Johnson & starley Hi-spec j32p User guide

1 AirFilter

2 Air circulating fan

3 Heat exchanger access cover

4 Data plate

5 Time control

6 Multifunctional control

7 FanDelayControl/Limit Switch

8 Pilot burner

9 Burner Assembly

10 Gas connection

11 Heat shield

12 Piezo igniter unit

13 Spillage monitoring Device (TTB)

(Air heater)

14 Spillage monitoring Device (TTB)

(Water Heater)

TheseapplianceshavebeentestedandcertifiedbyBGTechnologyforusewithPROPANEgasG31.

Note: If a HIJAN 6P circulator is fitted, the relevant Installation, Commissioning and Servicing instructions provided with that

appliance must also be observed.

1. BRIEFDESCRIPTION

HI-SPEC J32P and HI-SPEC J32RP

WARM AIR HEATERS

with Conventional Control

INSTALLATION, COMMISSIONING& SERVICING INSTRUCTIONS

G.C. No 42 451 07 HI-SPEC J32P

G.C. No 42 451 08 HI-SPEC J32RP PublicationNo.ZZ982/7

February 2007

These instructions are to be left with the User or adjacent to the Gas Meter

Fig. 1

1.1 HI-SPEC J32P is an open-flued, fan assisted downflow, ducted warm air heater, supplied with conventional control. A

HIJAN 6P circulator is available as an option. HI-SPEC J32RP, which has an integral rear rising duct is also available as

an option. A Spillage Monitoring Device (TTB) is fitted which senses the temperature in the draught diverter, and shuts

down the appliance when this temperature rises due to the presence of flue gases.

1.2 The Air heater output is 8.30kW (29.88MJ/h, 28,320Btu/h) . “Summer air circulation” of unheated air is available by

manual selection (see User’s Instructions). HIJAN 6P output is 3.56kW (12.8MJ/h, 12,150Btu/h).

THIS APPLIANCE CONFORMS TO BS EN 55014

JohnsonandStarleypridesitselfonitsabilitytosupplysparepartsquicklyandefficiently.Ifyouhaveaprobleminobtaininga

sparepart,pleasecontactJohnsonandStarleySparesDepartmentattheaddressbelow.

JOHNSON&STARLEYLTD.

Telephone: (01604) 762881 RhosiliRoad,

Brackmills,

Fax: (01604) 767408 NorthamptonNN47LZ

712

10. SHORTLIST OFSPARES

HI-SPEC J32P and HI-SPEC J32RP

KEY G.CNo MFR’S No DESCRIPTION QTY

1 245501 1000-0500370 Fan Assembly 1

2 H26-712 1000-0709640 Multifunctional Control 1

HoneywellV8600C1129

BOS02397/2 Pilot Burner 1

1000-0701440 PilotInjector (No 19) 1

1000-0704730 Pilot Feed Pipe 1

390210 BOS01970 Igniter Electrode 1

BOS02394 Igniter Lead 1

381626 1000-0704830 Thermocouple 1

4 378466 BOS02031 TimeControl 1

5 1000-0708020 Burner BarAssembly 1

6 1000-0708040 MainInjector( Bray 1.78mm ) 1

7 395945 1000-0700570 PiezoUnit (High Energy) 1

8 245509 1000-0513820 Fuse T3.15A anti-surge 1

13 386634 1000-0503730 SpillageMonitor Device (TTB) 1

14 J304-0511000 ElectricalPanel 1

15 245520 1000-0516125 FanDelay/LimitControl 1

16 1000-0515190 Transformer Fan Speed 1

17 245525 1000-0515730 Transformer24 volt 1

18 245413 1000-0511760 Relay Module 1

19 J304-0769000 TTBAssembly (water heater) 1

Installationshallbeinaccordancewith the current editionsof:-

Building Standards (Scotland) (Consolidation) Regulations

Building Regulations

Gas Safety (Installation and Use) Regulations (as amended)

BS 7671 Institute of Electrical Engineers (I.E.E.) Wiring Regulations

BS 5482 Pt. 1 Domestic Butane- and Propane-gas-burning installations.

BS 5440 Pt. 1 (Flues for Gas Appliances)

BS 5440 Pt. 2 (Air Supply for Gas Appliances)

BS 5864 Installation of Gas Fired Ducted Air Heaters

British System Design Manual “Gas Fired Warm Air Heating”

Model and Local Authority Bye-laws

BS 5546 Installation of Domestic Hot Water Supplies.

IMPORTANT:STATUTELAWDEFINESTHATALLGASAPPLIANCESMUSTBEINSTALLEDBYCOMPETENTPER-

SONS,(i.e.CORGIREGISTEREDINSTALLERS)INACCORDANCEWITHTHE GAS SAFETY(INSTALLATIONAND

USE)REGULATIONS(CURRENTEDITION).FAILURETOCOMPLYWITHTHESEREGULATIONSMAYLEADTO

PROSECUTION.

2. HEATER COMPARTMENTAND CLEARANCES (SeeBS5864)

2.1 IMPORTANT: If the heater is to be fitted to an existing base duct (warm air plenum), always ensure that installation is

carried out such that the rear left hand corner of the heater is aligned with the rear left hand corner of the base duct, so

that any overhang or blanking off will be at the front and/or right hand side. In any event, blanking plates must be

mechanically secured and all joints sealed.

2.2 When the heater is fitted into a compartment, a minimum clearance from the compartment walls of 3mm at the

sides and rear, and 75mm (3 in) at the front must be left. Consideration should also be given to the space required for the

removal and replacement of the filter tray and the entry of the gas, water and electrical supplies. If gas and /or water

connections are made from a side entry, a minimum clearance of 75mm is required at that side.

2.3 For service access, a minimum of 450mm (18ins) is required at the front of the heater. Space must also be allowed, in a

compartment installation, to permit the removal of the heater. The clearance between the appliance and the compartment

should be not less than 75mm (3 in). However, if clearances are less than 75mm, the internal surface of the compartment

must be lined with non-combustible material. The compartment must be of a fixed rigid structure.

2.4 In airing cupboard installations, the part used as the air heater compartment must comply with the relevant section of

BS5864 and must be completely separated by either a non-combustible partition or a perforated metal partition with the

perforations not exceeding 13mm (1/2in). The secondary flue must be a tight fit where it passes through the partition and

must be suitably protected (see BS5440:Part 1).

2.5 In free-standing installations, (see instructions packed withTC32 or TC32RTop Closure Kit), only one or two walls will be in

close proximity to the air heater; these must be non-combustible.

2.6 If theAir Heater is to be installed onto a combustible surface, a suitable base tray is required (BT32 for J32 model

appliances) is required. However, when a base duct is used, this provides sufficient protection for combustible material and

no further insulation is required.

2.7 For Slot Fix applications (see instructions packed with the Slot Fix Kit), it is important to ensure that the draught diverter

relief is maintained on both sides of the application.

3. VENTILATIONANDCOMBUSTIONAIR

3.1 The room or internal space in which the heater is installed requires a permanent air vent of minimum effective area

41cm2 (6in2). The air vent should be either direct to outside air or to an adjacent room or internal space (other than a

toilet or bathroom) that itself has an equivalent air vent direct to outside.

3.2 Combustion air may be introduced, via a 100mm (4in) nominal bore pipe, connected to a return air duct or plenum from

a ventilated area and fitted with a lockable damper. The damper should be adjusted to control combustion airflow to

0.0099m3/s(21cfm), (i.e.1.26m/s [250ft/min] velocityin a100mm [4in] borepipe). If thisarrangement isused, a non-

closeable warm air register MUST be provided in the same area as the front of the air heater or heater compartment if a

return air grille is not located in that area.

