John Lewis Rouen User manual

1/10
For product support or spare parts please call
the John Lewis Helpline;
T: 01244 689949
E: [email protected]
Rouen Storage Bed
PRE-ASSEMBLY PREPARATION
Please check the pack contents before attempting to assemble this product. A full checklist of components is
given in this leaflet. If any components are missing, please contact the John Lewis Helpline.
This product is HEAVY. It should be assembled as near as possible to the point of use. TAKE CARE WHEN
LIFTING to avoid personal injury and (or) damage to the product.
This product takes approximately 90 MINUTES to assemble with 2 PEOPLE.
The fittings pack contains SMALL ITEMS which should be KEPT AWAY FROM YOUNG CHILDREN.
Read this leaflet in full before commencing assembl
Do not use power tools to assemble.
y.
If you require any additional information or have any issues with this product please call the
John Lewis Helpline on 01244 689949 or email [email protected]
John Lewis
Please ensure instructions are read in full before attempting to assemble this product.
Necessary Tools
Thank you for purchasing this Rouen Storage Bed. Please read the instructions carefully before use to
ensure safe and satisfactory operation of this product.
King, Superking

2/10
Fittings and parts checklist
M8 Spring Washer x 10 pcs
M8 x 16mm Bolt x 8 pcs
M6 x 25mm Bolt x 6 pcs
M6 x 40mm Bolt x 8 pcs
Screw 3.5 x 30mm x 42pcs
Screw 4 x 18mm x 8pcs
Screw 4 x 50mm x 4pcs
M13 Spanner x 1 pcs
M8 Nut x 2 pcs
Wide Centre Caps x 8
Wide Side Caps x 16
A
B
C
F
G
D
E
J
K
L
M
O
N
H
I
M4 Allen Key x 1 pcs
M5 Allen Key x 1 pcs
Side Caps x 16 pcs
Centre Caps x 8 pcs
Fittings

3/10
Headboard x 1 Footboard x 1 Side Rails x 2
Slats x 16 Wide Slats x 16
Drawer Runner Base x 2 Drawer Centre Support x 1
Drawer Sides x 4 Drawer Fronts x 2 Drawer Backs x 2
Drawer Bottoms x 2
Centre Rail x 1
Wooden Legs x 4
Upholstered Drawer Panels x 2 Drawer Bottom Supports x 6
12 3
456
7 8 9
10 11 12
13 14 15
Metal Stopper x 4
Parts
17 16
Metal plates x 2

4/10
Step One
Step Two
Attach M8 Spring Washer (G) and M8 x 16mm Bolts (H) into the metal fixings onto both Drawer Runner Base (8)
(only for the top side). Insert the Drawer Runner Base (8) inside the bed frame as shown in step 2. Next, attach the
M8 Spring Washer (G) and M8 x 16mm Bolts (H) into the bottom side of metal fixing on the bottom supports.
Loosely tighten the bolts using M5 Allen Key (B).
M8 x 16mm
Bolt x 8
M8 Spring
Washer x 8
B.
M8 x 16mm
Bolt (H)
M8 Spring Washer
(G)
8
STEP 1
8
3
1
3
8
8
3
2
M5 Allen Key x 1
G. H.
1
2
BRACKET
SIDE RAIL
3
1
BRACKET
SIDE RAIL
2
3
Place metal bracket on Side Rails (3) over pre-inserted bolts in Headboard (1) and Footboard (2) and hand-tighten
to loosely secure parts together. Do not tighten bolts with M5 Allen Key (B) until you have inserted the Centre Rail
in Step Four.
LOOSELY SECURE PARTS
TOGETHER IN ORDER FOR
CENTRE RAIL TO FIT IN
STEP FOUR
LOOSELY SECURE PARTS
TOGETHER IN ORDER FOR
CENTRE RAIL TO FIT IN
STEP FOUR
3
8
8
Fig 2
M5 Allen Key
(B)
STEP 2

5/10
1
6
3
3
2
Screw
4 x 50mm x 4
Step Three
Step Four
1
3
3
2
8
9
8
8
9
9
x1
3
Attach Drawer Centre Support (9) to Drawer Runner Base (8) and secure into place using Screws 4 x 50mm (K) as
shown in the diagram below.
1
M4 Allen Key (A)
M6 x 25mm (I)
M4 Allen Key x 1 M6 x 25mm Bolt x 2
A. I.
AFTER INSERTING CENTRE
RAIL, TIGHTEN ALL FIXINGS
FULLY INCLUDING BOLTS
AT SIDE RAILS (FROM
STEP ONE)
K.
Cross head
Screw Driver
Screw 4 x 50mm (K)
Screw 4 x 50mm (K)
S
T
E
P
1
S
T
E
P
2
Insert Centre Rail (6) into the brackets on the Headboard (1) and Footboard (2). Push down fully and secure in
place using M6 x 25mm Bolts (I). Tighten using M4 Allen Key (A). You can now tighten the bolts with M5 Allen Key (B)
at the Side Rails from Step One so all fastenings are now tightened.

