Johnson Controls E-Link User manual

E-Link Gateway Installation Instructions 1
Applications
The E-Link Gateway provides Johnson Controls® and
YORK® mechanical equipment, such as chillers and
rooftop units, with Building Automation System (BAS)
networking connectivity. It is designed with three active
serial ports: Port 1 and Port 4 are used for BAS
networking, Port 2 is reserved for connecting to the
equipment, and Port 3 provides access for auxiliary
monitoring and control.
To simplify the installation and setup, the E-Link
Gateway comes pre-configured with a series of chiller
and rooftop equipment profiles that you can choose by
selecting the correct DIP switch settings.
Several E-Link Gateway models are available for
connection to various types of input voltage and
equipment. For chillers using the OptiView™ or
Latitude Micro Panel, the E-Link Gateway consists of a
single circuit board attached to four studs inside the
Micro Panel, using the accessory mounting kit. The
panel supplies 12 VDC input power, eliminating the
need for an external power supply.
For chillers using the IPU-II based Micro Panel, the
E-Link Gateway is installed inside the Micro Panel and
requires an additional transformer to supply power to
the E-Link Gateway. The transformer is included in the
E-Link IPU-II Installation Kit. (This kit is not available in
Europe. Use E-Link Gateway YK-ELNKE00-0.)
For other types of chillers, the E-Link Gateway is
packaged in its own enclosure. In addition to the E-Link
Gateway circuit board, a transformer is included inside
the enclosure that converts a 120- or 240-volt input to
24 VAC power.
North American Emissions Compliance
United States
Canada
Installation
The E-Link Gateway is supplied as a circuit board that
can be installed directly into the equipment’s enclosure,
or can be supplied pre-mounted in an enclosure ready
for line voltage. Accessory mounting kits are used to
mount the E-link Gateway directly into OptiView
Latitude, and IPU-II based Micro Panels.
This equipment has been tested and found to
comply with the limits for a Class A digital device
pursuant to Part 15 of the FCC Rules. These limits
are designed to provide reasonable protection
against harmful interference when this equipment is
operated in a commercial environment. This
equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in
accordance with the instruction manual, may cause
harmful interference to radio communications.
Operation of this equipment in a residential area is
likely to cause harmful interference, in which case
the user will be required to correct the interference
at his/her own expense.
This Class (A) digital apparatus meets all the
requirements of the Canadian Interference-Causing
Equipment Regulations.
Cet appareil numérique de la Classe (A) respecte
toutes les exigences du Règlement sur le matériel
brouilleur du Canada.
IMPORTANT: Do not install the E-Link Gateway
directly into an equipment’s enclosure without the
use of an approved installation kit.
E-Link Gateway
Installation Instructions Part No. 24-10404-9, Rev. D
Issued November 2, 2011
Supersedes April 29, 2011

E-Link Gateway Installation Instructions2
IMPORTANT: The E-Link Gateway is intended to
provide an input to equipment under normal
operating conditions. Use this E-Link Gateway only
as an operating control. Where failure or malfunction
of the E-Link Gateway could lead to personal injury
or property damage to the controlled equipment or
other property, additional precautions must be
designed into the control system. Incorporate and
maintain other devices, such as supervisory or
alarm systems or safety or limit controls, intended to
warn of or protect against failure or malfunction of
the E-Link Gateway.
Table 1: YORK Chiller Models (Current
Production)
Board
Number1Language
(Native) Chiller Model
031-02550 BACnet®,
Modbus®,
YORK Talk 2,
4,800 bits per
second (bps)
YCWL, YCUL, YCAL,
YLAA, YCRL, YLPA
031-01095 YORK Talk 2,
4,800 bps YCAS, YCWS, YCRS
031-02478 YORK Talk 2,
4,800 bps YCAV, YCIV, YVAA
031-01065 YORK Talk 2,
1,200 bps YIA, YPC, YG, YB
031-01730 YORK Talk 3 YN, OM RETROFITS,
CR
031-02430 YORK Talk 3 YK, YT, YS, YR, YST,
YD, YMC2
331-02496 BACnet® YPAL
YORK-003 Modbus RTU YEWS-D1, YEAS,
YGAS2
1. Installing technician must verify board number in unit
prior to installation.
