and Children Off Machine..............10-2

Ballasting for Safe Ground Contact....................10-3

Avoid Electrical Power Lines ..............................10-3

Parking and Leaving the Machine ......................10-3

Work In Ventilated Area......................................10-4

Handle Fuel Safely—Avoid Fires........................10-4

Prepare for Emergencies....................................10-4

Handle Starting Fluid Safely...............................10-5

In Case of Fire....................................................10-5

Avoid Static Electricity Risk When Refueling......10-6

Wear Protective Clothing....................................10-6

Stay Clear of Harvesting Units ...........................10-6

Keep Hands Away From Knives.........................10-7

Use Safety Lights and Devices...........................10-7

Use Seat Belts....................................................10-7

Instructional Seat................................................10-8

Transport Combine With Header Safely.............10-8

Prevent Machine Runaway or

Unexpected Movement ..................................10-8

Practice Safe Maintenance.................................10-9

Welding Near Electronic Control Units ...............10-9

Remove Paint Before Welding or Heating........10-10

Avoid Heating Near Pressurized Fluid Lines....10-10

Avoid Contact With Moving Parts.....................10-10

Cleaning Grain Tank and Removal of

Blockages Safely.......................................... 10-11

Stay Clear of Rotating Drivelines...................... 10-11

Install All Shields and Guards........................... 10-11

Avoid High-Pressure Fluids..............................10-12

Do Not Open High-Pressure Fuel System........10-12

Service Accumulator Systems Safely...............10-12

Protect Against High Pressure Spray...............10-13

Follow Tire Recommendations .........................10-13

Service Tires Safely..........................................10-13

Decommissioning — Proper Recycling

and Disposal of Fluids and Components .....10-14

Service Cooling System Safely ........................10-14

Remove Accumulated Crop Debris ..................10-15

Page

Support Machine Properly................................10-15

Store Attachments Safely.................................10-15

Service Drive Belts Safely ................................10-16

Handle Electronic Components and

Brackets Safely ............................................10-16

Avoid Backover Accidents................................10-16

Emergency Exit ................................................10-17

Handling Batteries Safely .................................10-17

Clean Exhaust Filter Safely ..............................10-18

Avoid Hot Exhaust............................................10-18

Rotational Alarm System..................................10-19

Operator Presence System ..............................10-19

Safety Signs

Front View Decals ..............................................15-1

Feeder House Left-Hand Decals........................15-2

Cab Decals and Ladder Decals..........................15-3

Left-Hand View Decals.......................................15-4

Left-Hand View Decals Continued......................15-5

Left-Hand View Decals Continued......................15-6

Left-Hand View Residue Decals.........................15-7

Rear View Decals and Engine View Decals .......15-8

Rear View Decals and Engine View

Decals Continued...........................................15-9

Right-Hand View Residue Decals ....................15-10

Right-Hand View Decals................................... 15-11

Right-Hand View Decals Continued .................15-12

Feeder House Right-Hand View Decals...........15-13

Top View Decals ...............................................15-14

Top View Decals Continued..............................15-15

Replace Safety Signs .......................................15-16

Operator’s Station

Radio Types (Optional).......................................20-1

After Market Radios............................................20-1

Program Radio for Local Area Frequency..........20-1

Radio Controls....................................................20-2

Antenna ..............................................................20-2

Communications/CB Radio Mounting.................20-3

Cab Ladder Positions .........................................20-5

Fire Extinguishers...............................................20-6

Fire Extinguisher Locations ................................20-6

Handrails and Right-Hand Landing Access........20-7

Break-In Service

Breaking-In Engine.............................................25-1

Continued on next page

Original Instructions. All information, illustrations and specifications in this

manual are based on the latest information available at the time of publication.

The right is reserved to make changes at any time without notice.

DEERE & COMPANY

Moline, Illinois

A John Deere ILLUSTRUCTION ™ Manual

i070717

PN=1

Find manuals at https://best-manuals.com

Contents

Page

Belt Drives Adjustment - First 50 Hours .............25-3

Break-In Check Before First 100 Hours..............25-4

Break-In Service After 100 Hours (Tier

2/Stage II and Tier 3/Stage IIIA).....................25-4

Break-In Service After 400 Hours (Final

Tier 4/Stage IV) ..............................................25-5

Prestarting Checks

Engine Oil Level .................................................30-1

Hydrostatic/Hydraulic Oil Level...........................30-2

Coolant Level......................................................30-2

Fuel System........................................................30-3

Fuel Tank Breather .............................................30-4

Diesel Exhaust Fluid (DEF) Tank

Breather (Final Tier 4/Stage IV) .....................30-5

Engine Air Scoop Positions ................................30-5

Position Engine Air Scoop (Standard

Field Position) ................................................30-6

Position Engine Air Scoop (Extended

Field Position) ................................................30-7

Position Engine Air Scoop (Transport Position) ..30-8

Cleaning Engine Compartment ..........................30-9

Operating the Engine

Clean Exhaust Filter Safely ................................35-1

Avoid Hot Exhaust..............................................35-1

Qualified Emergency Use — SCR

Override Option..............................................35-2

Required Machine Stop Warning........................35-3

Object Detection Sensor (Final Tier

4/Stage IV) .....................................................35-4

Starting the Engine.............................................35-4

Stopping the Engine ...........................................35-6

Engine Speed Management

(ProDrive™ Machines)...................................35-6

Handle Starting Fluid Safely...............................35-7

Cold Weather Starting Aid (If Equipped) ............35-7

Coolant Heater ...................................................35-8

CommandCenter™ Display Information

Onscreen Help....................................................40-1

Generation 4 CommandCenter™.......................40-1

Generation 4 CommandCenter™ Processor......40-2

Run Page Structure............................................40-3

Status Center......................................................40-3

Shortcut Softkeys ...............................................40-4

Menu...................................................................40-4

Operating System Applications Overview ..........40-4

AMS Applications Overview ...............................40-9

CommandCenter™ Premium Activation...........40-10

Demo Activations..............................................40-10

Display and Sound ...........................................40-10

Brightness......................................................... 40-11

Sound ............................................................... 40-11

Multiple Displays...............................................40-12

Display Calibration............................................40-14

Date and Time ..................................................40-14

Page

Change Current Date .......................................40-15

Change Current Time .......................................40-15

Language and Units .........................................40-15

Language and Units Settings ...........................40-16

Software Manager ............................................40-16

Update Display Software..................................40-17

Activations ........................................................40-18

Service ADVISOR™ Remote ...........................40-19

Vehicle Reprogramming ...................................40-20

Troubleshooting — Reprogramming ................40-23

File Manager.....................................................40-23

USB Drive.........................................................40-26

Capture Screen Shots ......................................40-26

Diagnostics Center ...........................................40-27

Controller Diagnostics ......................................40-27

Diagnostic Information......................................40-28

Hide Diagnostic Center.....................................40-28

Diagnostic Trouble Codes ................................40-28

Display Hardware .............................................40-29

CAN Bus Information........................................40-30

CAN Bus Values ...............................................40-31

Network ............................................................40-32

Users and Access.............................................40-32

User Profiles.....................................................40-32

Access Groups .................................................40-33

Layout Manager................................................40-33

Active Set .........................................................40-33

Shortcut Bar......................................................40-34

All Run Pages...................................................40-35

Add, Edit, or Duplicate Run Pages...................40-35

Navigate Run Pages on Main Page .................40-36

Fields and Boundaries......................................40-37

Manage Clients, Farms, and Fields..................40-38

Field Boundaries...............................................40-39

AutoTrac™ Guidance .......................................40-40

Equipment Manager .........................................40-40

Machine Profile.................................................40-41

Implement Profile..............................................40-42

Settings Manager .............................................40-43

Machine Monitor...............................................40-43

Work Monitor ....................................................40-43

Work Recording................................................40-44

Maintenance and Calibrations..........................40-44

Service Checks.................................................40-44

Service Intervals...............................................40-44

Calibrations.......................................................40-45

ISOBUS VT ......................................................40-45

StarFire™ GPS Receiver .................................40-46

Video ................................................................40-46

Video Triggers ..................................................40-47

Clean Display ...................................................40-47

System Recovery .............................................40-48

CommandCenter™ Display Applications

CommandCenter™ Display Applications ...........45-1

Continued on next page

ii 070717

PN=2

Find manuals at https://best-manuals.com

Contents

Page

Interactive Combine Adjustment

Access Interactive Combine Adjustment........ 45-A-1

Interactive Combine Adjustment (ICA)