3.3 When installed in a compartment, two permanent ventilation openings into the compartment are required, one at high

level and one at low level, both communicating either directly with outside air or with a ventilated room or space. The

minimum effective areas specified in Table 1 are related to the rated heat input of the Air Heater, and assuming that a

HIJAN 6P circulator is fitted.

3.4 If any room or area from which air is drawn for ventilation or combustion contains an extract fan, the permanent vents

must be sized to ensure that the operation of the appliance(s) at full rate is/are not adversely affected. A spillage test as

specified in sub-para 6.8 (Safety Checks) is carried out and any remedial work undertaken.

Fig. 7, PRINCIPALDIMENSIONS (mm)

VENTILATED Low level grille 288cm2(44in2)

FROMINSIDE

BUILDING Highlevelgrille 144cm2(22in2)

VENTILATED Low level grille 144cm2(22in2)

FROMOUTSIDE

BUILDING Highlevelgrille 72cm2(11in2)

Table1:MinimumEffectiveAreas

4. DUCTSYSTEM

(See British Design Manual - Gas fired WarmAir Heating)

4.1 RETURNAIR

4.1.1 All return air shall be POSITIVELYducted from outside the compartment to the top of the unit via a return air

duct, or if appropriate, using a J & S Side Return Air Kit, and mechanically secured. It is recommended that the

return air duct be not routed directly from the main living area, but from a convenient central area serving the

remainder of the dwelling.

4.1.2 The return air system should be constructed of fire-resistant material. The flue shall not be run through an area

serving as a return air path. It is extremely important that the correct size of return air grilles and ducting is used.

For heaters on maximum output the return air duct size should not be less than the equivalent of 250mm x 200mm

(10" x 8"). If flexible duct is used the duct diameter should not be less than 300mm (12") dia. The return air

grille should have a free area of not less than 860cm2(137in2).

4.1.3 An adequate and unobstructed return air path is essential from areas not served by a directly ducted return and to

which warm air is delivered. All such rooms should be fitted with relief grilles which have a free area of

0.0088m2/kW (1in2/250Btu/h) of heat supplied to the room. The only exceptions are kitchens, bathrooms and

WC.’s.

4.1.4 The return air duct should allow for ease of removal for access to the flue.

4.1.5 All duct work in the room or internal space in which the heater is installed shall be mechanically secured, and

sealed with ducting tape.

4.2 WARMDELIVEREDAIR

4.2.1 All duct work, including riser ducts, should be fully insulated with 50mm (2in) fibreglass or similar. If short

extended duct runs are taken below floor level these should be similarly insulated, and in addition wrapped with a

sound vapour proof barrier, and protected from crushing.

4.2.2 The duct system should be carefully designed (as given in the guidelines in the British System Design Manual) to

suit the needs of its specific heating requirements and building layout. The type of duct system, (i.e. radial/

extended plenum/stepped) should be installed using the least number of fittings to minimise airflow resistance.

The base duct, which equalises the air pressure to supply ducts, shall be constructed to support the weight of the

heater, which shall be secured to the plenum with screws on at least two sides, and sealed using self-adhesive

foam strip, ducting tape or sealing compound. All ducting and blanking plates shall be mechanically secured and

sealed.

5. INSTALLATION REQUIREMENTS

Note: For circulator Installation Instructions, refer to the relevant instructions provided with the circulator.

5.1 FLUES(seeBritish Standards BS 5440Pt. 1 Flues)

5.1.1 All joints shall be soundly sealed.

5.1.2 The flue should be kept as short and warm as possible.

5.1.3 Sufficient support brackets shall be installed to bear the weight of the total flue system.

5.1.4 The spigot connection of the heater draught diverter will accept internally the spigot end of a non-asbestos flue

to BS 567 or twin wall metal flue to BS 715 of nominal 100mm (4in) diameter.

5.1.5 A split collar should be fitted to provide for flue maintenance or inspection.

5.1.6 The flue shall be in accordance with the Building Regulations and British Gas Materials and Installations

specification (3rd edition) with regard to clearance and shielding from combustible materials.

5.1.7 All materials shall be in accordance with Building Regulations requirements.

Fig.6, FUNCTIONALDIAGRAM

FELV * Connection

Timed

230V

Cont.

24V

Room Thermostat

Water Heater

(Optional)

Water Pump

(Optional)

Limit Switch

Multi-functional

Control 230V

Fan Delay

Control

Cleanflow

(Optional)

Wire colour code where indicated

*FELV Functional Extra-Low Voltage

NOTES:-

red-----------r

blue---------b

black-------bk

brown------br

white-------w

grey-------gy

orange---or

violet------v

yellow-----y

black/white------bk/w

purple/red-------p/r

green/yellow----g/y

CLOCK

Link

p/r

230V 50Hz

Supply L

AIR

HTR.

WATER

HTR.

Voltage

Selector

TX1

Summer

Air Flow

Limit

Switch

Fan Delay

Control

Fan

230V

PUMP

230V

(Optional)

(See

note)

(Optional)

Comm.

n/o

24V

Cleanflow

Air

Cleaner

Water

Htr

T500mA

Relay Module

24V Thermostat

(Not Fitted)

230V

Multi-functional Control

br b

Butt

Connector

Spill

Switch

(TTB)

ON S1

OFF

EXTERNAL PROG.

OPTION

NO CLOCK

OPTION

Park S8 when no

water htr. or

for ext. prog.

C1 230V

Timed

230V Cont.

AH(S5)

Timed

230V

Continuous C2

T3.15A

FUSE br

TX2

24V

Park conns when no

clock fitted or for

external prog.

If Superjan fitted remove red wire link

between terminals 10 &12

5.1.8 The flue should run as vertically as possible. Horizontal runs should be avoided if at all possible and any

directional change should be as gentle as possible. If there is any doubt about the flue configuration, the

equivalent flue height should be determined (see 5.1.10).

5.1.9 If the appliance to be fitted is a replacement, the old appliance should be checked for signs of spillage prior to

commencement of the installation and appropriate action taken, (i.e. check flue system and renew as necessary).

5.1.10 It is recommended that at least 600mm of vertical flue should be provided above the appliance (for new

installations this shall be incorporated into the flue design). However, when carrying out replacement

installations, an existing flue system may be encountered, where the vertical flue above the appliance to the first

bend is less than 600mm. In the first instance, the installer must judge whether this distance can be achieved

practicably by some means. Where this is not practicable, the existing flue system may be used, providing there is

no evidence of spillage from the old appliance (see 5.1.9 above). Every effort must be made, however, to ensure

that the existing flue complies in every other way to BS 5440 Part 1, including the visual inspection, flue flow and

spillage test described in 4.3.2 of the above standard. Flue configurations may be assessed in terms of equivalent

vertical height - details are given below. For air heaters, the minimum equivalent vertical height is 1 metre. The

installer must make a judgement based on his knowledge and experience and the examination and testing

described above as to whether an existing flue system can be used.

Note: Ventilation of the compartment, room or internal space in which the appliance is to be installed must be checked

for compliance with the requirements of BS 5440 Part 2 ( Ref. Section 3 of these instructions) and upgraded as

necessary.

5.1.11 Calculationmethodforfluesizing:(fromBS5440:Part1,AppendixA)

a. This appendix provides a procedure for estimating whether a given flue design is likely to ensure full

clearance of combustion products.

b. The procedure is based on calculating the ‘equivalent height’ of the flue under consideration, (i.e. that

height of the straight vertical circular flue pipe of specific size which will produce the same flow rate as

the flue under consideration). The equivalent height is calculated from the formula:

(Ki+ Ko )e

He= Hax

(Ki+ Ko)a- KeHa+ Sum K

where:

Heis the height of the equivalent flue;

Ha is the vertical height of the actual or proposed flue;

Kiis the inlet resistance of the flue;

Ko is the outlet resistance from the flue;

subscript e refers to the equivalent flue diameter;

subscript a refers to the actual or proposed flue diameter;

Keis the resistance per unit length of the equivalent flue;

Sum K is the resistance (other than the inlet and outlet resistance) of the actual or proposed flue.