2. Software edition of YEWS-D1 (RHSYEWSD1) V1.08 or
later), YEAS (RHMASB V1.06 or later), YGAS
(RHMYGAS V1.03 or later) are supported.
Table 2: E-Link Gateway Product Code Numbers
Description Product Code
Numbers
E-Link with Serial Outputs (BACnet
Master-Slave/Token-Passing [MS/TP],
Modbus Remote Terminal Unit [RTU],
and N2)
YK-ELNK100-0
E-Link with LONWORKS® as an Output YK-ELNK101-0
E-Link with Serial Outputs in
Enclosure YK-ELNKE00-0
E-Link with LONWORKS Output in
Enclosure YK-ELNKE01-0
E-Link OptiView/Latitude Panel
Installation Kit YK-ELNKOLK-0
E-Link IPU-II Panel Installation Kit
(not available in Europe) YK-ELNKSTK-0

E-Link Gateway Installation Instructions 3
Mounting
OptiView Panel Installation
1. Attach the E-Link Gateway board to the studs
provided inside the chiller enclosure (Figure 1 or
Figure 2), using the four screws and washers
provided in the OptiView/Latitude installation kit.
2. Connect the communications cable (included with
the kit) from Port 2B on the E-Link Gateway to J2
on the OptiView Micro Panel. Ensure that wires are
connected according to Table 3.
3. Check for stray wire strands, which could cause
short circuits, and ensure all components are
secure.
4. Connect the BAS network to Port 1 (if the protocols
are transported by RS-485) or Port 4 (if the BAS
network is LONWORKS).
Note: For RS-485 2-wire operation, connect a 100
ohm 1 W resistor between COM and the E-Link
Gateway’s TB5 COM (see Figure 24).
5. Ensure jumper JP27 is set for RS-232 (see
Figure 20).
6. Connect the power harness (included with the kit)
from J2 on the E-Link Gateway to J21 on the
Optiview Micro Panel (see Figure 20).
The E-Link Gateway is now ready to be configured
using Quick Start; see the Commissioning a Standard
Application section in this document.
!
WARNING: Risk of Electric Shock.
Disconnect or isolate all power supplies
before making electrical connections.
More than one disconnect or isolation
may be required to completely de-
energize equipment. Contact with
components carrying hazardous voltage
can cause electric shock and may result
in severe personal injury or death.
Table 3: OptiView Wiring - E-Link Port 2B
E-Link Port 2B OptiView Port Wire Color
RX GTX Black
TX GRX Red
REF N/A Shield/Drain
Table 4: BAS Wiring - E-Link Port 1
E-Link Port 1 BAS Wire Color
++White
--Blue
REF REF Black
FIG:Opti_Pnl
Figure 1: OptiView Micro Panel Connected to
E-Link Gateway
FIG:Opti_Pnl1
Figure 2: OptiView Micro Panel for YMC2
Connected to E-Link Gateway

E-Link Gateway Installation Instructions4
IPU-II Panel Installation
(Installation Kit Not Available in Europe)
1. Attach the E-Link Gateway board to the panel in
the upper right side of the enclosure using the four
expansion screws and nuts provided in the IPU-II
Panel Installation Kit (see Figure 3).
2. Attach the 24 VAC transformer to the panel to the
left of the E-Link board using two screws (see
Figure 3).
3. Connect the communications cable (included with
the kit) between the E-Link board and IPU-II Micro
board.
4. Connect the transformer to the terminal block.
5. Connect the transformer to E-Link. Secure the
wiring with tie-wraps.
6. Connect the resistor if the RS-485 2-wire operation
is required.
7. Connect the communications cable shielded
ground to the ground screw.
The E-Link Gateway is now ready to be configured
using Quick Start; see the Commissioning a Standard
Application section in this document.
Micro Boar
d
24 VAC
Transforme
r
Expansion
Nut
Expansion
Nut
Screw
Sheet
Metal
Screw
Resisto
r
Secondar
y
Powe
r
Wiring
Harness Tie
Wrap
T
B5
TB 2
E-LIN
K
Transforme
r
Secondar
y
Ground
Communication
Wiring Harness
Com
Ground
T B1
T B 5
The Resistor is used for BAS
RS485 2 Wire Connection.
Connect one end of the
Resistor to the COM o
f
TB5 (24 VAC) and the othe
r
to Port 1 COM.