Main Page .................................................. 45-A-1

Session Status................................................ 45-A-3

Select areas to improve.................................. 45-A-4

Harvest Priorities ............................................ 45-A-6

What type of Grain Losses? ........................... 45-A-7

What type of Grain Quality issues? ................ 45-A-8

Straw Quality Issues....................................... 45-A-9

ICA2 Detected Issues..................................... 45-A-9

Excess Tailings ............................................... 45-A-9

ICA is finding recommendations................... 45-A-10

Select "Apply" to have ICA adjust

settings using the shown solution. ........... 45-A-11

Edit Issues.................................................... 45-A-12

ICA is applying the setting adjustment... ...... 45-A-12

Undo all ICA adjustments, start over............ 45-A-13

Recommended Solutions ............................. 45-A-13

ICA is awaiting operator action..................... 45-A-14

Select "Next" to proceed with manual

adjustment................................................ 45-A-16

View Performance ........................................ 45-A-17

Separator Loss ............................................. 45-A-19

Shoe Loss..................................................... 45-A-19

Unthreshed Loss .......................................... 45-A-19

Broken Grain ................................................ 45-A-19

Foreign Material Light................................... 45-A-19

Foreign Material Heavy ................................ 45-A-19

Unthreshed Material ..................................... 45-A-19

Since the last adjustment, how has

performance been impacted? .................. 45-A-20

ICA Session Complete ................................. 45-A-22

How should ICA proceed?............................ 45-A-23

ICA is monitoring performance changes... ... 45-A-24

Progress ....................................................... 45-A-25

Controls Setup

Access Controls Setup ................................... 45-B-1

Controls Setup Overview................................ 45-B-1

Multi-Function Lever - Controls Setup............ 45-B-2

Multi-Function Lever....................................... 45-B-3

CommandARM™ - Controls Setup ................ 45-B-5

CommandARM™ ........................................... 45-B-6

Create Single Position Assignments .............. 45-B-7

Create Dual Position Assignments................. 45-B-8

Scroll Button ................................................... 45-B-9

Application Assignments ................................ 45-B-9

Function Assignments .................................. 45-B-10

Residue Management

Access Residue Management........................ 45-C-1

Residue Management .................................... 45-C-1

Residue Mode ................................................ 45-C-4

Separator Vane............................................... 45-C-5

Width .............................................................. 45-C-5

Page

Speed ............................................................. 45-C-6

Direction ......................................................... 45-C-7

Swap............................................................... 45-C-9

Out of Cab Adjustments ................................. 45-C-9

Header

Access Header ............................................... 45-D-1

Header............................................................ 45-D-1

Header Details................................................ 45-D-5

Width .............................................................. 45-D-7

Width Corn Head............................................45-D-7

Row Width ...................................................... 45-D-8

Minimum Reel Speed ..................................... 45-D-9

Work Recording............................................ 45-D-10

Hours............................................................ 45-D-11

Raise/Lower Speed ...................................... 45-D-12

Tilt Speed ..................................................... 45-D-13

Height Sensitivity .......................................... 45-D-14

Tilt Sensitivity................................................ 45-D-16

Fore/Aft Tilt ................................................... 45-D-17

Auto Header Control..................................... 45-D-18

Control Preview ............................................ 45-D-19

Header Automation....................................... 45-D-19

Height Resume............................................. 45-D-20

Height Sensing—Off Ground........................ 45-D-23

Height Sensing—On Ground........................ 45-D-26

Feeder House Float...................................... 45-D-29

Lateral Tilt..................................................... 45-D-31

Resume Preferences.................................... 45-D-32

Dial—A—Speed™........................................ 45-D-33

Fore/Aft Resume .......................................... 45-D-36

Reel Position Resume..................................45-D-37

Deck Plate Position Resume........................ 45-D-39

HydraFlex™ Pressure .................................. 45-D-40

Draper Belt Speed........................................45-D-42

Draper Float Position.................................... 45-D-43

Cutterbar Tilt................................................. 45-D-45

Deck Plate Spacing ...................................... 45-D-46

Backshaft Speed .......................................... 45-D-47

Advanced Settings........................................ 45-D-47

Limp Home Mode ......................................... 45-D-48

HarvestSmart™

Access HarvestSmart™ ................................. 45-E-1

HarvestSmart™ Main Page............................ 45-E-1

Automation ..................................................... 45-E-3

Status ............................................................. 45-E-3

Settings........................................................... 45-E-6

Settings | Operating Mode | Smart Mode ....... 45-E-7

Settings | Operating Mode | Smart

Mode | Smart Target................................... 45-E-8

Settings | Operating Mode | Capacity Mode... 45-E-9

Settings | Operating Mode | Capacity

Mode | Target Pressure.............................. 45-E-9

Settings | Limiters ......................................... 45-E-11

Settings | Limiters | Maximum Engine

Power ....................................................... 45-E-11

Continued on next page

iii 070717

PN=3

Find manuals at https://best-manuals.com

Contents

Page

Settings | Limiters | Maximum Ground

Speed....................................................... 45-E-13

Settings | Response Aggressiveness ........... 45-E-14

Integrated Combine Adjustment 2

Access Integrated Combine

Adjustment 2 .............................................. 45-F-1

Integrated Combine Adjustment 2 Main

Page........................................................... 45-F-1

History | Adjustments...................................... 45-F-4

Optimize Performance.................................... 45-F-5

Adjustment Details.......................................... 45-F-5

Grain System Video........................................ 45-F-7

Edit Harvest Priorities..................................... 45-F-8

History | Performance..................................... 45-F-9

Lens Debris ...................................................45-F-11

ICA2 Cannot Maintain Performance Target...45-F-11

Return to Optimize........................................ 45-F-13

Set Performance Target................................ 45-F-13

History .......................................................... 45-F-14

Active Terrain Adjustment™ ......................... 45-F-14

Uphill Sensitivity ........................................... 45-F-16

Downhill Sensitivity....................................... 45-F-16

Offset Tuning | Cleaning Fan........................ 45-F-17

Offset Tuning | Sieve .................................... 45-F-18

Offset Tuning | Chaffer ................................. 45-F-19

Auto Maintain | Settings................................ 45-F-20

Grain Loss | Sensitivity ................................. 45-F-20

Broken Grain | Sensitivity ............................. 45-F-21

Foreign Material | Sensitivity ........................ 45-F-22

Response aggressiveness ........................... 45-F-23

HarvestSmart™ | Settings ............................ 45-F-24

Target Pressure ............................................ 45-F-25

Maximum Engine Power............................... 45-F-26

Maximum Ground Speed.............................. 45-F-28

Response Aggressiveness........................... 45-F-29

ICA2 Diagnostics.......................................... 45-F-30

Automation Status ........................................ 45-F-31

HarvestSmart™ Status................................. 45-F-32

Active Terrain Adjustment™ Status .............. 45-F-35

Auto Maintain Status .................................... 45-F-37

Grain Handling

Access Grain Handling...................................45-G-1

Grain Handling Main Page .............................45-G-1

Advanced Settings..........................................45-G-3

Advanced Settings | Grain Level Auto

Beacon .......................................................45-G-3

Advanced Settings | Tank Unloading Offset ...45-G-4

Advanced Settings | Custom Level Alarm ......45-G-4

Grain Level .....................................................45-G-5

Moisture Settings............................................45-G-5

Moisture Alarm ...............................................45-G-6

Moisture Correction ........................................45-G-7

Status Center..................................................45-G-8

Page

Folding

Access Folding ............................................... 45-H-1

Folding Main Page.......................................... 45-H-1

Grain Tank Covers.......................................... 45-H-3

Folding Auger Tip ........................................... 45-H-4

Folding Corn Head (Without Position

Sensors)..................................................... 45-H-6

Folding Corn Head (With Position Sensors)... 45-H-7

Harvest Settings

Access Harvest Settings...................................45-I-1

Harvest Settings Main Page.............................45-I-1

Load Harvest Settings ......................................45-I-4

Load Harvest Settings | Preset.........................45-I-5

Load Harvest Settings | Threshing Conditions ..45-I-7

Load Harvest Settings | Straw Conditions ........45-I-8

Load Harvest Settings | Save Preset................45-I-8

Load Harvest Settings | Save Preset |

Factory Default.............................................45-I-9

Load Harvest Settings | Save Preset |

Custom Preset .............................................45-I-9

Load Harvest Settings | Effects of Crop

Change.......................................................45-I-10

Current Settings | Threshing Clearance .........45-I-11

Current Settings | Threshing Speed ...............45-I-12

Current Settings | Cleaning Fan .....................45-I-13

Current Settings | Chaffer Clearance .............45-I-14

Current Settings | Sieve Clearance ................45-I-16

Current Settings | Outside Configuration........45-I-17

Current Settings | Adjustment States .............45-I-17

Advanced Settings..........................................45-I-19

Advanced Settings | Separator Resolution.....45-I-20

Advanced Settings | Shoe Resolution ............45-I-21

Performance Target ........................................45-I-22

Engine

Access Engine.................................................45-J-1

Engine Main Page ...........................................45-J-1