Note: K and Sum K are obtained from Table 2. Koand Kiare obtained from Table 3.

c. Table 2 gives resistance factors for common flue components for use in the formula. Table 3 contains the

appropriate inlet and outlet flue resistances, ( the flue is likely to be satisfactory of its equivalent height

exceeds1m).

417

Fig. 5, CIRCUIT DIAGRAM

20 19 18 17 16 15 14 13 12 11 10 9 87 654 32 1

bk bk bbrrbr br brbb

0V NL LNLN

GE T

24V

Cleanflow

Fan

Delay

Control

230v

Multi-

functional

control

230v

Limit

control

230v

Water

pump

230v

Water

Heater

230v

50Hz

Mains

Supply

Th/Stat.

230v

Timed

Test

Earth

ANCILLARIES

Link Cont. 230v

to A

ANNL

Continuous.

Fuse

T3.15A

g/y

p/r

bk br

See note *

ybk v

p/r

or v

ON OFF

bbr

p/r gy

br br

r Sleeve

Issue 07

Wire Colour Code

blue ----b black -----bk red ----r

brown ---br violet ---v black/white ---bk/w

grey ----gy white ----w purple/red ---p/r

orange ---or yellow ----y green/yellow---g/y

Butt

Conn.

TTB

FROST

ANTI-HYPO.

S8 S7

Cont. Off

When

fitted

Timed

SAC

When

fitted

br br

Voltage Selector

Fuse

T500mA

24v 0v

24v Relay

Module

N/C N/O

Comm.

g/y

FAN

TX1

TX2

24V 0V

230v

Auto Transformer

6VA Double Bobbin

Note-: *

If Superjan fitted remove

red wire link between

terml. 10 & 12

Component InternalSize Resistance Component Internal Size Resistance

(mm) Factor (mm) Factor

FlueBlocks 197x67 0.85 per meter 135OBend 100mmpipe 0.61per

231x65 0.65 run 125mmpipe 0.25fitting

317 x 63 0.35 150 mm pipe 0.12

140x102 0.60 197x67 0.30

200 x 75 0.60 231 x 65 0.22

183x90 0.45 317x63 0.13

Pipe 100 0.78 Rakingblock Any 0.30perblock

125 0.25

150 0.12 Adaptor block Any 0.50

Chimney 213 x 213 0.02 Terminal 100 mm ridge 2.5

125 mm ridge 1.0

90OBend 100 mm pipe 1.22 per 150 mm ridge 0.48

125 mm pipe 0.50 fitting 100 mm GCI 0.6

150 mm pipe 0.24 125 mm GCI 0.25

150 mm GCI 0.12

Table 2

Resistance factors for use in calculating equivalent heights

Appliance Inlet Flue Outlet

Resistance (Ki) Resistance (Ko)

100 mm dia spigot 2.5 100 mm flue 2.5

125 mm dia spigot 1.0 125 mm flue 1.0

150 mm dia spigot 0.48 150 mm flue 0.48

Table 3

Inlet and outlet resistance

d. Worked Calculation Example:

A warm air unit with a 100 mm diameter flue spigot, fitted with a pre-fabricated flue system leading to a

ridge tile in the loft (refer Fig. 2):

Fromtable3:

Kia Inlet resistance of actual flue =2.5

Koa Outlet resistance of actual flue = 2.5

Kie Inlet resistance of equivalent flue = 2.5

Koe Outlet resistance of the actual flue = 2.5

Fromtable2:

Other resistances of actual flue:

Terminal =2.5

Pipe bend ( 2 x 0.61) = 1.22

Pipe (4 x 1m @ 0.78) = 3.12

(5 x 0.3m @ 0.78) =1.17

SumK = 8.01

Equivalent height :

Fromtheformula

(2.5 + 2.5)

He= 6.2 x

(2.5 + 2.5) - (0.78 x 6.2) + 8.01

He= 3.793 This flue exceeds 1.0m equivalent height and is therefore satisfactory.

e. Main burner lights i. Loose electrical connection Check connections.

but fan fails to run at fan control.

afterapprox.3 min.

ii. Fan delay control faulty. ReplaceFanDelay/Limit Switch.

iii. Faulty fan assembly. Replace, taking care not to damage

impeller.

iv. Burner pressure setting incorrect. Adjust pressure as necessary.

g. Main burner opera- i. Gas rate or burner pressure Check gas rate and burner pressure

ting with intermittent setting too low. setting.

fan operation.

ii. Fan delay control faulty ReplaceFan Delay/Limit control.

h. Noisy operation. i. Gas pressure too high. Check burner pressure setting.

ii. Noisy fan motor. Replace fan assembly.

iii. Fan speed setting too high. Adjust fan speed.

i. Fan runs for excessive i. Fan delay control faulty. Replace FanDelay/Limit control.

period or operates

intermittently after

main burner shuts down.

Fig.2

Worked example ofequivalentflueheight

5.1.12 Special consideration must be given to external flues with a view to prevention of condensation and weathering

problems.

5.1.13 An approved terminal should always be used; a ridge terminal or “GC1” terminal is specifically recommended.

The latter should be positioned in a free air space where it is not shielded by any structure. A minimum of 1m

(3ft.) from any vertical or inclined roof structure must be allowed for.

5.1.14 Where flue blocks are used, builders should ensure that no obstruction is created during erection. The installer

should ensure that the connection flue does not project beyond the internal wall of the flue blocks and that there

is provision for examination and servicing.

1.6m

4.6m

Ha= 6.2m

Ridge Terminal

2 x 300 mm lengths

4 x 1000 mm lengths

45Obend

2 x 300 mm lengths

300 mm length

Flue spigot

100 mm dia flue pipe

615

9. DEFECTDIAGNOSIS

9.1 IMPORTANT:Ifanelectricaldefectoccursafterinstallationoftheappliance;preliminaryearthcontinuity,

polarity, and resistance to earth checks should be carried out with a multimeter. On completion of any

maintenance/fault-finding task that has required the breaking and remaking of electrical connections, then

checks of continuity, polarity, and resistance to earth must be repeated.

9.2 WARNING: When purging or checking gas supplies, ensure that the ventilation to the room or cupboard is adequate, and

that all naked lights are extinguished.

SYMPTOM POSSIBLECAUSE REMEDY

a. Pilotwillnotlight. i. No gas supply to heater. Check for gas at inlet pressure test

point on Multifunctional Control.

ii. Gas supply pipe not purged. Purge gas supply pipe in accordance

with BS 6891.

iii Pilot orifice restricted. Clear pilot orifice or replace pilot injector.

iv. Piezo system faulty. Check igniter, lead, and electrode.

v. Excessive gas supply pressure. Check that mains gas pressure is 37mbar,

and reduce if necessary.

b. Pilot lights but goes i. Connection between thermo- Check connection is secure.

out on releasing START couple and Multifunctional

button during initial Control not secure.

light-up, or after

normal operation. ii. Faulty Multifunctional Replace Multifunctional Control.

