John Thomas BOMBAY MEDIA CENTER TV-59 User manual

ITEM NO.: TV-59
REVISED MAR 07, 2016
Printed in Vietnam
- 1 -
ASSEMBLY INSTRUCTIONS
Description
Item No.
: BOMBAY MEDIA CENTER
: TV-59

ITEM NO.: TV-59
REVISED MAR 07, 2016
Printed in Vietnam
- 2 -
Thank you for purchasing this quality product. This product has been designed for easy assembly
and constructed for durability. All parts were checked prior to packaging to insure quality. Prior to
beginning assembly, however, make sure all parts and hardware are included and free of obvious
defect. If a part is missing or defective, please contact the store where purchased. If hardware is
missing, or you need help with assembly, please call toll free 888-944-8396.
IMPORTANT NOTE:
-Place all wooden parts on a clean and smooth surface such as a rug or carpet to avoid the
parts from being scratched.
-Remove all wrapping material, including staples & packing straps before you start to
assemble.
-DO NOT tighten all screws and bolts until completely assembled.
-Keep all hardware parts out of reach of children.
WARNING:
Long exposure to rubber or soft plastic may cause a chemical reaction and damage the finish of
your product. Protect the surface of the product with cloth if you are using any product with rubber
feet or base.
BEFORE ASSEMBLY
ASSEMBLY TOOLS REQUIRED
NOT INCLUDED

ITEM NO.: TV-59
REVISED MAR 07, 2016
Printed in Vietnam
- 3 -
When unpacking, please be careful not to discard any parts with the packaging. Before continuing,
please make sure you have the following parts:
NO
Description
Qty
Sketch
NO
Description
Qty
Sketch
A
Top
1
B
Side frame
(L-R)
2
C
Cross Bar
1
D
Shelf
1
E
Drawer
front
1
F
Drawer side
(L-R)
2
G
Drawer
back
1
H
Drawer bottom
1
I
Back
1
J
Drawer supporter
2
PART LIST

ITEM NO.: TV-59
REVISED MAR 07, 2016
Printed in Vietnam
- 4 -
When unpacking, please be careful not to discard any parts with the packaging. Before continuing,
please make sure you have all of the following hardware:
NO
Description
Qty
Sketch
NO
Description
Qty
Sketch
1
Bolt
(M6x35mm)
8
2
Flat washer
(ɸ6.5x19mm)
8
3
Lock washer
(6.5x11mm)
8
4
Allen key
(M4x80mm)
1
5
Cam-bolt
2
6
Cam-lock
2
7
Short screw
(M3.5x15mm)
10
8
Long screw
(M4x25mm)
16
9
Long pan head screw
*Metal knob: (M4x22mm)
*Woodenknob: (M4x25mm)
2
10
Knob
2
METAL KNOB
(30 x 30mm)
GOES WITH
FINISHED ITEM
ONLY.
HARDWARE LIST

ITEM NO.: TV-59
REVISED MAR 07, 2016
Printed in Vietnam
- 5 -
Attach top (A) and shelf (D) to side frames (B) with bolts (1) and washers (2) and (3) as shown below.
Tighten with Allen key (4).
Attach cross bar (C) to side frames (B) with cam-bolts (5) and cam-locks (6) as shown below. Tighten
with a screwdriver.
Attach back (I) to the unit with screws (7) as shown below. Tighten with a screwdriver.
STEP 1
STEP 2

ITEM NO.: TV-59
REVISED MAR 07, 2016
Printed in Vietnam
- 6 -
Attach drawer bottom (H), drawer back (G) and drawer sides (F) to the drawer front (E) with screws
(8). Tighten with a screwdriver.
Then attach drawer supporters (J) underneath drawer with screws (8) as shown below. Tighten with a
screwdriver.
Attach knobs (10) to front of drawer with pan head screws (9) as shown below. Tighten with a
screwdriver.
STEP 3
STEP 4

ITEM NO.: TV-59
REVISED MAR 07, 2016
Printed in Vietnam
- 7 -
Carefully put the drawer (from step 4) into the unit.
STEP 5