John Lewis Milan Bed 803/45901 User manual

Milan Bed
PRE-ASSEMBLY PREPARATION
Please check the pack contents before attempting to assemble this product. A full checklist of components is
given in this leaflet. If any components are missing, please contact the John Lewis Helpline.
This product is HEAVY. It should be assembled as near as possible to the point of use. TAKE CARE WHEN
LIFTING to avoid personal injury and (or) damage to the product.
This product takes approximately 40 MINUTES to assemble with 2 PEOPLE.
The fittings pack contains SMALL ITEMS which should be KEPT AWAY FROM YOUNG CHILDREN.
Read this leaflet in full before commencing assembly.
If you require any additional information or have any issues with this product please call the
John Lewis Helpline on 01244 689949 or email [email protected]
Stock code choc: 803/45901
Stock code ivory: 803/46202
Single
John Lewis
For product support or spare parts please call
the John Lewis Helpline;
T: 01244 689949
E: [email protected]
Please ensure instructions are read in full before attempting to assemble this product.
Necessary Tools
Thank you for purchasing this Milan Bed. Please read the instructions carefully before use to ensure
safe and satisfactory operation of this product.
1/5
IMPORTANT! PLEASE KEEP THESE
INSTRUCTIONS FOR FUTURE
REFERENCE

2/5
Fittings and parts checklist
A
B
C
DM5 Allen Key x 1
M4 Allen Key x 1
Side Plastic Caps x 30
M6 x 40mm Bolt x 8
1
2
3
4
5
Headboard x 1
Footboard x 1
Side Rails x 2
Slats x 15
Legs x 4
Fittings
Parts

3/5
M5
BRACKET
SIDE RAIL
Step Two
Place metal fixing on Side Rails (3) over pre-inserted bolts in Headboard (1) and Footboard (2).
Tighten bolts with Allen Key M5 (D) to secure parts together.
Step by step assembly instructions
Step One
Place Wooden Legs (5) over the holes in the underside of the Headboard (1) and Footboard (2) as per
drawing. Insert 2 M6 x 40mm bolts (A) to fix each leg in place and tighten using Allen Key M4 (C) provided.
M5 x 1
M4 x1 M6 x 40mm x8
C
D
A
g. 1
M6 x 40 bolt
M6 x 40 bolt
M6 x 40 bolt
M6 x 40 bolt
Allen Key
Bed Leg
Preinserted Nut
Head/Foot
Board
5
5
5
5

4/5
Step Three
Step Four
Fix the Slats (4) to the bed by first inserting the Side Plastic Caps (B) on each end of the slats and then
pushing the caps into the holes in the Side Rails (3).
This bed is now ready to use.
B.
Side Plastic Cap x 30
Bent Slat x 15
4Side Rail
Side Plastic Cap
Slat

5/5
Care and Maintenance
Safety Instructions
This Milan bed should be cleaned using a soft, damp cloth and dried immediately.
Do not use a very wet cloth or allow any liquid contact for a long period of time as this can
permanently damage the surface.
Do not use detergents and do not rub as this can cause permanent damage.
Always protect your bed from direct sunlight as this may accelerate the natural ongoing
discolouration process.
Screws holding together the bed frame should be tightened regularly.
Please retain this information leaflet for future reference.
This product complies with BS EN 1725:1998.
If you require any additional information or have any issues with this product please call
the John Lewis Helpline on 01244 689949 or email [email protected]
John Lewis Partnership 171 Victoria Street, London, SW1E 5NN.
www.johnlewis.com
Never drag furniture when moving it. Always lift it.
Periodically check all fixings to ensure none have come loose and re-tighten where necessary.
Please take care when handling or moving the furniture as careless handling may cause
damage or injury. Furniture can be dangerous if incorrectly installed. Any assembly should be
carried out by a competent adult.No liability will be accepted for damage or injury caused by
incorrectly installed or assembled furniture. During assembly, children should be kept away from the
product due to possible risk of injury. Do not use this item if any components are missing or
damaged.
It is recommended that care is taken when moving heavy objects to a new location to avoid
personal injury or damage to the furniture. Please be careful to retain all fittings when doing this.
Children are likely to play, bounce, jump and climb on furniture, therefore the furniture should not be
placed too close to other furniture or windows, blind cords, curtain pulls or other strings or cords and
should be placed either tight to any wall or have a gap of 300mm between the wall and the side of
the bed.
This product complies with BS EN 8509:2008+A1:2011 and BS EN 1725:1998.
Warning: Not suitable for children under 4 years old.
Warning: Do not place this child’s bed near heat sources, windows or other furniture.
Warning: Do not use this child’s bed if any part is broken, torn or missing.
This bed is for use with a standard single size mattress L190 x W90 x H18.