Control.

iii. Faulty Thermocouple. Replace Thermocouple.

c. Main burner opera- i. Gas rate or burner pressure Check gas rate and burner pressure

ting intermittently setting high. setting.

with fan running. ii. Temperature rise excessive. Adjust fan speed or gas rate accordingly.

iii. Air filter or return air path Check filter is clean and air path is clear.

restricted.

iv. Excessive number of outlets Open additional outlets.

closed.

v. Spillage of flue gases. Carry out spillage test and rectify.

vi. Spillage monitor device (TTB) Replace Spillage device(TTB)

faulty.

d. Pilot alight but main i. Mains electrical supply not Check mains supply.

burner not igniting. connected to heater.

ii. Controls not demanding heat Check that time control and

room thermostat are operating correctly.

iii. T3.15Afusefailed. Replace. If failure occurs again, check

wiring for short circuits.

iv. Loose connection to room thermo- Check connections.

stat, Limit Switch, gas control lead,

time control, or transformer.

v. 230V/24V transformer failure. Check 24V side with test meter, if voltage

missing, replace transformer.

vi. Faulty relay module Check 230V at white wire from switch S5

vii. Multifunctional Control faulty. Replace Multifunctional Control.

viii.LimitSwitchfaulty. Short circuit control and replace Fan Delay/

Limit control if necessary.

ix. Room thermostat or external Fit temporary loop in heater thermostat

wiring faulty. socket. If heater ignites, external circuit

or room thermostat is faulty.

x. Spillage device faulty Check Spillage device and wiring for open

circuit.

8.10 TIMECONTROLand SWITCH REMOVAL:

8.10.1 Ensure that the electrical supply is isolated.

8.10.2 Remove the appliance louvre door, release the 2 x securing screws and hinge down the fan chamber door.

TimeControl removal:

8.10.3 Disconnect conductors ‘C1’, ‘C2’, ‘C3’ and ‘C5’ from the Time control.

8.10.4 Release the 2 x fixing screws, and withdraw the Time control.

8.10.5 Refitting or replacement is in reverse order.

8.10.6 Set the Time Control to the required ON and OFF times.

8.10.7 Set the Time Control to the correct time.

Switchremoval:

8.10.8 Disconnect the conductors from the switch terminals.

8.10.9 Depress the retaining clips and press the switch out of the fascia panel.

8.10.10 Refitting or replacement is in reverse order.

WARNING:Thefasciapanelisheldinplaceby push fit retainerswhichmustberemovedwithcautiontoavoid

causingdamagetothesupportpins.Removalof the fascia isnotadvisedunlessit is intended tobereplaced.

8.11 FAN DELAYCONTROL/LIMITSWITCHREMOVAL:

8.11.1 Ensure that the electrical supply is isolated.

8.11.2 Remove the appliance louvre door, release the 2 x securing screws and hinge down the fan chamber door.

8.11.3 Disconnect the following at the Electrical panel:

a. Limit Switch from connection block terminals ‘13’ and ‘14’,

b. Fan Delay Control from connection block terminals ‘18’ and ‘17’,

c. Earth connection from common earth stud.

8.11.4 Release 2 x 4mm screws securing Limit Switch mounting plate, and withdraw the control from the appliance by

drawing the conductors through the grommet in the fan chamber floor.

8.11.5 Refitting or replacement is in reverse order.

8.12 SPILLAGEMONITORINGDEVICE (TTB) REMOVAL:

8.12.1 Ensure that the electrical supply is isolated.

8.12.2 Remove the appliance louvre door, release the 2 x securing screws and hinge down the fan chamber door.

8.12.3 Disconnect the TTB from its conductors.

8.12.4 Release 2 x screws securing the TTB Bracket to the fan chamber floor, and withdraw TTB Bracket.

8.12.5 Refitting or replacement is in reverse order.

8.13 HEATEXCHANGERACCESS:

8.13.1 Ensure that the electrical supply is isolated.

8.13.2 Remove the appliance louvre door.

8.13.3 Remove the Burner and ControlsAssembly as detailed in sect 8.2.

8.13.4 Release the 4 screws securing the combustion chamber heat shield, and withdraw the heat shield.

8.13.5 Release the 4 screws securing the top access cover plate, and withdraw the cover plate and gasket

8.13.6 Release the 4 screws securing the heat exchanger top sealing plate, and withdraw the sealing plate and gasket.

8.13.7 Reassembly is in reverse order.

NOTE:When reassembling,ensurethatthegaskets aresoundly sealed,and fullyre-commissiontheheater.

5.1.15 Important: Before installing the appliance, carry out a visual check of the flue system as directed in the relevant

section of BS5440 Pt. 1, then check the flue performance as follows:-

a. Close all doors and windows in the room in which the appliance is to be installed.

b. Introduce some heat into the flue, using a blow torch or other means.

c. Carry out a flow visualisation check with a smoke pellet at the intended position for the appliance. Ensure

that there is discharge of smoke from the correct terminal only, and no spillage into the room.

Smoke coming out of other than the correct terminal only, or a down draught or ‘no flow’condition,

indicates that the flue has failed the test, and the appliance shall not be connected until the defect has been

found and rectified, and the test satisfactorily completed.

5.2 ELECTRICAL

5.2.1 Mains.

a. The heater is supplied with mains cable (PVC sheathed, heat resisting to 85oC), 3-core Brown-Blue-

Green/Yellow, 6A, 0.75mm2), connected to a terminal block and exiting through the heater at the right

hand top. The cable is suitable for a 230V 50Hz supply and shall be connected to the fixed wiring

using a double pole switched, fused spur, incorporating a protective earth link. The fuse fitted shall be

rated 5A to BS 1362 Connections shall be in accordance with the current edition of I.E.E Regulations BS

7671.

b. Fan Delay Controls and Limit Switch are not adjustable and are set as follows:

i. Fan Delay Control closes at 54OC± 4.5OC; opens at 40OC±3OC.

ii. Limit Switch opens at 80OC; closes at 60OC.

c. A 24V room thermostat (not supplied), that complies with BS 800 BS 3955 and BS 4201 is essential to

ensure close control of comfort conditions. An anticipator is located within the thermostat and is graded

in amps. The anticipator should be checked and adjusted to 0.2A.

5.2.2 RoomThermostatanditslocation.

a. The Room Thermostat should be located where there is free air circulation approx. 1.5m (5ft) from the

floor.

b. Avoid the following locations:-

i. In a room where temperature is greatly affected by the sun or any other heat source, e.g. radiant

fire, wall light fittings or TV set.

ii. Near an outside door or windows, or on an outside wall.

iii. Where affected by warm air ducts, diffusers, waste pipes or the heater itself.

iv. Where subject to vibration.

c. Connect Room thermostat wires to control panel terminals ‘7’ and ‘8’ (see Fig. 6 or 7).

5.3 GAS (See BS5864 and BS 6891)

5.3.1 An independent gas supply pipe from the meter is to be preferred wherever possible. When this is not possible,

the pipe must be capable of taking the complete input of the heater and all other gas appliances being served by

this same pipe. This supply should be suitably sized to conform to British Standards requirements of no more than

2.5 mbar (0.4in wg) pressure drop (See table of discharge in BS 5482 Part 1.).

5.3.2 The 1/2in union gas cock (supplied) must be fitted to the gas inlet of the heater for easy isolation during

servicing. The gas pipe should be so fitted and installed as to be durable, substantial and gas tight. To assist in

determining where a gas connection may not be tight, a leak detection fluid should be applied around the

connection. Under no circumstances should a flame be used to locate a gas leak. Gas entry to the air heater is

through either side to a Rc1/2 (1/2in BSP. external [taper] thread).

6. COMMISSIONING

6.1 PREPARATION:

6.1.1 Ensure that:

a. Gas and Electrical supplies are OFF.

b. Filter, fan and fan compartments are free from obstructions.

c. All registers or grilles are open and conform to design specifications.

d. Return, relief and ventilation air installations are adequate.