Engine Power ..................................................45-J-3

Exhaust Filter System Overview......................45-J-4

AUTO Exhaust Filter Cleaning ........................45-J-5

Parked Filter Cleaning.....................................45-J-5

Disable AUTO Exhaust Filter Cleaning ...........45-J-7

Engine Cool Down In Progress .......................45-J-8

Debris Management Filter Capacity ................45-J-9

Air Compressor................................................45-J-9

Air Compressor Status ..................................45-J-10

HVAC

Access HVAC ................................................. 45-K-1

Heating, Ventilation, and Air

Conditioning (HVAC) Main Page................ 45-K-1

Set Temperature ............................................. 45-K-3

Fan Speed...................................................... 45-K-4

Air Flow Mode................................................. 45-K-5

Continued on next page

iv 070717

PN=4

Find manuals at https://best-manuals.com

Contents

Page

Air Conditioning (A/C)..................................... 45-K-5

Outside Temperature ...................................... 45-K-5

Transmission

Access Transmission.......................................45-L-1

Transmission Main Page .................................45-L-1

Max Speed 1 and 2 .........................................45-L-3

Advanced Settings ProDrive™........................45-L-3

Advanced Settings ProDrive™ Tow Mode.......45-L-4

Advanced Settings ProDrive™ Limp

Home Mode.................................................45-L-5

Advanced Settings Push Button......................45-L-5

Lights

Access Lights .................................................45-M-1

Lights Main Page............................................45-M-1

Field Lights Preset 1—Low Beam ..................45-M-3

Field Lights Preset 2—Low Beam ..................45-M-3

Field Lights Preset 1—High Beam .................45-M-4

Field Lights Preset 2—High Beam .................45-M-5

Exit Lights.......................................................45-M-6

Field Light Controls.........................................45-M-7

Phone

Pair Bluetooth® Device to Generation

4 CommandCenter™ ................................. 45-N-1

Manage Paired Bluetooth® Devices (If

Equipped)................................................... 45-N-2

Phone Operation ............................................ 45-N-3

Phone Signal Strength and Battery Charge ... 45-N-4

Contact List..................................................... 45-N-5

Recent Calls ................................................... 45-N-6

Clear Favorites and Call History..................... 45-N-7

Calibrations

Access Calibrations and Procedures..............45-O-1

Calibrations and Procedures Overview ..........45-O-1

Mass Flow Vibration .......................................45-O-2

Mass Flow Vibration Calibration Procedure ...45-O-2

Moisture Sensor Temperature ........................45-O-3

Moisture Sensor Temperature Offset..............45-O-3

Threshing Clearance (Standard

Concave Adjust).........................................45-O-5

Threshing Clearance (Standard

Concave Adjust) Calibration Procedure .....45-O-5

Yield Calibration .............................................45-O-6

Yield | Calibration Quality ...............................45-O-7

Yield | Status Indicator....................................45-O-8

Yield | Record Sample....................................45-O-8

Yield | Match Scale Weight...........................45-O-10

Yield | Advanced Settings............................. 45-O-11

Yield | Calibration Quality Indicator...............45-O-12

Yield | Collected Sample Status ...................45-O-13

Yield | Mass Flow Rate.................................45-O-13

Yield | Weight Indicator.................................45-O-14

Yield | Recording Status ...............................45-O-15

Page

Yield | Reset .................................................45-O-15

Yield | Edit/Select Calibration .......................45-O-16

Yield | Advanced Edit....................................45-O-18

Yield | Delete Unused Samples....................45-O-19

ActiveYield™ ................................................45-O-19

ActiveYield™ | Status Indicator ....................45-O-20

ActiveYield™ | Advanced Settings ...............45-O-21

ActiveYield™ | Reset....................................45-O-21

Chassis Tilt ...................................................45-O-22

Chassis Tilt Calibration Procedure ...............45-O-22

Threshing Clearance (Active Concave

Isolation)...................................................45-O-23

Threshing Clearance (Active Concave

Isolation) Calibration Procedure...............45-O-23

Unloading Auger Engage .............................45-O-24

Unloading Auger Engage Calibration

Procedure.................................................45-O-24

Deck Plate Spacing ......................................45-O-25

Deck Plate Spacing Calibration Procedure ..45-O-25

Feeder House Raise Speed .........................45-O-26

Feeder House Raise Speed Calibration

Procedure.................................................45-O-26

Header Calibration........................................45-O-27

Header Calibration Procedure......................45-O-27

Feeder House Tilt Fore/Aft Range................45-O-28

Feeder House Fore/Aft Tilt Range

Calibration Procedure ..............................45-O-28

Feeder House Lateral Tilt Range .................45-O-29

Feeder House Lateral Tilt Range

Calibration Procedure ..............................45-O-29

Feeder House Lateral Tilt Speed..................45-O-30

Feeder House Lateral Tilt Speed

Calibration Procedure ..............................45-O-30

Wings (Folding Corn Head)..........................45-O-31

Wings (Folding Corn Head) Calibration

Procedure.................................................45-O-31

Reel and Cutterbar Position .........................45-O-32

Reel and Cutterbar Position Calibration

Procedure.................................................45-O-32

Reel Position ................................................45-O-33

Reel Position Calibration Procedure.............45-O-33

Amber Flasher..............................................45-O-34

Amber Flasher Calibration Procedure ..........45-O-34

Concave Air Removal...................................45-O-35

Concave Air Removal Calibration

Procedure.................................................45-O-35

Concave Leveling.........................................45-O-36

Concave Leveling Calibration Procedure .....45-O-36

Combine Overview

Combine Overview ......................................... 45-P-1

Front Console................................................. 45-P-4

Corner Post Display........................................ 45-P-4

CommandARM™ Console and Display ....... 45-P-10

Multi-function Lever ...................................... 45-P-11

Navigation Bar.............................................. 45-P-12

Right-Hand Cab Items.................................. 45-P-15

Continued on next page

v070717

PN=5

Find manuals at https://best-manuals.com

Contents

Page

Left-Hand Cab Items .................................... 45-P-18

Overhead Controls ....................................... 45-P-19

Seat Controls................................................ 45-P-20

Key Switch.................................................... 45-P-20

Adjusting Steering Wheel ............................. 45-P-21

Operate Lights.............................................. 45-P-22

Operate Turn Signals, Horn and High

and Low Beam ......................................... 45-P-22

Operate Windshield Wiper and Washer ....... 45-P-24

Operate Ether Injection (If Equipped)........... 45-P-25

ComfortCommand™ Operators Seat

(Basic Seat).............................................. 45-P-25

ComfortCommand™ Operators Seat

(Premium Seat) ........................................ 45-P-26

Seat Belts ..................................................... 45-P-29

Instructional Seat.......................................... 45-P-29

Harvesting Controls...................................... 45-P-30

HVAC............................................................ 45-P-33

Radio ............................................................ 45-P-33

Engine and Ground Drive............................. 45-P-34

Lights............................................................ 45-P-36

Console and Display..................................... 45-P-37

Feeder House Reverser ............................... 45-P-38

Belt Pickup Cleanout .................................... 45-P-38

Header Engage ............................................ 45-P-39

Separator Engage ........................................ 45-P-39

Threshing Clearance Adjust ......................... 45-P-39

Threshing Speed Adjust ............................... 45-P-40

Cleaning Fan Speed Adjust.......................... 45-P-40

Chaffer Adjust............................................... 45-P-41

Sieve Adjust.................................................. 45-P-41

Seek ............................................................. 45-P-42

Push Button Shift Gear (If Equipped) ........... 45-P-42

ProDrive™ (If Equipped) .............................. 45-P-42

Road Transport Disconnect.......................... 45-P-43

Four-Wheel Drive (If Equipped).................... 45-P-43

Differential Lock (If Equipped) ...................... 45-P-44

Park Brake.................................................... 45-P-44

Exhaust Filter Cleaning Indicator.................. 45-P-44

Fuel Level Indicator ...................................... 45-P-44

Diesel Exhaust Fluid (DEF) Level Indicator.. 45-P-45

Quick Stop Switch ........................................ 45-P-45

Unloading Auger Swing Switch .................... 45-P-46

Unloading Auger Drive Switch...................... 45-P-46

AutoTrac™ Resume Button (If Equipped) .... 45-P-46

Header Raise Lower and Tilt (If

Equipped) Switch ..................................... 45-P-47

Reel Raise and Lower and Reel Fore

and Aft (If Equipped) ................................ 45-P-47

Feeder House Backshaft Speed and

Adjustable Corn Head Deck Plates

(If Equipped)............................................. 45-P-47

Header Activation Buttons............................ 45-P-48

Active Terrain Adjustment™

Access Active Terrain Adjustment™...............45-Q-1

Active Terrain Adjustment™ Main Page .........45-Q-1

Page

Active Terrain Adjustment™ (ATA) Status ......45-Q-3

Automatic Adjustment.....................................45-Q-6

Advanced Settings..........................................45-Q-6

Advanced Settings | Uphill Sensitivity ............45-Q-7

Advanced Settings | Downhill Sensitivity........45-Q-9

Advanced Settings | Adjustment Triggers.....45-Q-10

Advanced Settings | Adjustment

Triggers | Auto Adjustment Step Size ...... 45-Q-11

Advanced Settings | Adjustment

Triggers | Auto Adjustment On/Off ...........45-Q-13

Radio

Select Radio Source with Generation 4

CommandCenter™ .................................... 45-R-1

AM, FM, Weather Channel Home Page......... 45-R-2

Premium Radio CD Home Page..................... 45-R-2

Premium Radio XM Home Page .................... 45-R-3

Premium Radio USB Home Page .................. 45-R-3

Premium Radio Bluetooth® Home

Page (If Equipped) ..................................... 45-R-4

Auxiliary Home Page......................................45-R-4

Lights and Signals

Lighting Locations...............................................50-1

Lighting Delay/Timeout.......................................50-7

Feeder House

Hydraulic Cylinder Safety Stop...........................55-1

Feeder House Side Shields................................55-2

Feeder House Doors ..........................................55-2

Feed Accelerator Top Access Door ....................55-3

Feeder House Bottom Door and Feed