Use this resistor only if the
BAS wiring utilizes a 2 Wire
communication trunk
Communication Wiring Harness:
Connect to Micro Board
TB1 as Follows:
Wire Color / Terminal
Red / +
Black / -
+
-
REFSHLD
TB 1 RS485
F
I
G
:
I
P
U
p
n
l
i
n
s
t
Terminal block location
for YCAL-D, YCAL-E, and YLAA.
Terminal block location
for YCAL-C, YCWL, and
Primary Powe
r
Wiring Harness
TB2
TB5
Y
CUL-C.
Figure 3: IPU-II Panel Installation (Installation Kit Not Available in Europe)

E-Link Gateway Installation Instructions 5
Other Chiller Panel Installation
For all other applications, the E-Link Gateway includes
an optional enclosure. The optional enclosure does not
include communication cables due to the variety of
types and lengths that may be required.
The E-Link Gateway can be mounted as a stand-alone
enclosure either on the outside surface of the chiller
Micro Panel (close coupled), or on a smooth surface
within close proximity of the chiller panel enclosure.
For mounting on a Micro Panel, the line voltage power
is supplied by a power source in the Micro Panel.
Mounting on a Micro Panel
To mount the E-Link Gateway on a Micro Panel:
1. Disconnect power to the chiller Micro Panel.
2. Make sure the E-link Gateway enclosure fits
properly and that no obstructions, such as internal
boards, switches, or external conduit, prevent
mounting or servicing of the panel. See Figure 4 for
examples of good mounting locations.
3. Locate and remove the two plastic caps in the
bottom of the E-Link Gateway enclosure.
4. Mark an appropriate place on the enclosure for a
matching set of knock out holes. Mark and drill, or
punch, two holes in the Micro Panel.
5. Using two bulkhead pipe couplers, attach the
E-Link Gateway enclosure to the Micro Panel.
6. Complete wiring as described in the Applying
Power section in this document.
Note: Use of bulkhead pipe couplers provides
sufficient clearance to allow removal of the E-Link
Gateway cover.
IMPORTANT: Never install the E-Link Gateway
outside the confines of a building unless within
another enclosure rated IP 65/NEMA 4x or higher.
IMPORTANT: Make sure that the cover is securely
fastened to the enclosure and the internal ground
wire is attached before placing the Gateway in
operation. These steps help to minimize Radio
Frequency Interference (RFI) from being generated
and picked up.
!
WARNING: Risk of Electric Shock.
Disconnect or isolate all power supplies
before making electrical connections.
More than one disconnect or isolation
may be required to completely
de-energize equipment. Contact with
components carrying hazardous voltage
can cause electric shock and may result
in severe personal injury or death.
IMPORTANT: When attaching the E-Link Gateway
to a Micro Panel, ensure the E-Link Gateway does
not impede access to other components.
IMPORTANT: Be careful not to damage the E-link
Gateway or Micro Panel’s circuit boards during the
installation. Protect all circuit boards from metal
chips, which may cause short circuits if left on the
boards at startup.
E-LINK
Enclosure
YORK Chiller
Micro Panel
Alternative
Mounting
Locations
FIG:MntEquip
Figure 4: Mounting on the Equipment

E-Link Gateway Installation Instructions6
Wall Mounting
To mount the E-Link Gateway on a wall:
1. Check for proper clearances for the necessary
electrical and communications cable runs.
2. Ensure that power and communications wiring is in
compliance with all local, national, and regional
codes, and customer requirements.
3. Select a suitable location and mark the anchor
points. Ensure that the enclosure is level. See
Figure 5 for an example.
4. Drill the appropriate holes in accordance with the
type of wall anchor used.
5. Install the enclosure on the wall.
6. Check that the mounting is secure and the wiring
connections are correct and tight. Check that no
loose wire strands or other metal objects that could
cause a short circuit are on the circuit board.
7. Complete wiring as described in the Applying
Power section.
Applying Power
When using an enclosure type of E-Link Gateway,
power can be supplied from either a separate power
supply or the main terminal strip in the chiller panel.
Locate the power source within 0.9 m (3 ft) of the
E-Link Gateway, and protect it with a suitable fuse or
circuit breaker. Ensure the power is supplied from a
dedicated source and not controlled by a programmed
switch.