8.5 MULTIFUNCTIONALCONTROLREMOVAL:

8.5.1 Remove the Burner and ControlsAssembly as detailed in 8.2

8.5.2 Disconnect the Thermocouple at the Multifunctional Control, avoiding damage to the capillary.

8.5.3 Disconnect the Pilot Feed Pipe from the Multifunctional Control.

8.5.4 Disconnect the Multifunctional Control input and output supply feeds.

8.5.5 Refitting or replacement is in reverse order.

NOTE:When refitting or replacing the Multifunctional Control, the ‘O’ ring seal is to be replaced.

8.6 PIEZOUNITREMOVAL:

8.6.1 Disconnect the 2 conductors from Piezo unit.

8.6.2 Release the retaining nut and remove the Piezo unit from its mounting bracket.

8.6.3 Refitting or replacement is in reverse order.

8.7 AIRCIRCULATINGFAN,REMOVALANDCLEANING:

8.7.1 Ensure that the electrical supply is isolated.

8.7.2 Remove the appliance louvre door, release the 2 x securing screws and hinge down the fan chamber door.

8.7.3 Disconnect the fan flying leads from the FanAssembly.

8.7.4 Release the FanAssembly securing screw and withdraw the Fan Assembly from the Heater cabinet, avoiding

damage to the fan blades.

8.7.5 Remove all dust from both the impeller and motor, taking care to not disturb the balance of the fan.

8.7.6 Refitting or replacement is in reverse order.

8.8 ELECTRICALASSEMBLYREMOVAL:

8.8.1 Ensure that the electrical supply is isolated.

8.8.2 Remove the appliance louvre door, release the 2 x securing screws and hinge down the fan chamber door.

8.8.3 Disconnect the following:

a. Air circulation fan flying leads from the Fan assembly,

b. 230V mains ‘L’, ‘N’ and ‘E’from connection block terminals ‘1’ and ‘2’, and Earth stud respectively,

c. Room thermostat connections from connection block terminals ‘7’ and ‘8’,

d. Limit Switch from connection block terminals ‘13’ and ‘14’,

e. Fan Delay Control from connection block terminals ‘18’ and ‘17’,

f. Multifunctional Control from connection block terminals ‘16 (N) and ‘15’ (L),

g. Water heater from connection block terminals ‘10’ (L) and ‘9’ (N),

h. Water Pump from connection block terminals ‘12’ (L) and ‘11’ (N),

i. Cleanflow from connection block terminals ‘19’ (24V) and ‘20’ (0V),

j. Earth lead from the fan chamber floor,

8.8.4 Disconnect 2 x Spillage monitoring device connections from the terminal block on the fan compartment

diaphragm.

8.8.5 Release the 2 x hinge pins and withdraw the ElectricalAssembly, releasing wiring from cable clamps and

grommets as required..

8.8.6 Refitting or replacement is in reverse order.

8.9 TRANSFORMERREMOVAL:

8.9.1 Ensure that the electrical supply is isolated.

8.9.2 Remove the appliance louvre door, release the 2 x securing screws and hinge down the fan chamber door.

8.9.3 Disconnect the conductors from the large Transformer.

8.9.4 Release 2 x screws and nuts securing Transformer to Electrical assembly, and remove Transformer..

8.9.5 Refitting or replacement is in reverse order.

6.2 SYSTEMBALANCING:

6.2.1 Set theAir Heater electrical supply ON.

6.2.2 Set the SUMMERAIRFLOW switch to ‘1’.

6.2.3 Balance the system to provide the required volume proportions at the warm air outlets.

Note: If the system includes ceiling diffusers, the air through these should be NOT LESS THAN 1.5m/s (300ft/min), except

for very small rooms, (i.e. bathrooms etc.). Outlet faces may require partial blanking in order to achieve this.

6.2.4 Set the SUMMERAIRFLOW switch to ‘0’.

6.3 IGNITIONOFPILOTAND MAINBURNERS:

WARNING: If the pilot light is extinguished either intentionally or unintentionally, no attempt should be made to

relight the gas for a minimum of 3 minutes. Ensure that the electrical supply, Time Control and Selector switches are set to

‘OFF’.

6.3.1 Set the room thermostat to its lowest setting.

6.3.2 On the Multifunctional Control, remove the Inlet Pressure test point cover, and a fit pressure test gauge (refer fig.

4).

6.3.3 Turn the heater Gas supply ON, test for gas soundness and purge the whole gas pipe as described in BS 5482

Part1.

6.3.4 Referring to Fig .4, press and hold the OPERATING CONTROL, and whilst observing the Pilot Burner, repeatedly

press the Piezo igniter button until the Pilot Burner ignites.

6.3.5 After 20 seconds release the OPERATING CONTROLand let it spring out; ensure that the Pilot Burner remains

alight. If the Pilot Burner extinguishes, rotate the OPERATING CONTROLclockwise to the ‘z’position and

ensure that the OPERATING CONTROL is fully reset. Wait three minutes and repeat steps 6.2.4 and 6.2.5 until

the Pilot burner remains alight.

6.3.6 With the Pilot burner lit, depress the OPERATING CONTROLand turn it to the position indicated by the flame

symbol.

6.3.7 Ensure that the pilot flame envelops thermocouple tip (refer Fig. 3).

6.3.8 Set the Heater Electricity supplyON.

6.3.9 Set the Time control to the required Heating On periods.

6.3.10 Set the Selector switch to ‘TIMED’.

6.3.11 Set the room thermostat to MAXIMUM.

6.3.12 Ensure that the main burner has now ignited.

6.3.13 Test for gas leakage at the supply, Multifunctional control, Pilot and Main burners using proprietary detection

fluid, sealing any leaks found.

6.3.14 Allow heater to operate for a minimum of 15 minutes to ensure stability.

Fig.3

PILOTBURNERASSEMBLY

Thermocouple

Electrode

PilotBurner

6.4 MAINBURNER PRESSURETEST:

6.4.1 Referring to Table 4 ensure that the pressure test gauge indicates the correct burner pressure, a low pressure

indicates a regulator fault or low cylinder pressure.

6.5 EXTINGUISHINGOFBURNERS:

6.5.1 On the Multifunctional Control, rotate the OPERATING CONTROL clockwise to the ‘z’ position and ensure that

the OPERATING CONTROLfully resets, and both the Pilot and Main Burners are extinguished.

6.5.2 On the Multifunctional Control, remove the pressure test gauge and refit the Inlet Pressure test point cover, and

check for gas soundness.

6.6 TEMPERATURERISECHECKS:

6.6.1 Ignite the Pilot and Main Burners and allow 15 minutes for stability before continuing.

6.6.2 With the Main Burner operating continuously, check that the temperature rise across heater is between 45oC -

55oC, adjusting the fan speed at the control panel voltage selector, (decrease voltage selection to decrease fan

speed).

Note:Tapping1 = 210V,tapping2=175V,tapping 3 =150V,tapping 4 = 120Vandtapping5= 100V.

8.1.9 Using a torch or similar, introduce a light source into the heat exchanger burner aperture and upper access port,

and again examine the heat exchanger for signs of cracks or holes, particularly around welded joints, whilst again

viewing through the FanAperture.

8.1.10 Refit the Air Circulation fan, Burner and ControlsAssembly, and air filter/air cleaner.

8.1.11 Light the appliance and note the main burner flame profile. If the flame profile is affected when theAir

Circulation fan switches on, check for any air leaks between the air heater and the base plenum, paying particular

attention to heaters with rear draught diverters. Rectify any air leaks before continuing with this procedure.

8.1.12 Allow the air heater to operate for approximately 15 minutes to ensure stability, and with the main burner lit,

ensure that the operation ofAir Circulation fan does not affect the main burner flame profile.

8.2 BURNERANDCONTROLASSEMBLYREMOVAL:

8.2.1 Ensure that the Gas and Electrical supplies are switched OFF

8.2.2 Remove the appliance louvre door.

8.2.3 Disconnect the igniter at the Piezo unit.

8.2.4 Disconnect the Multifunctional Control electrical connections.

8.2.5 Disconnect the gas supply by breaking the union at the input side of the Multifunctional Control, and water

heater union (if applicable).

