John Lewis Grace Bed User manual

Grace Bed
MTO
Thank you for purchasing this Grace Bed. Please read the instructions carefully before use to ensure safe
and satisfactory operation of this product.
King
Please check the pack contents before attempting to assemble this product. A full checklist of components is
given in this leaflet. If any components are missing, please contact customer services on 01244 689949 or email
[email protected].
This product is HEAVY. It should be assembled as near as possible to the point of use. TAKE CARE WHEN
LIFTING to avoid personal injury and (or) damage to the product.
This product takes approximately 40 MINUTES to assemble with 2 PEOPLE.
The fittings pack contains SMALL ITEMS which should be KEPT AWAY FROM YOUNG CHILDREN.
Read this leaflet in full before commencing assembl
Do not use power tools to assemble.
y.
PRE-ASSEMBLY PREPARATION
Please ensure instructions are read in full before attempting to assemble this product.
Necessary Tools
1/6

Fittings and parts checklist
A
B
C
D
E
M5 Allen Key x 1
M4 Allen Key x 1
Side Plastic Caps x 16
Centre Plastic Caps x 8
M6 X 25mm Bolt x 2
1
2
3
4
5
6
7
Headboard x 1
Footboard x 1
Side Rails x 2
Slats x 16
Centre Rail x 1
Legs x 4
2/6
Wide Slats x 16
F
G
Wide Centre Caps x 8
Wide Side Caps x 16

Head/Foot
Board
Preinserted Nut
Wooden Leg
(7) x 4
Step Two
Place Metal Brackets on Side Rails (3) over pre-inserted bolts in Headboard (1) and Footboard (2),
and hand-tighten bolts to loosely secure parts together. Do not tighten with the M5 Allen Key (B) until
you have inserted the Centre Rail in Step Three.
Step by step assembly instructions
Step One
Place Wooden Legs (7) into the holes in the underside of the Headboard (1) and Footboard (2) as
per diagram below and twist into place so they are fully secured.
BRACKET
SIDE RAIL
3
1
2
AND
1
3
3
2
1
2
BRACKET
SIDE RAIL
1
2
3
AND
3/6
LOOSELY SECURE PARTS
TOGETHER IN ORDER FOR
CENTRE RAIL TO FIT IN
STEP THREE

M4 (A)
M6 x 25mm (E)
Step Three
Insert Centre Rail (6) into the brackets in the centre of the Headboard (1) and Footboard (2). Push down
fully and secure in place using M6 x 25mm bolt (E). Tighten bolt with Allen Key M4 (A). You can
now tighten the bolts at the Side Rails from previous step (Step Two) so all fastenings are now tightened.
Centre Rail
(6)
S
T
E
P
1
M4 (A)
M6 x 25mm (E)
S
T
E
P
2
6
E. A.
M5
AFTER INSERTING CENTRE RAIL,
TIGHTEN ALL FIXINGS FULLY
INCLUDING BOLTS AT SIDE
RAILS (FROM STEP TWO)
M5
Bracket
Side Rail
3
1
2
AND
4/6
B.

2 Lines
Normal slats
2 Lines
Normal slat
2 Lines
Wide slats
2 Lines
Wide slats
2 Lines
Normal slats
2 Lines
Normal slats
4 Lines
Wide slats
ZONE 2
ZONE 1
ZONE 5
ZONE 7
ZONE 6
ZONE 4
ZONE 3
Diagram 1
Step Five
This bed is now ready to use.
5/6
D
G
4
5
(x8)
(x8)
4.
5.
C.
D
G.
F.
Side Caps x 16
.
Wide Centre Caps
x 8
Wide Side Caps
x 16
Wide Slats x 16
Slats x 16
Step Four
With the curved side facing upwards, insert 2 slats into a centre cap then into 2 side caps on either
end(x16). (Please note the Wide Slats must be inserted with the Wide Centre Caps (F) and Wide
Side Caps (G)). Repeat this process for all slats.
Note: Please see the Diagram 1 below to arrange the slat with the correct system).
4
4
C
F
5
5
Centre Caps x 8
F
G
G
D
D
4
4
5
5
C

Care and Maintenance
Safety Instructions
If you require any additional information or have any issues with this product please call the customer
services helpline on 01244 689949 or email [email protected].
Never drag furniture when moving it. Always lift it.
Periodically check all fixings to ensure none have come loose and re-tighten where necessary.
Please take care when handling or moving the furniture as careless handling may cause damage or injury.
Furniture can be dangerous if incorrectly installed. Any assembly should be carried out by a competent
adult.
No liability will be accepted for damage or injury caused by incorrectly installed or assembled furniture.
During assembly, children should be kept away from the product due to possible risk of injury.
Do not use this item if any components are missing or damaged.
It is recommended that care is taken when moving heavy objects to a new location to avoid
personal injury or damage to the furniture. Please be careful to retain all fittings when doing this.
This bed should be cleaned using a soft, damp cloth and dried immediately.
Do not use a very wet cloth or allow any liquid contact for a long period of time as this can permanently
damage the surface.
Do not use detergents and do not rub as this can cause permanent damage.
Always protect your bed from direct sunlight as this may accelerate the natural ongoing discolouration
process.
Bolts holding together the bed frame should be tightened regularly.
Please retain this information leaflet for future reference.
This product complies with BS EN 1725:1998.
6/6