If the enclosure is mounted on a wall, the wiring from
the power source to the E-Link Gateway must always
run in a suitable conduit. To obtain the best
Electromagnetic Interference (EMI) and
Electromagnetic Compatibility (EMC) performance,
ensure that the conduit is bonded to the metal of both
enclosures. Scraping the paint around the knockouts
usually helps provide a better electrical connection
between the joining parts.
1. Connect a 1.29-1.02 mm (16-18 AWG) wire from a
reliable ground reference to the E-Link Gateway’s
incoming power ground lug. Do not remove the
existing wire that connects the ground lug to the
enclosure cover.
2. On 120 VAC applications, connect the Hot wire to
TB2 and the Neutral wire to TB1. Connect the
ground wire to a ground lug.
On 240 VAC applications, connect the Hot wire to
TB3 and the Neutral wire to TB1. Connect the
ground wire to a ground lug.
IMPORTANT: When wall mounting, make sure
there is no interferencewith other components in the
near vicinity. Use appropriate conduit to connect the
power and communications wiring.
IMPORTANT: Be careful not to damage the circuit
boards during installation.
YORK Chiller
Micro Panel
Template for Mounting
on a Wall
Conduit
E-Link
Enclosure
FIG:WllMnt
Figure 5: Wall Mounting
!
WARNING: Risk of Electric Shock.
Disconnect or isolate all power supplies
before making electrical connections.
More than one disconnect or isolation
may be required to completely
de-energize equipment. Contact with
components carrying hazardous voltage
can cause electric shock and may result
in severe personal injury or death.
!
CAUTION: Risk of Property Damage.
Do not apply power to the system before
checking all wiring connections. Short
circuited or improperly connected wires
may result in permanent damage to the
equipment.
IMPORTANT: Use copper conductors only.
Make all wiring connections in accordance with
local, national, and regional regulations. Do not
exceed the E-Link Gateway’s electrical ratings.

E-Link Gateway Installation Instructions 7
Commissioning a Standard Application
Once the E-Link Gateway has been mechanically and
electrically installed (that is, it has been located in its
enclosure, wired, and terminated appropriately), it may
be Quick Commissioned.
1. Apply power and verify that the red power
Light-Emitting Diode (LED) on the IPU-II board is
on. Make sure the T-switch is set to OFF, and then
set the required Media Access Control (MAC)
address. Set the MAC address in accordance with
the system integrator to ensure that a unique
address is used. If any non-standard setup is
required, refer to the E-Link Commissioning and
Troubleshooting Guide (LIT-12011238) for more
details.
2. Based on the equipment to be integrated (see
Table 8) and the required BAS output protocol (see
Table 9), select the appropriate settings on
GROUP A and GROUP B switches. For equipment
points lists, refer to the Johnson Controls Portal
(Products and Services>Delivery>Products/
Service Field Support>Equipment
Integration>YORK Equipment Data Maps).
3. Press, hold a few seconds, then release the push
button shown in Figure 11. The status LED flashes
quickly. After the E-Link Gateway re-initializes, the
commissioning is complete.
4. When commissioning a LONWORKS BAS output
protocol, disconnect the BAS network and cycle
the power on the E-Link Gateway to activate the
Quick Start and the LONWORKS FTT10 ProtoCessor.
The ProtoCessor does not recognize the push
button as a trigger to reset and load the correct
conversion file. Wait a minimum of 10 minutes
before reconnecting the BAS network.
5. Check the E-Link Gateway’s LEDs. First, check the
STATUS LED; if the E-Link Gateway has no errors,
it flashes continuously (1/2 second on, 1/2 second
off). If the LED is not flashing continuously, see
Table 6 for possible reasons.
FIG:PwrConn
Figure 6: Power Connection Shown as 120 VAC
Table 5: Allowable MAC Addresses
Protocol Max Allowable Switch
Settable MAC
Addresses
BACnet MS/TP 1 – 127
N2 1 – 127
Modbus RTU 1 – 127

E-Link Gateway Installation Instructions8
6. Place the equipment in remote operating mode to
accept commands from the E-Link Gateway. Refer
to the equipment installation literature for the
proper configuration settings.
For all chillers that use the YORK Talk protocols, check
that the Port 2 communication LEDs, Red (TX) and
Green (RX), are flashing. This scenario indicates that
the chiller panel is being polled and is responding. See
Figure for the location of Port 2 communication LEDs.