Plate Seal Support (Style A) ..........................55-3

Feeder House Bottom Door and Feed

Plate Seal Support (Style B) ..........................55-4

Stone Trap..........................................................55-5

Adjust and Set Feeder House Fore/Aft

Tilt Frame (Manual Tilt) ..................................55-6

Set Feeder House Fore/Aft Tilt Frame

Zero Point (Hydraulic Tilt) (If Equipped).........55-8

Feeder House Conveyor Chain—Adjusting........55-9

Feeder House Conveyor Chain

Links—Removing ...........................................55-9

Feeder House Drum (Manual

Tilt)—Height Adjustment ..............................55-10

Feeder House Drum (Hydraulic Tilt) (If

Equipped)—Height Adjustment....................55-10

Feeder House Conveyor Speed—Changing.... 55-11

Feeder House Conveyor Drive

Chain—Adjusting .........................................55-12

Feeder House Top Shaft Sprockets..................55-13

Feeder House Variable Speed Drive

Belt—Replacing ...........................................55-13

Feeder House Variable Speed Drive

Belt—Adjusting.............................................55-15

Continued on next page

vi 070717

PN=6

Find manuals at https://best-manuals.com

Contents

Page

Header Reel/Belt Pickup Pump

Belt (Variable Speed Feeder

House)—Replacing ......................................55-19

Header Reel/Belt Pickup Pump

Belt (Variable Speed Feeder

House)—Adjusting .......................................55-24

Feeder House Fixed Speed Drive

Belt—Replacing ...........................................55-24

Feeder House Fixed Speed Drive

Belt—Adjusting.............................................55-25

Header Reel/Belt Pickup Pump Belt

(Fixed Speed Feeder House)—Replacing ...55-25

Header Reel/Belt Pickup Pump Belt

(Fixed Speed Feeder House)—Adjusting ....55-28

CommandTouch Multi-Speed Feeder

House Drive Belt—Replacing.......................55-28

CommandTouch Multi-Speed Feeder

House Drive Belt—Adjusting........................55-29

Header Reel/Belt Pickup Pump Belt

(CommandTouch Multi-Speed

Feeder House)—Replacing..........................55-29

Header Reel/Belt Pickup Pump Belt

(CommandTouch Multi-Speed

Feeder House)—Adjusting...........................55-31

Manual Tilt Indicator (Lateral Tilt System) ........55-31

Attach Multi-Coupler and Single Point

Latching........................................................55-32

Attaching and Detaching Header from

Feeder House ..............................................55-35

Single Point Latching—Adjusting .....................55-36

Level Land Feeder House Lower Cable

End—Adjusting ............................................55-38

Level Land Feeder House—Shim Adjusting.....55-38

Feeder House Latching Pins (Cleanout) ..........55-39

Feeder House Manual Unlatching....................55-39

Shear Screw Location ......................................55-39

Shields

Gull Wing Doors .................................................60-1

Gull Wing Door Cylinder Adjustment..................60-2

Left-Hand Side Shields.......................................60-2

Right-Hand Side Shields ....................................60-4

Separator Covers ...............................................60-5

Separator

Standard Feed Accelerator Wear

Strips—Replacing ..........................................65-1

Tough Crop Feed Accelerator Wear

Strips—Replacing ..........................................65-2

Tine Feed Accelerator Wear Strips—Replacing ..65-3

Tine Feed Accelerator Comb Floor

(Rice Machines) .............................................65-4

Tine Feed Accelerator Comb Floor

(Rice Machines)—Removing .........................65-4

Feed Accelerator Belt—Replacing .....................65-7

Feed Accelerator Belt—Adjusting.......................65-9

Page

Standard Speed High Capacity Feed

Accelerator—Changing Speed.......................65-9

High Speed High Capacity Feed

Accelerator—Changing To Slow Speed .......65-10

Concave Recommendations ............................65-10

Concave Types................................................. 65-11

Separator Grate Spacers.................................. 65-11

Separator Grate Types .....................................65-12

Separator Grate Covers (If Equipped)..............65-12

Separator Grate Interrupters (If Equipped).......65-13

Separator Grate Interrupter Locations

(If Equipped).................................................65-13

Concave Sector Gear Shear Bolts

(Standard Concave Adjust) ..........................65-14

Concave Sections (Standard Concave

Adjust)—Remove and Install........................65-14

Concave Sections (Active Concave

Isolation)—Remove and Install ....................65-19

Concave Leveling (Standard Concave

Adjust) ..........................................................65-28

Concave Leveling (Active Concave Isolation) ..65-31

Separator Top Cover Vanes (If Equipped)........65-38

Threshing Elements and Tines

(TriStream Rotor)—Remove and Install.......65-38

Threshing Element and Separator

Tine Location (TriStream™ Rotor

Standard Configuration) ...............................65-40

Threshing Element and Separator Tine

Location (TriStream Rotor Tough

Grain Configuration).....................................65-41

Threshing Element and Separator Tine

Location (TriStream Rotor Dense

Pack Configuration)......................................65-42

Threshing Elements and Tines

(Variable Stream Rotor)—Remove

and Install.....................................................65-43

Threshing Element and Separator Tine

Location (Variable Stream Rotor

Standard Configuration) ...............................65-46

Threshing Element and Separator Tine

Location (Variable Stream Rotor

Dense Pack Configuration) ..........................65-47

Posi-Torq™ Separator—Dual-Range ...............65-48

Separator Drive Sheave Gap—Adjusting.........65-49

Separator Variable Drive Belt—Replacing........65-50

Auger Bed Dividers...........................................65-50

Discharge Beater Belt—Adjusting ....................65-51

Discharge Beater Belt—Replacing...................65-51

Discharge Beater Wear

Strips—Replacing (5 and 10 Wing Style).....65-56

Standard Discharge Beater Wear

Strips—Replacing (8 Wing Style).................65-57

Tough Crop Discharge Beater Wear

Strip—Replacing ..........................................65-58

Overshot Beater Belt (If

Equipped)—Adjusting ..................................65-58

Continued on next page

vii 070717

PN=7

Contents

Page

Overshot Beater Belt (If

Equipped)—Replacing .................................65-59

Overshot Beater (If Equipped)—Wing

Replacing .....................................................65-60

Countershaft Right-Hand Front

Belt—Adjusting.............................................65-61

Countershaft Right-Hand Front

Belt—Replacing ...........................................65-61

Countershaft Right-Hand Rear

Belt—Adjusting.............................................65-62

Countershaft Right-Hand Rear

Belt—Replacing ...........................................65-62

Cleaning Shoe Air Chutes and Access Door....65-63

Cleaning Shoe Auger Gears—Manual

Cleanout Door (If Equipped) ........................65-63

Cleaning Shoe Auger

Gears—Cleanout Door (If Equipped) ...........65-63

Shoe, Fan, and Conveyor Auger

Belt—Adjusting.............................................65-64

Shoe, Fan, and Conveyor Auger

Belt—Replacing ...........................................65-64

Cleaning Fan Actuator (Without Active

Terrain Adjustment™)—Adjusting ................65-65

Cleaning Fan Actuator (Active Terrain

Adjustment™)—Adjusting ............................65-65

Cleaning Fan Belt (Without Active

Terrain Adjustment™)—Replacing...............65-66

Cleaning Fan Belt (Active Terrain

Adjustment™)—Replacing...........................65-66

Adjustable Front Chaffer (If Equipped).............65-67

Fixed Front Chaffer...........................................65-67

Chaffer and Sieve—Measuring ........................65-67

General-Purpose Chaffer 30 mm

(1-3/16 in).....................................................65-68

Deep-Tooth Chaffer 41 mm (1-5/8 in)...............65-69

General Purpose Sieve 30 mm (1-3/16 in).......65-69

Deep-Tooth Sieve 30 mm (1-3/16 in)................65-69

Chaffer/Sieve Adjusting Switch ........................65-70

Dual Zone Adjust Rear Chaffer—Adjusting......65-70

Chaffer/Sieve Elements—Remove and

Install............................................................65-70

Chaffer/Sieve/Return Pan Assemblies .............65-74

Chaffer/Sieve Motor—Manual Adjust ...............65-74

Clean Grain Elevator Belt—Adjusting...............65-75

Clean Grain Elevator Belt—Replacing .............65-76

Clean Grain Elevator Conveyor

Chain—Adjusting .........................................65-77

VisionTrak™ Operational Checks.....................65-78

ActiveVision™ Clean Grain Elevator

Camera (If Equipped)...................................65-78

ActiveVision™ Tailings System

Camera (If Equipped)...................................65-79

Tailings System Elevator Sensors ....................65-80

Tailings System Elevator Paddles ....................65-81

Tailings Elevator Drive Belt—Adjusting

(Style A) .......................................................65-81

Page

Tailings System Elevator Paddle

Chain—Adjusting .........................................65-82

Upper Tailings Auger Drive

Chain—Adjusting (Style A)...........................65-82

Tailings System Drive Belt—Adjusting

(Style B) .......................................................65-83

Tailings System Drive Belt—Replacing

(Style B) .......................................................65-84

Tailings System Drive Chain—Adjust-

ing (Style B)..................................................65-85

Tailings System Drive Chain—Replac-

ing (Style B)..................................................65-85

Tailings System Wear Strips and Rasp

Bars—Remove and Install (Style B).............65-86

Tailings System Wear Strips and Rasp

Bars—Adjusting (Style B).............................65-88

Tailings System Return

Concave—Adjusting (Style B)......................65-90

Tailings System Auger Cleanout Door

(Style B) .......................................................65-90

Drive Belts—Left-Hand.....................................65-91

Drive Belts—Right-Hand (Style A)....................65-92

Drive Belts—Right-Hand (Style B)....................65-93

Feed Accelerator—Unplugging ........................65-93

Separator—Unplugging....................................65-94

Discharge Beater—Unplugging........................65-94

Residue Management

Residue Material Handling Options....................70-1

General Windrowing Information

(Deluxe Residue) ...........................................70-2

Crop Diverter Vanes—Adjusting.........................70-3

General Windrowing Information

(Premium Residue) ........................................70-4

Windrow Convergence Rakes............................70-4

Tailboard—Adjusting (Deluxe Residue)..............70-5

Tailboard Vanes (Manual

Adjust)—Adjusting (Deluxe Residue).............70-5

Tailboard Vanes (Manual

Adjust)—Factory Settings (Deluxe Residue) ..70-6

PowerCast™ Tailboard—Adjusting (Optional)....70-7

PowerCast™ Tailboard Blade—Re-

placing (Optional) ...........................................70-7

PowerCast™ Tailboard (Optional) Rear

Shrouds..........................................................70-8

Crop Diverter ......................................................70-9

Air Chutes.........................................................70-10

Overshot Beater Floor (If

Equipped)—Removing (Premium

Residue).......................................................70-10

Chopper Controller Bar (Optional).................... 70-11

Chopper Stationary Knifebank—Adjusting .......70-12

Chopper Stationary Knife Blades—Replacing ..70-12

