John Lewis Rachel Dresser User manual

rachel dresser
Instruction manual
Important
retain for future reference
please read carefully

Important
Please read the instructions and warnings carefully before use to ensure safe and
satisfactory operation of this product.
Your child’s safety is your responsibility. If you have a query with this product or require
replacement parts, please contact your nearest John Lewis department store.
Lay out the parts on a soft level surface and compare to the part/fixing checklist on pages 2
and 3. Do not discard any packaging until you are sure that you have all the parts.
Keep children clear during assembly as pack contains small parts which may present a
choking hazard.
Recommended changing mat: 750 x 465 mm.
This product complies with BSEN 12221:2008 +A1:2013.
You will need the following tools to complete assembly:
Flat-headed screwdriver and Cross point screwdriver.
2
Hardware
A x 16
B x 2
C x 2
D x 33
E x 6 (15mm)
F x 18 (30mm)
H x 4 (55mm)
G x 20
Hexagon Key x 1
J x 6

3
Wooden Parts
Crossbar x 1
Top Panel x 1
Drawer Brace x 3
Drawer Back x 3
Side Panel x 2 (L & R)
Foot x 4
Drawer Side (L & R) x 6
Drawer Base x 3
Changer Front x 1
Changer Side x 2 (L & R)
Back Panel (Top) x 1
Back Panel (Bottom) x 1
Drawer Front x 3
Changer Back x 1
Base x 1

4
A x 2
A x 2
NOTE: Take care to insert the dowels
into the correct holes as indicated.
Repeat for the opposite end of each
Assembly 1
Assembly 2
Foot
x 4
Crossbar
Top Panel
Base
Base
Foot
H x 4

Assembly 3
Assembly 4
5
F x 3
F x 3
F x 6
Top Panel
Base
Side Panel
Side Panel
Crossbar

6
Back panel (top)
Back panel (bottom)
NOTE: Slot at top
G x 10
(each panel)
D x 4
(each side)
E x 2
Drawer side
Drawer back
Drawer side
Drawer front
J x 2
NOTE: Repeat for remaining drawers
NOTE:
When fitting the back, push the panel
into the corner so that the side and top
edges contact the rebate evenly all the
way around the frame of the dresser.
This will ensure that the dresser frame
is square and that the drawers will align
with each other.
Assembly 6
Assembly 5

Drawer Base
Drawer Brace
D x 3
NOTE: Repeat for remaining drawers
Assembly 8
Changer Back
Changer Front
Changer Side (x 2)
B (each end)
A x 2
(each end)
A x 2
7
Assembly 7

Assembly 10
NOTE: To allow easier fitting to the Dresser,
do not fully tighten bolts until the end of
"Assembly 10"
F x 2
F x 2
8
NOTE:
Insert Cam Nut (Part C) with arrowed
slot facing the Changer Front.
To lock Changer Front in place, turn
Cam nuts (part C) 1/2 turn clockwise
with a large flat-bladed screwdriver after
assembly.
Assembly 9
F x 2
C x 2
Changer Front
Changer Side
Changer Back
Changer Side

The dresser is supplied with a fixing kit which will secure it and help to guard against accidental tipping.
WARNING : Installation only to be carried out by a competent person.
Check the suitability of the wall before fitting.
1. Place dresser against the wall where it is to be fitted. Mark the wall 25mm (1”) down from the top surface
of the changer.
2. Using the 25mm screw, washer and the appropriate wall fixing attach the fabric strap to the marked
position.
3. Remove the top drawer and thread the free end of the strap through the slot in the back panel.
4. From the inside of the dresser, attach the fabric strap to the dresser frame using the 15mm screw and the
washer.
Refit the top drawer.
Before use, ensure that the strap is securely fixed to both the wall and the dresser.
1
234
The type of wall fixing you will require depends on the construction of the wall. See below for details.
If in doubt, seek professional advice.
Wood: If fixing to wood make
sure that it isn’t chipboard as
screws can easily pull away
the core structure.
Brick or masonry: Use
the wall plug, provided
you are sure that your
wall is sound.
Cavity wall: Special toggle
wall plugs needed.
Seek expert advice.
Washer x 2
Fabric strap
Plastic wall plug
(For brick or masonry wall use only)
Screw (25mm)Screw (15mm)
9
Assembly 11

Care and maintenance
Your furniture may be cleaned by wiping with a damp cloth and drying with a soft clean
cloth.
Do not use abrasives, bleach, alcohol or ammonia-based household polishes.
Take care when handling or moving the furniture. Careless handling may cause damage.
Regularly check that all fixings are tightened and that there are no broken or damaged
parts.
Safety notes
Warning: Do not leave your child unattended.
Keep children clear during assembly as pack contains small parts which may present a
choking hazard.
All assembly fixings should always be tightened properly. Care should be taken that no
screws are loose because a child could trap parts of their body, or clothing (e.g. strings,
necklaces, ribbons, dummies, etc) which could pose a risk of strangulation.
The changing area is suitable for use up to 12 months old or 11kg in weight.
Be aware of the risks of open fires and other such sources of strong heat, such as electric
bar fires, gas fires, etc. in the near vicinity of the dresser.
Do not use the changing unit if any of the parts are broken, torn or missing.
Any additional or replacement parts can only be obtained from the manufacturer or the
distributer.
This changing unit complies with BSEN 12221:2008 +A1:2013.
John Lewis Partnership
171 Victoria Street
London
SW1E 5NN
www.johnlewis.com
JLPRD
12/14