6/10
Step Five
Step Six
Insert the Front Legs (7)x2 into the pre-drilled holes on the underside of the Headboard (1) and twist to secure, as
shown in the diagram below.
Legs x 2
I.
7.
M8 Nut x 2
M13 Spanner x 1
Screw
3.5 x 30mm x 2 M6 X 25mm Bolt x 4
7
Legs x 2
16.
Metal plates x 2
M8 Spring
Washer x 2
A.
M4 Allen Key x 1
F
o
r
H
e
a
d
b
o
a
r
d
O
n
l
y
3
1
L.M.N.
Attach the Metal Plate (16) to the bottom of the Footboard (2) using Bolts M6 X 25mm (I) x2. Do not tighten the bolts
until you make adjustment for the screw hole at the Side Rail (3). Insert Wooden Leg (7) into the bottom of the
Metal Plate (16) using M8 Spring Washer (G) and M8 Nut (M). Hold the M8 Nut (M) using M13 Spanner (N) and twist
the Wooden Leg (7) to secure in place. Repeat for other leg.
G. 7.
x2
For Footboard Only
M6 x 25mm (I)
1
16
M4 (A)
M6 x 25mm (I)
M6 x 25mm (I)
1
M4 (A)
M6 x 25mm (I)
16
3.5 x 30mm (L)
3.5 x 30mm (L)
M13 Spanner (N)
M8 Nut (M)
M8 Spring
Washer (G)
16
7
1
STEP 1
STEP 2
AFTER INSERTING BOLT M6 x 25MM,
MAKE ADJUSTMENT FOR SCREW HOLE,
THEN INSERT THE SCREW 3.5 X 30MM.
TIGHTEN THE BOLT M6 x 25MM
FIXINGS FULLY.
TWIST WOODEN LEG ONLY
WITHOUT MOVING THE M8 NUT,
SPRING WASHER AND SPANNER
Twist the wooden leg
3
3
3
Yellow sticker
face down

7/10
Step Eight
Attach Upholstered Front Panel (14) to drawer and tighten together using M6 x 40mm Bolt (J). Tighten with
M4 Allen Key (A). Slide drawers into both sides of the bed frame. The bed is now ready for use.
M6 x 40mm x 8
M4 Allen Key x 1
A. J.
14
x2
14
Step Seven
3.5 x 30mm
x 40
Cross Head
Screw Driver
L.
To construct the drawers, fix Drawer Front (11) with one end of each Drawer Bottom Support (15) using
Screws 3.5 x 30mm (L) as shown in Fig.1, then fix the Drawer Sides (10) to the Drawer Front (11). Next,
insert Drawer Bottom (13) and then fix Drawer Back (12) using Screws 3.5 x 30mm (L) as shown in Fig.2.
Finally, secure the other end of the Drawer Bottom Support (15) to the other side of the drawer and tighten
using a cross head screw driver.
(x2) (x2)
11
11
10
12
13
15
10
(x2)
10
10
15
15
15
Fig. 1 Fig. 2 Fig. 3

8/10
Step Nine
Attach Metal Stopper (16) to the Drawer Runner Base (8) using Screw 4 x 18mm (O).
Screw 4 x 18
x 8
16.O.
8
16
10
4x
Metal Stopper x 4

2 Lines
Normal slats
2 Lines
Normal slat
2 Lines
Wide slats
2 Lines
Wide slats
2 Lines
Normal slats
2 Lines
Normal slats
4 Lines
Wide slats
ZONE 2
ZONE 1
ZONE 5
ZONE 7
ZONE 6
ZONE 4
ZONE 3
Diagram 1
9/10
Step Eleven
The bed is now ready for use.
D
F
4
5
(x8)
(x8)
4.
5.
C.
D
F.
E.
Side Caps x 16
.
Wide Centre Caps
x 8
Wide Side Caps
x 16
Wide Slats x 16
Slats x 16
With the curved side facing upwards, insert 2 slats into a centre cap then into 2 side caps on either
end(x16). (Please note the Wide Slats (5) must be inserted with the Wide Centre Caps (E) and Wide
Side Caps (F)). Repeat this process for all slats.
Note: Please see the Diagram 1 below to arrange the slat with the correct system).
Centre Caps x 8
E
F
F
D
D
4
4
5
5
C
Step Ten
4
4
C
E
5
5

10/10
Care and Maintenance
Safety Instructions
If you require any additional information or have any issues with this product please call
the John Lewis Helpline on 01244 689949 or email [email protected]
John Lewis Partnership 171 Victoria Street, London, SW1E 5NN.
www.johnlewis.com
Never drag furniture when moving it. Always lift it.
Periodically check all fixings to ensure none have come loose and re-tighten where necessary.
Please take care when handling or moving the furniture as careless handling may cause damage or injury.
Furniture can be dangerous if incorrectly installed. Any assembly should be carried out by a competent
adult.
No liability will be accepted for damage or injury caused by incorrectly installed or assembled furniture.
During assembly, children should be kept away from the product due to possible risk of injury.
Do not use this item if any components are missing or damaged.
It is recommended that care is taken when moving heavy objects to a new location to avoid
personal injury or damage to the furniture. Please be careful to retain all fittings when doing this.
This Rouen Storage Bed should be cleaned using a soft damp cloth and dried immediately.
Do not use a very wet cloth or allow any liquid contact for a long period of time as this can permanently
damage the surface.
Do not use detergents and do not rub as this can cause permanent damage.
Always protect your bed from direct sunlight as this may accelerate the natural ongoing discolouration
process.
Bolts holding together the bed frame should be tightened regularly.
Please retain this information leaflet for future reference.
This product complies with BS EN 1725:1998.