John Thomas OT-66 User manual

ITEM NO
:
OT
-
66
REVISED NOV 06, 2014
Printed in Vietnam
- 1 -
ASSEMBLY INSTRUCTIONS
Description
Item No.
:
2 DRAWER COUNTRY ACCENT TABLE
: OT-66

ITEM NO
:
OT
-
66
REVISED NOV 06, 2014
Printed in Vietnam
- 2 -
Thank you for purchasing this quality product. This product has been designed for easy assembly and
constructed for durability. All parts were checked prior to packaging to insure quality. Prior to beginning
assembly, however, make sure all parts and hardware are included and free of obvious defect. If a part is
missing or defective, please contact the store where purchased. If hardware is missing, or you need help with
assembly, please call toll free 888-944-8396.
IMPORTANT NOTE:
-Place all wooden parts on a clean and smooth surface such as a rug or carpet to avoid the parts from
being scratched.
-Remove all wrapping material, including staples & packing straps before you start to assemble.
-DO NOT tighten all screws and bolts until completely assembled.
-Keep all hardware parts out of reach of children.
WARNING:
Long exposure to rubber or soft plastic may cause a chemical reaction and damage the finish of your
table. Protect the surface of the table with cloth if you are using any product with rubber feet or base.
-
BEFORE ASSEMBLY
ASSEMBLY TOOLS REQUIRED
NOT INCLUDED

ITEM NO
:
OT
-
66
REVISED NOV 06, 2014
Printed in Vietnam
- 3 -
PART
LIST
When unpacking, please be careful not to discard any parts with the packaging. Before continuing, please
make sure you have the following parts.
NO
Description
Q
ty
Sketch
NO
Description
Q
ty
Sketch
A Top 1 B
Side panel
(L – R)
2
C
Back panel 1
D Front apron 1
E Back apron 1 F
Upper
Drawer front 1
G
Upper
Drawer side
2
H
Upper
Drawer back
1
I
Lower
Drawer front
1
J
Lower
Drawer side
2
K
Lower
Drawer back
1
L Drawer
bottom 2
M Rail 2

ITEM NO
:
OT
-
66
REVISED NOV 06, 2014
Printed in Vietnam
- 4 -
HARDWARE LIST
When unpacking, please be careful not to discard any parts with the packaging. Before continuing, please
make sure you have all of the following hardware:
NO Description Qty Sketch NO Description Qty Sketch
1 Bolt
( M6 x 35mm) 4
2 Lock Washer
(6.5 x11mm) 4
3 Flat Washer
(6.5 x19mm) 4
4 Screw
(M4x30mm) 24
5 Pan head screw
(M4 x 25 mm) 3
6 Knob
(38x30mm) 3
7 Allen key
(K4x80mm) 1
STEP 1
Attach side panel (B) to top (A) with bolts (1), and washers (2) and (3) as shown below. Tighten with Allen key (7).

ITEM NO
:
OT
-
66
REVISED NOV 06, 2014
Printed in Vietnam
- 5 -
STEP 2
Slide back panel (C) into the grooves as shown below.
STEP 3
Attach front apron (D) and back apron (E) to the side panel (B) with screws (4) as shown below.
Tighten with a screwdriver.
Attach side panel (B) to top (A) with bolts (1), and washers (2) and (3) as shown below. Tighten with
Allen key (7).

ITEM NO
:
OT
-
66
REVISED NOV 06, 2014
Printed in Vietnam
- 6 -
STEP
4
Attach drawer side (G) to drawer front (F) and drawer back (H) with screws (4). Tighten with a
screwdriver.
Slide drawer bottom (L) into the grooves as shown below.
Then attach drawer side (G) to the unit with screws (4) as shown below. Tighten with a screwdriver.
Attach rail (M) to drawer front (F) and drawer back (H) with screws (4). Tighten with a screwdriver.
STEP
5
Attach drawer side (J) to drawer front (I) and drawer back (K) with screws (4). Tighten with a
screwdriver.
Slide drawer bottom (L) into the grooves as shown below.
Then attach drawer side (J) to the unit with screws (4) as shown below. Tighten with a screwdriver.
Attach rail (M) to drawer front (K) and drawer back (I) with screws (4). Tighten with a screwdriver.

ITEM NO
:
OT
-
66
REVISED NOV 06, 2014
Printed in Vietnam
- 7 -
STEP
6
Put drawers into the unit as shown below.
Attach knobs (6) to front of drawer with pan head screws (5). Tighten with a screwdriver.