Chopper Access Door ......................................70-13

Fine Cut Chopper Blades—Replacing

and Configuration.........................................70-14

Continued on next page

viii 070717

PN=8

Contents

Page

Middle Splitter Knife—Replacing

(Advanced PowerCast™ Tailboard) .............70-16

Chopper Blades—Centering.............................70-16

Chopper Adjusting Switch ................................70-18

Chopper Drive Speeds—Changing ..................70-18

Advanced PowerCast Spreader

Disks—Replacing.........................................70-20

Spreader (General Information)........................70-22

Spreader—Windrow Position ...........................70-22

Spreader—Lowering.........................................70-24

Spreader Disks (Single Speed)—Replacing.....70-25

Spreader Disks (Dual Speed)—Replacing .......70-26

Wide Spread Straw Spreader (Optional)..........70-27

Chopper Drive Belt Tension—Adjusting ...........70-28

Chopper Belt—Replacing.................................70-29

Chopper Jackshaft Belt—Adjusting..................70-34

Chopper Jackshaft Belt—Replacing

(Style A) .......................................................70-34

Chopper Jackshaft Belt—Replacing

(Style B) .......................................................70-37

Grain Tank and Unloading System

Grain Tank/Engine Ladder..................................75-1

Grain Tank Drain Holes ......................................75-1

Grain Tank Sample Trough.................................75-2

Grain Tank Fill Sensors—Adjusting ....................75-3

Grain Tank Covers (If Equipped)—Operating.....75-3

Grain Tank Covers (If Equipped)—Adjusting......75-4

Grain Tank Cross Auger Covers.........................75-4

ActiveYield™ (If Equipped) Cross

Auger Covers—Removing .............................75-5

ActiveYield™ (If Equipped) Sensor Locations....75-6

Shear Bolt Location ............................................75-6

Unloading Auger Drive Shear Bolt......................75-7

Grain Tank Loading Auger Deflector ..................75-7

Grain Tank Loading Auger (Grain Tank

Extensions)—Folding .....................................75-7

Grain Tank Loading Auger (Grain Tank

Covers)—Adjusting ........................................75-8

Mass Flow Sensor Plate (Grain Tank

Extensions)—Cleaning...................................75-9

Mass Flow Sensor Plate (Grain Tank

Covers)—Cleaning.......................................75-10

Unloading Auger Drive Chain—Adjusting.........75-10

Unloading Auger Cradle Support—Adjusting ... 75-11

Unloading Auger Position—Adjusting............... 75-11

Unloading Auger Lock Arm Positions...............75-12

Unloading Auger Drive Belt—Replac-

ing (Style A)..................................................75-12

Unloading Auger Drive Belt—Replac-

ing (Style B)..................................................75-14

Service - Electrical System

Welding Near Electronic Control Units ...............80-1

Keep Electronic Control Unit

Connectors Clean ..........................................80-1

Observe Electrical Precautions ..........................80-1

Page

Basic Electrical Component Handling

/ Precautions for Vehicles Equipped

with Computer Controlled Systems................80-2

Handling Batteries Safely ...................................80-3

Batteries—Safe Installation ................................80-4

Battery Cables—Connecting ..............................80-4

Batteries—Charging ...........................................80-5

Batteries—Checking Specific Gravity.................80-5

Batteries—Connecting Booster ..........................80-6

Batteries—Removing and Installing

(Style A) .........................................................80-6

Batteries—Removing and Installing

(Style B) .........................................................80-7

Battery Disconnect Switch..................................80-8

Machine Fuse Center .........................................80-9

Inline Fuses ......................................................80-10

Cab Fuse Center ..............................................80-10

Video Safety ..................................................... 80-11

Video Interface Capability................................. 80-11

Adjust Cameras (If Equipped) ..........................80-12

Safety Rules When Replacing Halogen Bulbs ..80-12

Cab Headlight Bulb—Replacing.......................80-13

Cab Headlights—Adjusting...............................80-13

Cab Halogen Light Bulb—Replacing................80-14

Cab Halogen Lights—Adjusting........................80-14

Fascia Light Bulb (If Equipped)—Replacing.....80-15

Lower Driving Light Bulb (If

Equipped)—Replacing .................................80-15

Lower Driving Light Bulb (If

Equipped)—Adjusting ..................................80-16

Light Emitting Diode (LED) Lights

(Optional)—Replacing..................................80-16

Light Emitting Diode (LED) Lights

(Optional)—Adjusting ...................................80-18

Beacon Lights—Replacing ...............................80-19

Warning Lights—Replacing ..............................80-19

Discharge Lights, Auxiliary Field Lights,

Access Door Work Lights, Stubble

Lights, Grain Tank and Unloading

Auger Light—Replacing ...............................80-20

Side Finder Lights and Cleaning Shoe

Lights—Replacing ........................................80-20

Warning Lights—Replacing ..............................80-20

Rear Hazard Lights and Marker/Brake

Lights—Replacing ........................................80-21

Cab Interior Light—Replacing ..........................80-21

Map Light—Replacing ......................................80-21

Ground Drive and Rear Axle

Service Tires Safely............................................85-1

Tire Loading Decal .............................................85-1

Care and Service of Tires...................................85-2

Front Tire Pressure (Single Tire

Configuration) (Corn Heads) ..........................85-3

Front Tire Pressure (Dual Tire

Configuration) (Corn Heads) ..........................85-5

Continued on next page

ix 070717

PN=9

Contents

Page

Front Tire Pressure (Single Tire

Configuration) (Belt Pickup / Rigid

and Flex Platforms / Rigid Draper

and Flex Draper) ............................................85-7

Front Tire Pressure (Dual Tire

Configuration) (Belt Pickup / Rigid

and Flex Platforms / Rigid Draper

and Flex Draper) ............................................85-9

Rear Tire Pressure (Two-Wheel Drive

Axle) (Corn Heads) ...................................... 85-11

Rear Tire Pressure (Four-Wheel Drive

Axle) (Corn Heads) ......................................85-13

Rear Tire Pressure (Two-Wheel Drive

Axle) (Belt Pickup / Rigid and Flex

Platforms / Rigid Draper and Flex Draper)...85-15

Rear Tire Pressure (Four-Wheel Drive

Axle) (Belt Pickup / Rigid and Flex

Platforms / Rigid Draper and Flex Draper)...85-17

Front and Rear Tire Information .......................85-18

Drive Wheel Starter Stud..................................85-19

Drive Wheel Bolt Torque (Single Wheel

Configuration)...............................................85-19

Drive Wheel Bolt Torque (Dual Wheel

Configuration)...............................................85-20

Front Drive Wheel Offset..................................85-21

Preparing Dual Wheels for Transport

or Service .....................................................85-21

Remove Front Wheels—Dual Wheels..............85-22

Install Front Wheels—Dual Wheels..................85-24

Single Attach Wide Spaced Dual

Wheels (Optional) ........................................85-25

Rear Wheel Bolt Torque ...................................85-26

Using Liquid Weight..........................................85-26

Ballast Requirements (S760)............................85-27

Ballast Requirements (S770)............................85-28

Ballast Requirements (S780 and S790) ...........85-29

Jack Pocket Locations Decal............................85-30

Transporting

Driving Machine on Roads .................................90-1

Back-Up Alarm ...................................................90-5

Transporting Machine on a Trailer......................90-5

Machine Tie Down Locations Decal .................90-12

Towing Machine (Mechanical Shift

Transmission Machines) ..............................90-13

Front Tow Hook ................................................90-13

Rear Tow Hook .................................................90-14

Harvesting Hints

Operation at Low Temperatures .........................95-1

Harvesting Tips...................................................95-1

Activation Button Mode Combinations................95-2

Change Tire Radius Code ..................................95-2

Single Point Yield Calibration Or

Multi-Point Yield Calibration ...........................95-3

Page

Crop Settings

Alfalfa / Barley ..................................................100-1

Canola / Chickpeas ..........................................100-2

Corn (Dry) / Corn (Wet) ....................................100-3

Corn Cob Mix / Edible Beans ...........................100-4

Flax / Grass Seed.............................................100-5

Guar (Cluster Beans) / Lentils ..........................100-6

Lupins / Millet....................................................100-7

Mustard / Navy Beans ......................................100-8

Oats / Peas.......................................................100-9

Popcorn / Rape Seed (Dry) ............................100-10

Rape Seed (Green) / Rice.............................. 100-11

Rye / Safflower ...............................................100-12

Sorghum / Soybeans......................................100-13

Sunflower / Triticale ........................................100-14

Wheat Difficult / Wheat Normal ......................100-15

Footnotes Description Page ...........................100-16

Concave Recommendations ..........................100-16

Power Shutdown Procedure...........................100-17

Payable Moisture and Density Chart..............100-18

Standard Weights Chart .................................100-18

Fire Prevention

Recommended Fire Preventions......................105-1

Fire Extinguisher Operation..............................105-1

Charge Liquid Fire Extinguisher (If Required) ..105-2

Handle Fuel Safely—Avoid Fires......................105-2

Prepare for Emergencies..................................105-2

Handle Starting Fluid Safely.............................105-3

Remove Accumulated Crop Debris ..................105-3

Fire Extinguishers.............................................105-3

Fire Extinguisher Locations ..............................105-4

In Case of Fire..................................................105-4

Cleaning Engine Compartment ........................105-5

Machine Cleanout

General Cleaning Guidelines............................ 110-1

Cleaning Out Machine (Periodic Cleanout) ...... 110-2

Cleaning Out Machine (Annual

Cleanout and Specialty Crops) .................... 110-9

Fuels and Lubricants

Handle Fuel Safely—Avoid Fires...................... 115-1

Avoid Static Electricity Risk When Refueling.... 115-1

Fuel Tank—Filling ............................................. 115-2

Handling and Storing Diesel Fuel..................... 115-2

Diesel Fuel........................................................ 115-3

BioDiesel Fuel .................................................. 115-4

Lubricity of Diesel Fuel ..................................... 115-5

Supplemental Diesel Fuel Additives................. 115-5

Testing Diesel Fuel ........................................... 115-5

Minimizing the Effect of Cold Weather

on Diesel Engines ........................................ 115-6

Continued on next page

x070717

PN=10

Contents

Page

Diesel Exhaust Fluid (DEF) — Use in

Selective Catalytic Reduction (SCR)