What You Should Know before
Using Quick Starts
The E-Link is designed to use a set of predefined data
maps to associate equipment data with a set of fixed
BAS network variables. You are not able to make any
field changes to these data maps; attempting to do so
results in the automatic reversal of any edits that you
may have made. For any field patches, refer to your
local FSC (Field Support Center) for guidance.
The data maps used by the E-Link Gateway are based
on a collection of version controlled equipment point
lists, which are supplied by the equipment business for
the purpose of integrating equipment into BAS
networks. Unless noted otherwise, the equipment’s
data is available in these supported BAS protocols:
BACnet MS/TP, N2, LONWORKS, and Modbus RTU.
The first release of the E-Link was positioned to
provide the equivalent functionality as offered by the
YORK MicroGateway. That release requires you to
reference point lists which are version J or earlier. All
subsequent E-link releases use point lists version K or
later.
Quick Starts 1 through 16 all use the J version point
lists, whereas Quick Starts 17 through 33 use the K
version. The primary difference between the two
categories is that Quick Starts 1 through 16 have
limited network visible points. In this case, the available
points are those which were originally available at the
time when the MicroGateway was first released.
Quick Starts 17 and higher offer a much richer
equipment point compliment that is more reflective of
what the equipment currently makes available today.
These Quick Starts also create profiles that use more
descriptive BACnet point names, use engineering
units, and follow the BACnet Testing Laboratories™
(BTL) guidelines for compliance as a B-ASC controller.
In most cases, using a Quick Start that corresponds to
the equipment being integrated is sufficient to configure
the E-Link Gateway for operating on the BAS network;
however, in some circumstances, you will be required
to provide further customizing by connecting a laptop
computer onto Port 3 and then accessing the User
Reports (refer to the E-Link Gateway Commissioning
and Troubleshooting Technical Bulletin [LIT-12011238]
for more information).
Table 6: LED Status indication
Flash Rate Status LED Indication
LED Off No database configuration is loaded, or no
input power is present.
1 Flash Terminal mode has been invoked (Switch
T is on).
2 Flashes An equipment to E-Link communications
error has occurred.
3 Flashes A Quick Start has a configuration error.
LED On No errors with custom/field modified
application.
Flashing
Continuously No errors with factory standard application.
Table 7: E-Link Releases
Firmware/Database Revision Point Lists
SSM4567 JCF0003BL.BIN J and earlier only
SSM4567 JCF0008BL.BIN J and earlier, or K

E-Link Gateway Installation Instructions 9
Table 8: Equipment Quick Start Selections
APP Group Switch A Equipment Profile Quick Starts
SwitchSettings 32168421Functionality
110 0 0 0 0 1 YK with SSS Imperial (YORK Talk-III) J version points
2 0 0 0 0 1 0 YK with VSD Imperial (YORK Talk-III) J version points
310 0 0 0 1 1 YT with SSS Imperial (YORK Talk-III) J version points
4 0 0 0 1 0 0 YT with VSD Imperial (YORK Talk-III) J version points
510 0 0 1 0 1 YS / YR with SSS Imperial (YORK Talk-III) J version points
610 0 0 1 1 0 YK with SSS Metric (YORK Talk-III) J version points
7 0 0 0 1 1 1 YK with VSD Metric (YORK Talk-III) J version points
810 0 1 0 0 0 YT with SSS Metric (YORK Talk-III) J version points
9 0 0 1 0 0 1 YT with VSD Metric (YORK Talk-III) J version points
1010 0 1 0 1 0 YS / YR with SSS Metric (YORK Talk-III) J version points
11 0 0 1 0 1 1 YORK Talk II, 1200, 1 Section (YORK Talk-II) J version points
12 0 0 1 1 0 0 YORK Talk II, 4800, 1 Section (YORK Talk-II) J version points