8.2.6 Whilst supporting the Burner and ControlAssembly, remove 3 x BurnerAssembly fixing screws and withdraw the

Burner and ControlAssembly

8.2.7 Refit the Burner and ControlAssembly in reverse order.

8.3 BURNERANDCONTROLASSEMBLYCLEANING:

8.3.1 Remove the Burner and ControlsAssembly as detailed in 8.2.

8.3.2 Disconnect the Pilot Feed Pipe and Thermocouple from the Multifunctional Control.

8.3.3 Release the single screw, nut and washer securing the PilotAssembly to the Burner and Controls Assembly, and

remove the PilotAssembly.

8.3.4 Release the 2 screws, nuts and washers securing the Main Burner to the mounting bracket, and remove the Main

Burner.

8.3.5 Clean burner thoroughly both insideand out with a soft brush. DO NOT ENLARGE, DISTORT OR DAMAGE

BURNERHOLES.

8.3.6 Reassemble in reverse order.

8.4 PILOTBURNER,THERMOCOUPLEANDELECTRODE, REMOVALAND REPLACEMENT:

8.4.1 Remove the Burner and Controls Assembly as detailed in 8.2

8.4.2 Disconnect the Igniter lead from the Electrode.

8.4.3 Disconnect the Thermocouple from the Multifunctional Control, taking care to avoid damage to the thermocouple

capillary.

8.4.4 Release the Pilot Feed Pipe from the Multifunctional Control.

8.4.5 Release the single screw, nut and washer securing the PilotAssembly to the Burner and Controls Assembly, and

remove the PilotAssembly.

8.4.6 Release the Thermocouple securing nut from the Pilot BurnerAssembly and withdraw the Thermocouple, taking

care to avoid damage to the Thermocouple capillary.

8.4.7 Release the Electrode securing nut from the Pilot BurnerAssembly and withdraw the Electrode.

8.4.8 Release the Pilot Feed Pipe securing nut from the Pilot Burner Assembly and withdraw the Pilot Feed Pipe and

Pilot Injector from the Pilot Burner assembly, and disconnect the Pilot Injector from Pilot Feed Pipe hook.

8.4.9 Release the 2 screws securing the Pilot Burner Bracket to the Pilot Mounting bracket, and remove the Pilot

Burner Bracket.

8.4.10 Refitting or replacement is in reverse order.

NOTE: When refitting orreplacing the Thermocouple, tighten only to FINGER TIGHT+ 1 FLAT.

1. Operating control

2. Inlet Pressure test point

3. Outlet Pressure test point

4. Burner Pressure adjuster

Fig. 4

MULTIFUNCTIONALCONTROL

6.7 AUTOMATICCONTROLSCHECK

6.7.1 SettheTIME CONTROL to‘ON’.

6.7.2 Set the room thermostat slowly clockwise until the Main Burner ignites.

6.7.3 Ensure that the fan starts to operate after a short period (approx. 1-2 minutes).

6.7.4 When the temperature reaches the control setting, ensure that the Main Burner extinguishes followed by the fan

switching off after a short period.

6.7.5 When the temperature falls below the control setting, ensure that the Main Burner re-ignites followed by fan

operation.

6.4 MAINBURNER PRESSURETESTANDTEMPERATURERISECHECK:

6.4.1 Referring to Table 4 and Fig. 4 below, ensure that the pressure test gauge indicates correct pressure, adjusting the

supply pressure if required.

a. AttheMultifunctionalcontrol:

i. Remove the Burner PressureAdjuster cover.

ii. Set the Burner Pressure Adjuster to provide a pressure test gauge indication for the correct burner

pressure as detailed in Table 4.

iii. Refit the Burner Pressure Adjuster cover.

6.4.2 Check that the temperature rise across heater is between 45oC - 55oC, setting the fan speed accordingly by alteration

of the voltage selection at the tap changer on the control panel, (decrease voltage to decrease fan speed thus

increase temperature).

Note: Tapping 1 = 150V,Tapping 2 =170V,Tapping3=190V,Tapping 4 =210vandTapping5=230V.

.5 EXTINGUISHINGOFPILOTAND MAINBURNERS:

6.5.1 On the Multifunctional Control, rotate the OPERATING CONTROL clockwise to the ‘O’ position and ensure that

the OPERATING CONTROL fully resets, and both Pilot and Main Burners are extinguished.

6.5.2 On the Multifunctional Control, remove the pressure test gauge and secure the Pressure test point screw.

6.6 AUTOMATICCONTROLS CHECK

6.6.1 Ignite the Pilot burner.

6.6.2 SettheTIMECONTROL to ‘ON’.

6.6.3 Set the Room Thermostat slowly clockwise until the Main Burner ignites.

6.6.4 Ensure that the fan starts to operate after a short period.

6.6.5 When the temperature reaches the control setting, check that the Main Burner extinguishes followed by the fan

switching off after a short period.

6.6.6 When the temperature falls below the control setting, ensure that the Main Burner re-ignites followed by fan

operation. 9

6.8 SAFETYCHECKS:

6.8.1 Check for gas soundness within the appliance.

6.8.2 Spillage test: Carry out a full spillage test as follows, and ensure that the flue operates effectively with all doors

closed and any extractor fans in operation.

NOTE:If an extractor fan is situated in an adjoining or adjacent room, carry out the spillage test with the interconnecting

doors open.

Ifthedraughtdiverter is accessible:

a. Introduce smoke into the draught diverter adjacent to an exit from the heat exchanger, by means of a

smoke match or puffer.

b. Ensure that there is no spillage present (indicated by displacement of smoke downwards and out of the

draught diverter.

IftheDraught Diverter isnot accessible:

a. Introduce smoke, by means of part of a smoke pellet on a non-combustible support, into the heat

exchanger.

b. Extinguish the Main and Pilot burners.

c. Ensure that there is no spillage evident by visually observing the draught diverter location on the air

heater.

d. If spillage is evident, further investigation and rectification is required before re-testing the appliance.

e. Repeatspillagetestsbutwiththefan running, orSummerAirflowswitchsettoON.

WARNING:Theapplianceshallnotbe leftconnected to thegas supply unlessit hassuccessfully passed

theabovespillagetest.

6.8.3 Turn OFF the gas supply at the service cock and ensure that the Multifunctional Control fail-safe operates within

60 secs (indicated by loud click from Multifunctional Control).

6.8.4 Turn gas supply ON at service cock.

6.8.5 Switch the appliance electrical supply OFF.

6.8.6 Disconnect theAir Circulation Fan at the flying lead socket.

6.8.7 Switch the appliance electrical supply ON.

6.8.8 Ignite the Pilot and Main Burners as detailed in 6.3.1 to 6.3.5.

6.8.9 Ensure that the Limit Switch operates, indicated by the main burner extinguishing, within 120 and 180 seconds.

6.8.10 Switch the appliance electrical supply OFF.

6.8.11 Reconnect theAir Circulation Fan.

6.8.12 Switch the appliance electrical supply ON.

6.8.13 Ensure that the Main Burner re-ignites when the appliance temperature reduces, (note: with theAir Circulation Fan

disconnected, there may be some delay before the Main Burner re-ignites).

kW MJ/h Btu/h

INPUT 11.1 40.0 38,000

OUTPUT 8.30 29.88 28,320

Gas rate 0.418m3/h

PropaneG31 (14.77ft3/h)

Burner setting 33mbar(13.2inwg)

pressure (hot)

Main Injector Bray1.78mm

Table4

Main Burner Pressure Settings

Table 5

FanPerformanceCurve

7. INSTRUCTIONS FOR USERS

7.1 If the building is unoccupied, ensure that the Instructions for User are left taped to the air heater for the User, and

Installation Instructions are left at or near the air heater for use on future service calls.