Equipped Engines ........................................ 115-7

Testing Diesel Exhaust Fluid (DEF).................. 115-7

Storing Diesel Exhaust Fluid (DEF).................. 115-8

Refilling Diesel Exhaust Fluid (DEF) Tank........ 115-9

Cleaning Diesel Exhaust Fluid (DEF) Tank .... 115-10

Disposal of Diesel Exhaust Fluid (DEF) ......... 115-10

Diesel Engine Coolant (engine with

wet sleeve cylinder liners) .......................... 115-11

John Deere COOL-GARD™ II Coolant

Extender..................................................... 115-12

Operating in Warm Temperature Climates ..... 115-12

Water Quality for Mixing with Coolant

Concentrate................................................ 115-13

Testing Coolant Freeze Point ......................... 115-14

Diesel Engine Break-In Oil —

Non-Emissions Certified and

Certified Tier 1, Tier 2, Tier 3, Stage

I, Stage II, and Stage III ............................. 115-15

John Deere Break-In Plus™ Engine Oil

— Interim Tier 4, Final Tier 4, Stage

IIIB, and Stage IV ....................................... 115-15

Diesel Engine Oil — Tier 2 and Stage II......... 115-16

Diesel Engine Oil — Tier 3 and Stage III........ 115-17

Diesel Engine Oil — Interim Tier 4,

Final Tier 4, Stage IIIB, and Stage IV......... 115-18

Diesel Engine Oil Service Interval for

Operation at High Altitude .......................... 115-18

Engine Oil and Filter Service Intervals

— Tier 2 and Stage II Engines ................... 115-19

Engine Oil and Filter Service Intervals

— Tier 3 and Stage IIIA —

PowerTech™ Plus Engines........................ 115-20

Engine Oil and Filter Service Intervals

— Interim Tier 4, Final Tier 4, Stage

IIIB, and Stage IV Engines ......................... 115-21

Oilscan™ and CoolScan™............................. 115-21

ProDrive™ Transmission,

CommandTouch™ Multi-Speed

Feeder House Drive, Hydrostatic

Drive System, Main Hydraulic

System, and Main Engine Gear

Case Oils.................................................... 115-22

Transmission (Mechanical Shift

and Push-Button Shift), Final

Drives, Loading Auger, Primary

Countershaft, and Two-Speed

Separator Drive Gear Case Oils ................115-23

Feeder House Reverser Gear Case............... 115-24

Grease............................................................ 115-24

Brake Fluid (If Equipped)................................ 115-24

Oil Filters ........................................................ 115-25

Fuel Filters...................................................... 115-25

Alternative and Synthetic Lubricants .............. 115-25

Lubricant Storage ........................................... 115-25

Mixing of Lubricants........................................ 115-25

Page

Lubrication and Maintenance

Service Interval—Setup or Clearing .................120-1

Lubrication Decal Locations .............................120-1

Hydraulic Hose Replacement...........................120-1

Hydraulic System Cleanliness..........................120-2

Accumulator Pressure ......................................120-2

Lubrication Symbols .........................................120-2

Service Your Machine at Specified Intervals ....120-2

Important Considerations .................................120-2

Maintenance—Every 10 Hours

Service Interval Chart—Every 10 Hours....... 120-A-1

Engine Oil Level ........................................... 120-A-2

Engine Coolant............................................. 120-A-3

Rotary Screen, Oil Cooler, Condenser,

Radiator, and Charge Air Cooler .............. 120-A-3

Hydrostatic/Hydraulic Oil .............................. 120-A-5

Main Engine Gearcase Oil............................ 120-A-6

Air Compressor Reservoir (If Equipped)....... 120-A-6

Fuel Precleaner Filter ................................... 120-A-6

Two Speed Four-Wheel Drive Motor

Pivots (Muddy Conditions) ....................... 120-A-7

Two-Wheel Drive Heavy-Duty and

Extra Heavy-Duty Axle Spindle

Bearings/Pivot Pins (Muddy Conditions).. 120-A-7

Final Drive Outer Bearings (Muddy

Conditions) ............................................... 120-A-7

Air Conditioner Drain Hose........................... 120-A-8

Variable Speed Feeder House

Reverser Drive Gear Case (S760

and S770 Machines) (Severe

Conditions) ............................................... 120-A-8

Stone Trap.................................................... 120-A-8

Tailings Elevator Slip Clutch (S780 and

S790 Machines) ....................................... 120-A-9

ActiveVision™ Tailings System

Camera (If Equipped)............................... 120-A-9

Maintenance—Every 50 Hours

Service Interval Chart—Every 50 Hours....... 120-B-1

Two Speed Four-Wheel Drive Motor

Pivots (Normal Conditions) ...................... 120-B-2

Two-Wheel Drive Heavy-Duty and

Extra Heavy-Duty Axle Spindle

Bearings and Pivot Pins (Normal

Conditions) ............................................... 120-B-2

Final Drive Outer Bearings (Normal

Conditions) ............................................... 120-B-2

Variable Speed Feeder House

Reverser Drive Gear Case (S760

and S770 Machines) (Normal

Conditions) ............................................... 120-B-3

Feeder House Reverser Drive Gear

Case Oil ................................................... 120-B-3

Variable Speed Feeder House Upper

Sheaves (S760 and S770 Machines)....... 120-B-3

Continued on next page

xi 070717

PN=11

Contents

Page

Lateral Tilt Feeder House ............................. 120-B-4

Separator Variable Speed

Driven/Driver Sheaves ............................. 120-B-4

Separator Variable Speed

Driven/Driver Sheaves (S780 and

S790 Machines) ....................................... 120-B-5

Cleaning Fan Variable Upper and

Lower Sheaves ........................................ 120-B-5

Fuel Precleaner Filter ................................... 120-B-5

Two-Speed Separator Drive Oil.................... 120-B-6

Water Separator Primary Fuel Filter............. 120-B-6

Radiator, Charge Air Cooler, Oil Cooler,

and Condenser......................................... 120-B-7

Mass Flow Sensor........................................ 120-B-7

Cab Fresh Air Filter ...................................... 120-B-7

ActiveVision™ Clean Grain Elevator

Camera (If Equipped)............................... 120-B-8

Maintenance—First 100 Hours

Service Interval Chart—First 100 Hours....... 120-C-1

Main Engine Gear Case Filter (S760

and S770 ProDrive™ Machines)..............120-C-1

Main Engine Gear Case Lube Filter

(ProDrive™ Machines)............................. 120-C-1

Maintenance—Every 100 Hours

Service Interval Chart—Every 100 Hours..... 120-D-1

Tire Pressure and Bolt Torque......................120-D-1

Maintenance—Every 200 Hours

Service Interval Chart—Every 200 Hours..... 120-E-1

Recirculating Filter........................................ 120-E-1

Primary Countershaft (Multi-Speed

Feeder House on S770, S780, and

S790 Machines) ....................................... 120-E-2

Separator Variable Speed

Driven/Driver Sheaves (S760 and

S770 Machines) ....................................... 120-E-2

Maintenance—Every 250 Hours

Service Interval Chart—Every 250 Hours..... 120-F-1

Engine Oil and Filter (Tier 2/Stage II

and Tier 3/Stage IIIA) ............................... 120-F-2

Engine Oil and Filter (Final Tier 4/Stage IV).. 120-F-3

Fuel Tank Breather ....................................... 120-F-3

Diesel Exhaust Fluid (DEF) Tank

Breather (Final Tier 4/Stage IV) ............... 120-F-4

Maintenance—Every 400 Hours

Service Interval Chart—Every 400 Hours.....120-G-1

Fuel Precleaner Filter ...................................120-G-1

Water Separator ...........................................120-G-2

Primary and Secondary Fuel Filter...............120-G-3

Variable Speed Driver/Driven Sheaves

(Final Tier 4/Stage IV) (S760 and

S770 Machines) .......................................120-G-4

