John Lewis 803/45201 User manual

Owen Bed
PRE-ASSEMBLY PREPARATION
Please check the pack contents before attempting to assemble this product. A full checklist of components is
given in this leaflet. If any components are missing, please contact the John Lewis Helpline.
This product is HEAVY. It should be assembled as near as possible to the point of use. TAKE CARE WHEN
LIFTING to avoid personal injury and (or) damage to the product.
This product takes approximately 40 MINUTES to assemble with 2 PEOPLE.
The fittings pack contains SMALL ITEMS which should be KEPT AWAY FROM YOUNG CHILDREN.
Read this leaflet in full before commencing assembly.
If you require any additional information or have any issues with this product please call the
John Lewis Helpline on 01244 689949 or email [email protected]
Double
Stock code white: 803/45201
black: 803/45301
grey/taupe: 803/45401
brown: 803/45501
John Lewis
For product support or spare parts please call
the John Lewis Helpline;
T: 01244 689949
E: [email protected]
Please ensure instructions are read in full before attempting to assemble this product.
Necessary Tools
Thank you for purchasing this Owen Bed. Please read the instructions carefully before use to ensure safe
and satisfactory operation of this product.
1/6
King
Stock code white: 803/45202
black: 803/45302
grey/taupe: 803/45402
brown: 803/45502

Fittings and parts checklist
A
B
C
D
E
F
G
M5 Allen Key x 1
M4 Allen Key x 1
Side Plastic Cap x 30
Centre Plastic Cap x 15
JCBC M6 X 25mm Bolt x 2
JCBC M6 X 70mm Bolt x 8
Washer M6 x 8
1
2
3
4
5
6
Headboard x 1
Footboard x 1
Side Rails x 2
Slats x 30
Centre Rail x 1
Legs x 4
2/6

Step Two
Place the pre-attached metal fixings on the Side Rails (3) over the pre-inserted bolts in Headboard (1) and
Footboard (2), and hand-tighten bolts to loosely secure parts together. Do not tighten with the M5 Allen Key (B)
until you have inserted the Centre Rail in Step Three.
Step by step assembly instructions
Step One
Place Legs (6) over the holes on the underside of the Headboard (1) and Footboard (2) as per below drawing.
Insert M6 x 70mm Bolts (F) and Washer M6 (G) to fix each leg in place and tighten using Allen Key M4 (A)
provided.
M5
M6 x 70 bolt
M6 x 70 bolt
(6) x 4
M6x70 (8)M4
Allen Key
Bed Leg
Preinserted Nut
Head/Foot
Board
M6 x 70 bolt
M6 x 70 bolt
M6 x 70
Washer M6
Bracket
Side Rail
1
2
3
AND
1
23
3
G.
Washer M6 (8)
F.A.
B.
3/6
M5
Bracket
Side Rail
3
1
2
AND
M5
LOOSELY SECURE PARTS
TOGETHER IN ORDER FOR
CENTRE RAIL TO FIT IN
STEP THREE

M4
M6x25mm
Step Three
Lower the Centre Rail (5) into the brackets in the centre of the Headboard (1) and Footboard (2).
Push down fully and secure in place using M6 x 25mm Bolt (E) and tighten with Allen Key M4 (A). You can
now tighten the bolts at the Side Rails from previous step (Step Two) so all fastenings are now tightened.
Step Four
Starting at the Headboard (1), attach the Centre Plastic Holders (C) into the holes along the Centre Rail (5).
Ensuring the Wooden Slats (4) have the curved side facing up, place the Side Cap (D) onto one end of the
Wooden Slat (4). Insert the other end of the Wooden Slat (4) into the Centre Plastic Holder (C), then insert
the Side Cap (D) onto the Side Rail (3) into the pre-drilled holes.
Side Plastic Cap (30 pcs)
Centre Plastic Clip (15 pcs)
Bent Slat (30 pcs)
Centre Rail
S
T
E
P
1
M4
M6 x 25mm (E)
S
T
E
P
2
4.
C.
D.
5
E. A.
4/6
C
D
4
AFTER INSERTING CENTRE RAIL,
TIGHTEN ALL FIXINGS FULLY
INCLUDING BOLTS AT SIDE
RAILS (FROM STEP TWO)

Step Five
This bed is now ready to use.
5/6

Care and Maintenance
Safety Instructions
This Owen Bed should be cleaned using a soft damp cloth and dried immediately. Do not
use a very wet cloth or allow any liquid contact for a long period of time as this can permanently
damage the surface.
Do not use detergents and do not rub as this can cause permanent damage.
Always protect your bed from direct sunlight as this may accelerate the natural on-going discolouration
process.
Screws holding together the bed frame should be tightened regularly.
Please retain this information leaflet for future reference.
Never drag furniture when moving it. Always lift it.
Periodically check all fixings to ensure none have come loose and re-tighten where necessary.
Please take care when handling or moving the furniture as careless handling may cause damage or injury.
Furniture can be dangerous if incorrectly installed. Any assembly should be carried out by a competent adult.
No liability will be accepted for damage or injury caused by incorrectly installed or assembled furniture.
During assembly, children should be kept away from the product due to possible risk of injury.
Do not use this item if any components are missing or damaged.
It is recommended that care is taken when moving heavy objects to a new location to avoid
personal injury or damage to the furniture. Please be careful to retain all fittings when doing this.
This product complies with BS EN 1725:1998.
6/6
If you require any additional information or have any issues with this product please call
the John Lewis Helpline on 01244 689949 or email [email protected]
John Lewis Partnership 171 Victoria Street, London, SW1E 5NN.
www.johnlewis.com