7.2 If the building is occupied, hand the User Instructions over and ensure the User understands:

7.2.1 How to ignite the pilot and burner.

7.2.2 How to operate the room thermostat, time and heater ON/OFF switch and summer air circulation switch, and that the

time control must be reset following a power failure.

7.2.3 How to extinguish the pilot and main burner at the Multifunctional control, and switch off electrical supply to the

heater.

7.2.4 How to remove, clean and refit the air filter and at what intervals (i.e. fortnightly, or for new houses, weekly).

7.2.5 How to control the heating system by opening and closing warm air outlets.

7.2.6 How to obtain summer air circulation.

7.2.7 That the air grilles on the heater or heater compartment; grilles and ventilators in the walls, windows or doors of the

building must not be obstructed.

7.2.8 That the heater must be serviced at least once a year by a competent person to ensure efficient and safe operation.

7.2.9 That the red instructions for safe use have been pointed out and understood.

7.2.10 That expert help must be obtained if persistent failure of the pilot burner occurs.

8. MAINTENANCE

IMPORTANT: Ensuregasandelectricitysuppliesareisolatedbeforecommencinganymaintenanceorreplacementofcompo-

nents.Aftercompletionofanymaintenance,alwaystestforgassoundnessandcarryoutacompletefunctionaltestoftheappli-

anceinaccordance withCommissioning Instructionsat Sect6.1 to6.8 inclusive.

8.1 ROUTINEMAINTENANCE:

8.1.1 Operate the appliance and check for the correct function of the burner and controls.

8.1.2 Turn OFF the gas and electrical supplies to the appliance.

8.1.3 Remove the air heater front panel.

8.1.4 Remove and check the return air filter/cleaner for cleanliness, remove and clean theAir Circulation fan as

detailed in para 8.7.

8.1.5 Remove the Burner and ControlsAssembly as detailed in para 8.2. Inspect and clean the main burner and injector

as necessary. Examine the main burner for cracks, including hairline cracks, exchanging the burner as necessary.

8.1.6 Inspect and clear the pilot burner orifice.

8.1.7 Clean the heat exchanger flueways by thoroughly brushing from above and below.

8.1.8 By viewing through the FanAperture, and using a torch or similar, examine the heat exchanger externally for signs

of cracks or holes, particularly around welded joints.

200 250 300 350 400 ft3/min

0.09 0.12 0.14 0.17 0.19 m3/sec

AIR VOLUME

mbar in.wg.

0.50 0.20

0.375 0.15

0.25 0.10

0.125 0.05

RESISTANCEEXTERNALTOHEATER

100V

120V

150V

175V

210V

6.8 SAFETYCHECKS:

6.8.1 Check for gas soundness within the appliance.

6.8.2 Spillage test: Carry out a full spillage test as follows, and ensure that the flue operates effectively with all doors

closed and any extractor fans in operation.

NOTE:If an extractor fan is situated in an adjoining or adjacent room, carry out the spillage test with the interconnecting

doors open.

Ifthedraughtdiverter is accessible:

a. Introduce smoke into the draught diverter adjacent to an exit from the heat exchanger, by means of a

smoke match or puffer.

b. Ensure that there is no spillage present (indicated by displacement of smoke downwards and out of the

draught diverter.

IftheDraught Diverter isnot accessible:

a. Introduce smoke, by means of part of a smoke pellet on a non-combustible support, into the heat

exchanger.

b. Extinguish the Main and Pilot burners.

c. Ensure that there is no spillage evident by visually observing the draught diverter location on the air

heater.

d. If spillage is evident, further investigation and rectification is required before re-testing the appliance.

e. Repeatspillagetestsbutwiththefan running, orSummerAirflowswitchsettoON.

WARNING:Theapplianceshallnotbe leftconnected to thegas supply unlessit hassuccessfully passed

theabovespillagetest.

6.8.3 Turn OFF the gas supply at the service cock and ensure that the Multifunctional Control fail-safe operates within

60 secs (indicated by loud click from Multifunctional Control).

6.8.4 Turn gas supply ON at service cock.

6.8.5 Switch the appliance electrical supply OFF.

6.8.6 Disconnect theAir Circulation Fan at the flying lead socket.

6.8.7 Switch the appliance electrical supply ON.

6.8.8 Ignite the Pilot and Main Burners as detailed in 6.3.1 to 6.3.5.

6.8.9 Ensure that the Limit Switch operates, indicated by the main burner extinguishing, within 120 and 180 seconds.

6.8.10 Switch the appliance electrical supply OFF.

6.8.11 Reconnect theAir Circulation Fan.

6.8.12 Switch the appliance electrical supply ON.

6.8.13 Ensure that the Main Burner re-ignites when the appliance temperature reduces, (note: with theAir Circulation Fan

disconnected, there may be some delay before the Main Burner re-ignites).

kW MJ/h Btu/h

INPUT 11.1 40.0 38,000

OUTPUT 8.30 29.88 28,320

Gas rate 0.418m3/h

PropaneG31 (14.77ft3/h)

Burner setting 33mbar(13.2inwg)

pressure (hot)

Main Injector Bray1.78mm

Table4

Main Burner Pressure Settings

Table 5

FanPerformanceCurve

7. INSTRUCTIONS FOR USERS

7.1 If the building is unoccupied, ensure that the Instructions for User are left taped to the air heater for the User, and

Installation Instructions are left at or near the air heater for use on future service calls.

7.2 If the building is occupied, hand the User Instructions over and ensure the User understands:

7.2.1 How to ignite the pilot and burner.

7.2.2 How to operate the room thermostat, time and heater ON/OFF switch and summer air circulation switch, and that the

time control must be reset following a power failure.

7.2.3 How to extinguish the pilot and main burner at the Multifunctional control, and switch off electrical supply to the

heater.

7.2.4 How to remove, clean and refit the air filter and at what intervals (i.e. fortnightly, or for new houses, weekly).

7.2.5 How to control the heating system by opening and closing warm air outlets.

7.2.6 How to obtain summer air circulation.

7.2.7 That the air grilles on the heater or heater compartment; grilles and ventilators in the walls, windows or doors of the

building must not be obstructed.

7.2.8 That the heater must be serviced at least once a year by a competent person to ensure efficient and safe operation.

7.2.9 That the red instructions for safe use have been pointed out and understood.

7.2.10 That expert help must be obtained if persistent failure of the pilot burner occurs.

8. MAINTENANCE

IMPORTANT: Ensuregasandelectricitysuppliesareisolatedbeforecommencinganymaintenanceorreplacementofcompo-

nents.Aftercompletionofanymaintenance,alwaystestforgassoundnessandcarryoutacompletefunctionaltestoftheappli-

anceinaccordance withCommissioning Instructionsat Sect6.1 to6.8 inclusive.

8.1 ROUTINEMAINTENANCE:

8.1.1 Operate the appliance and check for the correct function of the burner and controls.

8.1.2 Turn OFF the gas and electrical supplies to the appliance.

8.1.3 Remove the air heater front panel.

8.1.4 Remove and check the return air filter/cleaner for cleanliness, remove and clean theAir Circulation fan as

detailed in para 8.7.

8.1.5 Remove the Burner and ControlsAssembly as detailed in para 8.2. Inspect and clean the main burner and injector

as necessary. Examine the main burner for cracks, including hairline cracks, exchanging the burner as necessary.

8.1.6 Inspect and clear the pilot burner orifice.

8.1.7 Clean the heat exchanger flueways by thoroughly brushing from above and below.

8.1.8 By viewing through the FanAperture, and using a torch or similar, examine the heat exchanger externally for signs

of cracks or holes, particularly around welded joints.