Page

Unloading Auger Upper Gear Case..............120-G-4

Header/Reel Drive Pump Sheave Bearing...120-G-5

Primary Countershaft Universal Joint

Spline (Non-Multi-Speed Feeder

House)......................................................120-G-5

Vertical Unloading Auger Upper Gear

Case (S780 and S790 Machines) ............120-G-5

Chopper/Unloading Driveshaft Bearing........120-G-6

Variable Speed Driver Sheave .....................120-G-6

Feed Accelerator Bearings...........................120-G-6

Service Interval Chart—Every 400

Hours (Continued)....................................120-G-7

Tailings Auger Drive Slip Clutch (S760

and S770 Machines) ................................120-G-7

Conveyor Auger Drive Slip Clutch................120-G-8

Right-Hand Side Lube Bank.........................120-G-8

Overshot Beater Bearings (Optional)

(S770, S780, and S790 Machines) ..........120-G-8

Discharge Beater Bearings...........................120-G-9

Cleaning Fan Shaft Bearings........................120-G-9

Rear Axle Tie Rod ........................................120-G-9

Spreader Disk (If Equipped) .......................120-G-10

Overshot Beater Gear Case Oil

(Optional) (S770, S780, and S790

Machines)...............................................120-G-10

Separator Drive Oil.....................................120-G-10

Final Drive Oil............................................. 120-G-11

Service Interval Chart—Every 400

Hours (Continued)..................................120-G-12

Transmission Oil (S760 and S770

Non-ProDrive™ Machines) ....................120-G-13

Park Brake Cylinder Cables (S760

and S770 Push-Button Shift

Transmission Machines) ........................120-G-13

Final Drive Couplers...................................120-G-13

Batteries .....................................................120-G-14

Hydraulic/Hydrostatic Filter (S760 and

S770 Machines) .....................................120-G-14

Hydrostatic Charge Filter............................120-G-15

Main Engine Gear Case Filter ....................120-G-15

Engine Debris Management Air Filter

(Final Tier 4/Stage IV Engines) ..............120-G-16

Fire Extinguishers.......................................120-G-16

Primary Countershaft Gear Case Oil

(Fixed Speed and Variable Speed

Feeder House Drive)..............................120-G-16

Brake Fluid (S760 and S770

Non-ProDrive™ Machines) ....................120-G-17

Seat Belts ...................................................120-G-17

ProDrive™/Main Engine Gear Case

Lube Filter (ProDrive™ Machines).........120-G-17

Feeder House Slip Clutch...........................120-G-18

Multi-Speed Feeder House Drive

(S770, S780, and S790 Machines) ........120-G-18

Loading Auger Gear Case Oil ....................120-G-18

Continued on next page

xii 070717

PN=12

Contents

Page

Diesel Exhaust Fluid (DEF) Tank

Breather (Final Tier 4/Stage IV

Engines) .................................................120-G-19

Fuel Tank Breather .....................................120-G-19

Air Filter Elements ......................................120-G-19

Moisture Sensor (If Equipped)....................120-G-20

Maintenance—Every 800 Hours

Service Interval Chart—Every 800 Hours..... 120-H-1

Feeder House Reverser Gear Case............. 120-H-1

Maintenance—Every 1000 Hours

Service Interval Chart—Every 1000

Hours (ProDrive™ Machines) ....................120-I-1

Change Main Engine Gear Case Oil ..............120-I-2

Hydraulic Reservoir Filter (S780 and S790)...120-I-3

Maintenance—Every 2000 Hours

Service Interval Chart—Every 2000 Hours....120-J-1

Hydraulic/Hydrostatic Reservoir Oil...............120-J-2

Engine Valve Backlash ..................................120-J-2

Final Drives Oil ..............................................120-J-3

Main Engine Gear Case Oil

(Non-ProDrive™ Machines) ......................120-J-3

Separator Drive Oil........................................120-J-3

Primary Countershaft Gear Case Oil

(Fixed Speed and Variable Speed

Feeder House) ..........................................120-J-4

Transmission Oil (Mechanical Shift and

Push-Button Shift Transmission)...............120-J-4

Overshot Beater Gear Case Oil

(Optional) (S770, S780, and S790

Machines)..................................................120-J-4

Maintenance—Every 4500 Hours or Three Years

Service Interval Chart—Every 4500

Hours or Three Years............................... 120-K-1

Diesel Exhaust Fluid (DEF) Dosing

Filter (Final Tier 4/Stage IV Engines) ....... 120-K-1

Maintenance—Every 4500 Hours or Five Years

Service Interval Chart—Every 4500

Hours or Five Years...................................120-L-1

4500 Hours or Five Years..............................120-L-1

Maintenance—Every 6000 Hours or Six Years

Service Interval Chart—Every 6000

Hours or Six Years ...................................120-M-1

Engine Cooling System ................................120-M-2

Maintenance—As Required

Service Interval Chart—As Required............ 120-N-1

Recirculating Filter........................................ 120-N-1

Cab Fresh Air Filter ...................................... 120-N-2

Windshield Washer Reservoir ...................... 120-N-2

Page

Alternator Screen.......................................... 120-N-2

Moisture Sensor (If Equipped)...................... 120-N-3

ActiveVision™ Clean Grain Elevator

Camera (If Equipped)............................... 120-N-3

ActiveVision™ Tailings System

Camera (If Equipped)............................... 120-N-3

Maintenance—As Required (Engine Fluids and

Filters)

Required Emission-Related Information.......120-O-1

Rear Ladder and Landing.............................120-O-1

Engine Filter Access Cover ..........................120-O-1

Engine Access Covers .................................120-O-1

Changing Starting Fluid Can ........................120-O-2

Do Not Modify Engine Power or

Fuel/Air System........................................120-O-2

Fuel System..................................................120-O-2

Diesel Exhaust Fluid (DEF)

Tank—Filling (Final Tier 4/Stage IV).........120-O-3

Diesel Exhaust Fluid (DEF)

Tank—Draining (Final Tier 4/Stage IV).....120-O-4

Diesel Exhaust Fluid (DEF) Dosing

Filter—Replacing (Final Tier 4/Stage IV) ..120-O-5

Fuel Tank—Filling .........................................120-O-6

Fuel Tank—Draining .....................................120-O-6

Fuel Tank—Shut-Off Valve ...........................120-O-6

Water Separator Primary Fuel

Filter—Draining ........................................120-O-7

Fuel Precleaner Filter—Cleaning .................120-O-7

Heavy-Duty Fuel Precleaner Filter

(Optional)—Flushing ................................120-O-8

Heavy-Duty Fuel Precleaner Filter

(Optional)—Replacing and Cleaning........120-O-9

Primary and Secondary Fuel Filter

Element—Replacing ..............................120-O-10

Fuel System—Bleeding.............................. 120-O-11

Cooling System—Draining .........................120-O-12

Cooling System—Filling .............................120-O-14

Cooling System—Winterize........................120-O-14

Air Cleaner Filters—Removing...................120-O-15

Air Compressor System (If Equipped)........120-O-16

Diesel Particulate Filter Maintenance

and Service (Final Tier 4/Stage IV) ........120-O-17

Exhaust Filter / Diesel Particulate Filter

Ash Handling and Disposal (Final

Tier 4/Stage IV) ......................................120-O-17

Exhaust Filter Disposal (Final Tier

4/Stage IV) .............................................120-O-17

Engine Debris Management Air

Filter—Removing (Final Tier

4/Stage IV) .............................................120-O-18

Maintenance—As Required (9.0 L Engine Belts)

Engine Belt—Routing (Tier 2/Stage II

and Tier 3/Stage IIIA) ............................... 120-P-1

Engine Accessory/Fan Drive/Air

Compressor (If Equipped)

