John Lewis House Equate Single Cupboard User manual

John Lewis
House Equate Single Cupboard
Stock number: 84982002
Thank you for purchasing this House Equate single cupboard. Please read the instructions
carefully before use to ensure safe and satisfactory operation of this product
Pre-assembly preparation
Necessary Tools
Please check the pack contents before attempting to assemble this product. A full checklist of
components is given in this leaflet. If any components are missing, please contact the retailer
from whom you bought this product.
TAKE CARE WHEN LIFTING to avoid personal injury and (or) damage to the product.
This product takes approximately 45 MINUTES to assemble with 1 PERSON.
The fittings pack contains SMALL ITEMS which should be KEPT AWAY FROM YOUNG
CHILDREN.
Please assemble on a soft clean surface to avoid damages to your product

Fittings checklist
A
Cam stud
X16
F
Hinge
X2
B
Cam
X16
G
Hinge/KD block
screw12mm
X15
C
Wood dowel
X18
H
Cover caps
X8
D
KD block
X3
I
Plinth fixing screw
50 mm
X8
E
Nail glides
X4

Parts checklist
1
Top panel
X1
6
Back panel
X1
2
Left side panel
X1
7
Front/Back plinth
X2
3
Right side panel
X1
8
Left/Right plinth
X2
4
Shelf
X1
9
Bottom panel
X1
5
Door
X1

Step by step assembly instructions
Step One
Insert four cam studs (A) into the allocated holes in the top panel (1) and tighten clockwise with
a crosshead screwdriver. Make sure the cam studs are fixed in a right angle and do not overturn.
Step Two
Insert four cam studs (A) into each of the two side panels (2+3) as shown, and tighten
clockwise with a crosshead screwdriver. Make sure the cam studs are fixed in a right angle
and do not overturn.

Insert two wood dowels (C) into each end of the bottom panel (9) and into each end of the
shelf (4).
Note: Make sure the wooden dowels are inserted into the blind holes, and not into the cam
stud holes at the end of the panel.
Step Four
Fix the shelf (4) and the bottom panel (9) to the side panel (2). Insert cams (B) into the
allocated holes as shown and tighten gently clockwise with a screwdriver.
Do not overturn.
Step Three

Step Five
Gently slide the back panel (6) into the grove in the side panel (2) and bottom panel (9) as
shown.
Step Six
Connect the right hand side panel (3) to the shelf and bottom panel, then insert 4 cams (B) into
the allocated holes and tighten the cams clockwise with a screwdriver. Do not overturn.

Step Seven
Now connect the top panel (1) to the side panels. Then insert 4 cams (B) into the allocated
holes in the side panels, and tighten gently clockwise with a screwdriver.
Do not overturn.
Step Eight
Ensure that the cabinet is in a 90-degree straight angle, then slide three KD blocks (D) into the
grove in the side panels/bottom as shown. Insert three 12 mm screws (G) into the KD blocks
and tighten clockwise with a crosshead screwdriver.

Step Nine
Lay the two front/back plinths (7) and the two left/right hand side plinths (8) out on your
protected working surface as shown. Insert four cam studs (A) into the allocated holes in the
front/back plinths (7), and tighten clockwise with a crosshead screwdriver. Do not overtighten.
Then insert two wooden dowels into the center top holes in the front/back plinths (7), and four
wooden dowels into the ends of the side plinths (8).
Step Ten
Connect the front/back plinths (7) to the side plinths (8) as shown.

Step Eleven
Insert four cams (B) into the allocated holes and tighten gently clockwise with a screwdriver.
Do not overturn.
Step Twelve
With eight 50 mm screws (I), fix the plinth to the bottom panel and tighten the screws
clockwise with a crosshead screwdriver.

Step Thirteen
Lay the door down as shown and fix the two hinges (H) with 12 mm fixings screws (G). The
screws are tightened clockwise with a crosshead screwdriver.
Finally tap the four nail glides (E) onto the corners of the plinth.
Step Fourteen
Finally attach the cover caps (H) to the cams as shown.