200 250 300 350 400 ft3/min

0.09 0.12 0.14 0.17 0.19 m3/sec

AIR VOLUME

mbar in.wg.

0.50 0.20

0.375 0.15

0.25 0.10

0.125 0.05

RESISTANCEEXTERNALTOHEATER

100V

120V

150V

175V

210V

6.4 MAINBURNER PRESSURETEST:

6.4.1 Referring to Table 4 ensure that the pressure test gauge indicates the correct burner pressure, a low pressure

indicates a regulator fault or low cylinder pressure.

6.5 EXTINGUISHINGOFBURNERS:

6.5.1 On the Multifunctional Control, rotate the OPERATING CONTROL clockwise to the ‘z’ position and ensure that

the OPERATING CONTROLfully resets, and both the Pilot and Main Burners are extinguished.

6.5.2 On the Multifunctional Control, remove the pressure test gauge and refit the Inlet Pressure test point cover, and

check for gas soundness.

6.6 TEMPERATURERISECHECKS:

6.6.1 Ignite the Pilot and Main Burners and allow 15 minutes for stability before continuing.

6.6.2 With the Main Burner operating continuously, check that the temperature rise across heater is between 45oC -

55oC, adjusting the fan speed at the control panel voltage selector, (decrease voltage selection to decrease fan

speed).

Note:Tapping1 = 210V,tapping2=175V,tapping 3 =150V,tapping 4 = 120Vandtapping5= 100V.

8.1.9 Using a torch or similar, introduce a light source into the heat exchanger burner aperture and upper access port,

and again examine the heat exchanger for signs of cracks or holes, particularly around welded joints, whilst again

viewing through the FanAperture.

8.1.10 Refit the Air Circulation fan, Burner and ControlsAssembly, and air filter/air cleaner.

8.1.11 Light the appliance and note the main burner flame profile. If the flame profile is affected when theAir

Circulation fan switches on, check for any air leaks between the air heater and the base plenum, paying particular

attention to heaters with rear draught diverters. Rectify any air leaks before continuing with this procedure.

8.1.12 Allow the air heater to operate for approximately 15 minutes to ensure stability, and with the main burner lit,

ensure that the operation ofAir Circulation fan does not affect the main burner flame profile.

8.2 BURNERANDCONTROLASSEMBLYREMOVAL:

8.2.1 Ensure that the Gas and Electrical supplies are switched OFF

8.2.2 Remove the appliance louvre door.

8.2.3 Disconnect the igniter at the Piezo unit.

8.2.4 Disconnect the Multifunctional Control electrical connections.

8.2.5 Disconnect the gas supply by breaking the union at the input side of the Multifunctional Control, and water

heater union (if applicable).

8.2.6 Whilst supporting the Burner and ControlAssembly, remove 3 x BurnerAssembly fixing screws and withdraw the

Burner and ControlAssembly

8.2.7 Refit the Burner and ControlAssembly in reverse order.

8.3 BURNERANDCONTROLASSEMBLYCLEANING:

8.3.1 Remove the Burner and ControlsAssembly as detailed in 8.2.

8.3.2 Disconnect the Pilot Feed Pipe and Thermocouple from the Multifunctional Control.

8.3.3 Release the single screw, nut and washer securing the PilotAssembly to the Burner and Controls Assembly, and

remove the PilotAssembly.

8.3.4 Release the 2 screws, nuts and washers securing the Main Burner to the mounting bracket, and remove the Main

Burner.

8.3.5 Clean burner thoroughly both insideand out with a soft brush. DO NOT ENLARGE, DISTORT OR DAMAGE

BURNERHOLES.

8.3.6 Reassemble in reverse order.

8.4 PILOTBURNER,THERMOCOUPLEANDELECTRODE, REMOVALAND REPLACEMENT:

8.4.1 Remove the Burner and Controls Assembly as detailed in 8.2

8.4.2 Disconnect the Igniter lead from the Electrode.

8.4.3 Disconnect the Thermocouple from the Multifunctional Control, taking care to avoid damage to the thermocouple

capillary.

8.4.4 Release the Pilot Feed Pipe from the Multifunctional Control.

8.4.5 Release the single screw, nut and washer securing the PilotAssembly to the Burner and Controls Assembly, and

remove the PilotAssembly.

8.4.6 Release the Thermocouple securing nut from the Pilot BurnerAssembly and withdraw the Thermocouple, taking

care to avoid damage to the Thermocouple capillary.

8.4.7 Release the Electrode securing nut from the Pilot BurnerAssembly and withdraw the Electrode.

8.4.8 Release the Pilot Feed Pipe securing nut from the Pilot Burner Assembly and withdraw the Pilot Feed Pipe and

Pilot Injector from the Pilot Burner assembly, and disconnect the Pilot Injector from Pilot Feed Pipe hook.

8.4.9 Release the 2 screws securing the Pilot Burner Bracket to the Pilot Mounting bracket, and remove the Pilot

Burner Bracket.

8.4.10 Refitting or replacement is in reverse order.

NOTE: When refitting orreplacing the Thermocouple, tighten only to FINGER TIGHT+ 1 FLAT.

1. Operating control

2. Inlet Pressure test point

3. Outlet Pressure test point

4. Burner Pressure adjuster

Fig. 4

MULTIFUNCTIONALCONTROL

6.7 AUTOMATICCONTROLSCHECK

6.7.1 SettheTIME CONTROL to‘ON’.

6.7.2 Set the room thermostat slowly clockwise until the Main Burner ignites.

6.7.3 Ensure that the fan starts to operate after a short period (approx. 1-2 minutes).

6.7.4 When the temperature reaches the control setting, ensure that the Main Burner extinguishes followed by the fan

switching off after a short period.

6.7.5 When the temperature falls below the control setting, ensure that the Main Burner re-ignites followed by fan

operation.

6.4 MAINBURNER PRESSURETESTANDTEMPERATURERISECHECK:

6.4.1 Referring to Table 4 and Fig. 4 below, ensure that the pressure test gauge indicates correct pressure, adjusting the

supply pressure if required.

a. AttheMultifunctionalcontrol:

i. Remove the Burner PressureAdjuster cover.

ii. Set the Burner Pressure Adjuster to provide a pressure test gauge indication for the correct burner

pressure as detailed in Table 4.

iii. Refit the Burner Pressure Adjuster cover.

6.4.2 Check that the temperature rise across heater is between 45oC - 55oC, setting the fan speed accordingly by alteration

of the voltage selection at the tap changer on the control panel, (decrease voltage to decrease fan speed thus

increase temperature).

Note: Tapping 1 = 150V,Tapping 2 =170V,Tapping3=190V,Tapping 4 =210vandTapping5=230V.

.5 EXTINGUISHINGOFPILOTAND MAINBURNERS:

6.5.1 On the Multifunctional Control, rotate the OPERATING CONTROL clockwise to the ‘O’ position and ensure that

the OPERATING CONTROL fully resets, and both Pilot and Main Burners are extinguished.

6.5.2 On the Multifunctional Control, remove the pressure test gauge and secure the Pressure test point screw.

6.6 AUTOMATICCONTROLS CHECK

6.6.1 Ignite the Pilot burner.

6.6.2 SettheTIMECONTROL to ‘ON’.

6.6.3 Set the Room Thermostat slowly clockwise until the Main Burner ignites.

6.6.4 Ensure that the fan starts to operate after a short period.

6.6.5 When the temperature reaches the control setting, check that the Main Burner extinguishes followed by the fan

switching off after a short period.

6.6.6 When the temperature falls below the control setting, ensure that the Main Burner re-ignites followed by fan

operation. 9