Continued on next page

xiii 070717

PN=13

Contents

Page

Belt—Replacing (Tier 2/Stage

II and Tier 3/Stage IIIA) ............................ 120-P-1

Rotary Screen Belt—Routing ....................... 120-P-5

Rotary Screen Drive Belt—Replacing

(Tier 2/Stage II and Tier 3/Stage IIIA) ...... 120-P-5

Engine Belt—Routing (Final Tier

4/Stage IV) ............................................... 120-P-6

Air Conditioner Compressor/Alternator

Belt—Replacing (Final Tier 4/Stage IV) ... 120-P-7

Rotary Screen Drive Belt—Replacing

(Final Tier 4/Stage IV) ............................ 120-P-10

Vacuum Fan Drive Belt—Replacing

(Final Tier 4/Stage IV) ............................ 120-P-10

Vacuum Fan Driven Belt—Replacing

(Final Tier 4/Stage IV) ............................ 120-P-11

Variable Speed Fan Drive

Belt—Replacing (Final Tier 4/Stage IV).. 120-P-12

Air Compressor Belt (If

Equipped)—Replacing (Final Tier

4/Stage IV) ............................................. 120-P-17

Rotary Screen Brush—Adjustment............. 120-P-22

Engine Debris Management

Belt—Replacing (Final Tier 4/Stage IV).. 120-P-23

Maintenance—As Required (13.5 L Engine Belts)

Engine Belt—Routing (Tier 2/Stage II

and Tier 3/Stage IIIA) ...............................120-Q-1

Engine Accessory/Air Compressor (If

Equipped) Belt—Replacing (Tier

2/Stage II and Tier 3/Stage IIIA)...............120-Q-1

Fan Drive Belt—Replacing (Tier

2/Stage II and Tier 3/Stage IIIA)...............120-Q-7

Rotary Screen Belt—Routing .....................120-Q-10

Rotary Screen Drive Belt—Replacing

(Tier 2/Stage II and Tier 3/Stage IIIA) ....120-Q-10

Engine Belt—Routing (Final Tier

4/Stage IV) ............................................. 120-Q-11

Air Conditioner Compressor/Alternator

Belt—Replacing (Final Tier 4/Stage IV) ..120-Q-12

Rotary Screen Drive Belt—Replacing

(Final Tier 4/Stage IV) ............................120-Q-18

Vacuum Fan Drive Belt—Replacing

(Final Tier 4/Stage IV) ............................120-Q-19

Air Compressor Belt (If

Equipped)—Replacing (Final Tier

4/Stage IV) .............................................120-Q-19

Fan Drive Belt—Replacing (Final Tier

4/Stage IV) .............................................120-Q-22

Rotary Screen Brush—Adjustment.............120-Q-26

Engine Debris Management

Belt—Replacing (Final Tier 4/Stage IV) ..120-Q-26

Troubleshooting

Feeder House...................................................125-1

Separator..........................................................125-2

Hydrostatic Ground Drive .................................125-5

Four-Wheel Drive (Optional).............................125-7

Steering ............................................................125-7

Brakes ..............................................................125-8

Page

Engine ..............................................................125-9

Electrical.........................................................125-17

Heater.............................................................125-18

Air Conditioner................................................125-19

Moisture Sensor (If Equipped)........................125-19

Mass Flow Sensor (If Equipped) ....................125-20

Storage

Preparing Machine for Storage.........................130-1

Removing Machine From Storage....................130-2

Specifications

Operating Speeds (S760 and S770) ................135-1

Operating Speeds (S780 and S790) ................135-3

Specifications (S760 and S770) .......................135-5

Specifications (S780 and S790) .......................135-7

Dimensions (S760 and S770)...........................135-9

Dimensions (S780 and S790).........................135-10

Dimension Reference Points.......................... 135-11

Emissions Control System Certification

Label ..........................................................135-12

CARB Non-road Emissions Control

Warranty Statement—Compression

Ignition........................................................135-13

EPA Non-road Emissions Control

Warranty Statement—Compression

Ignition........................................................135-21

Limited Battery Warranty ................................135-23

Unified Inch Bolt and Screw Torque Values....135-24

Metric Bolt and Screw Torque Values.............135-25

Machine Identification Numbers

Interpreting Machine Serial Number.................140-1

Identification Numbers......................................140-1

Machine Identification Plate..............................140-2

Machine Identification Plate Location...............140-2

Interpreting Engine Serial Number ...................140-3

Engine Serial Number (Tier 2/Stage II

and Tier 3/Stage IIIA) ...................................140-4

Engine Serial Number (Final Tier

4/Stage IV) ...................................................140-4

Cab Serial Number...........................................140-4

Hydrostatic Drive Unit Pump ............................140-5

Hydrostatic Drive Unit Motor.............................140-5

Two Speed Four-Wheel Drive Motor ................140-5

Engine Gear Case............................................140-6

Rotor Drive Gear Case.....................................140-6

Transmission ....................................................140-6

Feeder House Reverser ...................................140-7

Multi-Speed Feeder House Gear Case

(If Equipped).................................................140-7

Chopper (If Equipped) ......................................140-7

Chopper Tailboard (Deluxe Residue) ...............140-8

Chopper Tailboard (Premium Residue) ............140-8

PowerCast Tailboard (Deluxe Residue)............140-8

Spreader (Deluxe Residue)..............................140-9

Keep Proof of Ownership .................................140-9

Keep Machines Secure ....................................140-9

xiv 070717

PN=14

Safety Features

SS43267,0000531 -19-09JUN15-1/1

Machine Safety Features

H114478 —UN—08JUN15

Front View/Rear View Safety Features

A—Cab Safety Features:

Operator's Presence System,

Electronic Engine Start

Lockout, Seat Belts, Horn,

Emergency Exit Window,

Park Brake, Turn Signals

B—Handholds

C—Headlights

D—Slip Resistant Skid Mats

E—Safety Signs

F— Mechanical Safety Stop

(Feeder House)

G—Slip Resistant Steps and

Platform with Handrails

H—Shields

I— Rear View Mirrors

J— Warning Lights and Reflective

Tape

K—Slow Moving Vehicle Emblem

L— Beacon Lights

M—Back-Up Alarm

N—Taillights

O—Slip Resistant Service

Platform with Handrails

P—Rotational Alarm Safety

Features: Discharge Light,

Stubble Lights, Gullwing

Service Lights

In addition to the safety features shown here, other

components and systems, safety lights on the machine,

and safety messages and instructions in the operator's

manual contribute to the safe operation of this machine

when combined with the care and concern of a capable

operator.

05-1 070717

PN=19

Safety

DX,ALERT -19-29SEP98-1/1

DX,SIGNAL -19-05OCT16-1/1

DX,READ -19-16JUN09-1/1

Recognize Safety Information

This is a safety-alert symbol. When you see this symbol

on your machine or in this manual, be alert to the potential

for personal injury.

Follow recommended precautions and safe operating

practices.

T81389 —UN—28JUN13

Understand Signal Words

DANGER; The signal word DANGER indicates a

hazardous situation which, if not avoided, will result in

death or serious injury.

WARNING; The signal word WARNING indicates a

hazardous situation which, if not avoided, could result in

death or serious injury.

CAUTION; The signal word CAUTION indicates a

hazardous situation which, if not avoided, could result in

minor or moderate injury. CAUTION may also be used

to alert against unsafe practices associated with events

which could lead to personal injury.

A signal word—DANGER, WARNING, or CAUTION—is

used with the safety-alert symbol. DANGER identifies

the most serious hazards. DANGER or WARNING

safety signs are located near specific hazards. General

TS187 —19—30SEP88

precautions are listed on CAUTION safety signs.

CAUTION also calls attention to safety messages in this

manual.

Follow Safety Instructions

Carefully read all safety messages in this manual and on

your machine safety signs. Keep safety signs in good

condition. Replace missing or damaged safety signs. Be

sure new equipment components and repair parts include

the current safety signs. Replacement safety signs are

available from your John Deere dealer.

There can be additional safety information contained on

parts and components sourced from suppliers that is not

reproduced in this operator's manual.

Learn how to operate the machine and how to use controls

properly. Do not let anyone operate without instruction.

Keep your machine in proper working condition.

Unauthorized modifications to the machine may impair the

function and/or safety and affect machine life.

TS201 —UN—15APR13

If you do not understand any part of this manual and need

assistance, contact your John Deere dealer.

10-1 070717

PN=20

This manual suits for next models

Table of contents

Popular Farm Equipment manuals by other brands

Sovema

Sovema FC-2 Series Operation & maintenance manual

Arrowquip

Arrowquip Q-POWER 107 Series product manual

Yetter

Yetter 2967-081 manual

horsch

horsch Focus 7 MT operating instructions

VOSS.farming

VOSS.farming BA-1261 instruction manual

pronovost

pronovost P-1624 Operator's manual

Reese

Reese 3400 Operator's manual

HME

HME 1250 Operator's manual

Monosem

Monosem Monobloc 260 manual

Krone

Krone TITAN 4/32 L Original operating instructions

AKO-Agrartechnik

AKO-Agrartechnik BA-1031 instruction manual

SaMASZ

SaMASZ FISHER Operator's manual

Worksaver

Worksaver SSGB-8B Owner's/operator's manual

Bush Hog

Bush Hog CPG Series Operator's manual

Caddon Hives

Caddon Hives WBC Assembly instructions

BLU-JET

BLU-JET LEGACY Assembly and operators manual

Morbark

Morbark TORNADO 13 Safety & Operators & Parts Manual

REIST INDUSTRIES

REIST INDUSTRIES Roto-Rake RR96 Operator and parts manual

john deer S760 User manual

Popular Farm Equipment manuals by other brands