1320 0 1 1 0 1 YORK Talk II, 4800, 2 Sections (YORK Talk-II) J version points
14 0 0 1 1 1 0 YD Imperial (YORK Talk-III) J version points
15 0 0 1 1 1 1 YD Metric (YORK Talk-III) J version points
16 0 1 0 0 0 0 ECO2 / YPAL / S100 (BACnet MS/TP via an IPU-I)
17 0 1 0 0 0 1 YK with SSS Imperial (YORK Talk-III) K version points
18 0 1 0 0 1 0 YK with VSD Imperial (YORK Talk-III) K version points
19 0 1 0 0 1 1 YT with SSS Imperial (YORK Talk-III) K version points
20 0 1 0 1 0 0 YT with VSD Imperial (YORK Talk-III) K version points
21 0 1 0 1 0 1 YS / YR with SSS Imperial (YORK Talk-III) K version points
22 0 1 0 1 1 0 YK with SSS Metric (YORK Talk-III) K version points
23 0 1 0 1 1 1 YK with VSD Metric (YORK Talk-III) K version points
24 0 1 1 0 0 0 YT with SSS Metric (YORK Talk-III) K version points
25 0 1 1 0 0 1 YT with VSD Metric (YORK Talk-III) K version points
26 0 1 1 0 1 0 YS / YR with SSS Metric (YORK Talk-III) K version points
27 0 1 1 0 1 1 YST Imperial (YORK Talk-III) K version points
28 0 1 1 1 0 0 YIA Imperial (YORK Talk-III) K version points
29 0 1 1 1 0 1 YST Metric (YORK Talk-III) K version points
30 0 1 1 1 1 0 YIA Metric (YORK Talk-III) K version points
31 0 1 1 1 1 1 YEWS-D1/YEAS/YGAS (Modbus native)
32 1 0 0 0 0 0 YD Imperial (YORK Talk-III) K version points
33 1 0 0 0 0 1 YD Metric (YORK Talk-III) K version points
34 1 0 0 0 1 0 YMC2 Imperial (YORK Talk-III) K version points
35 1 0 0 0 1 1 YMC2 Metric (YORK Talk-III) K version points
63 1 1 1 1 1 1 Reserved for Field adjustments
1. A Quick Start that references a Solid State Starter (SSS) is also applicable to a mechanical starter.
2. Two sections are required for equipment equipped with three or more compressors, or two systems.

E-Link Gateway Installation Instructions10
Table 9: BAS Output Protocol Quick Start Selections
APP Group
Switch B Output Protocol Quick Starts
SwitchSettings 8421Port1 Port3 Port4
0 1
1. When making edits to User Report 4 (Port Configuration), Group Application Switch B must be set to zero. This setting
ensures that the edits are stored. Otherwise, the edits are overwritten to the default values assigned to the particular Group
Switch B setting the next time E-Link is reset, or power is cycled. Edits made in any other User Reports do not require
alterations to either bank of Group Application switches. For standard set-up, not requiring modifications via User Report 4,
use application switch B, settings 1 to 14.
0000MS/TP,AUTO,N,8,1 Modbus,19,200,N,8,1 Terminal
1 2, 5
2. The Terminal setting on Port 4 is restricted for factory use only.
To comply with the LONMARK® specification, all data transmitted on the LONWORKS network must be expressed in SI units
(metric units). The LONWORKS ProtoCessor performs no unit conversions; it assumes that the data supplied is already
correctly expressed.
0001MS/TP,AUTO,N,8,1 Modbus,19,200,N,8,1 Terminal
2 2, 5 0010MS/TP,AUTO,N,8,1 Modbus,19,200,N,8,2 Terminal
3 2, 5 0011MS/TP,AUTO,N,8,1 N2,9,600,N,8,1 Terminal
4 2, 5 0100N2,9,600,N,8,1 MS/TP,38,400,N,8,1 Terminal
5 2, 5 0101Modbus, 19,200, N, 8, 1 MS/TP, 38,400, N, 8, 1 Terminal
6 2, 5 0110Modbus, 19,200, N, 8, 2 MS/TP, 38,400, N, 8, 1 Terminal
7 2, 5 0111Modbus, 9,600, E, 8, 1 MS/TP, 38,400, N, 8, 1 Terminal
8 2, 5 1000Modbus, 9,600, N, 8, 1 MS/TP, 38,400, N, 8, 1 Terminal
93, 5, 6
3. Use Quick Start 9 and 11 if the equipment is supplying the data in SI units (the E-Link is not required to perform any
conversions, so it operates in pass-through mode).
1001N2,9,600,N,8,1 Modbus,19,200,N,8,1 L
ONWORKS – Pass through
10 4, 5, 6
4. Use Quick Start 10 and 12 if the equipment is supplying the data in Imperial units and the E-Link is required to convert these
units into SI.
5. Setting Switch T = ON, on the MAC address, forces TERMINAL mode of Port 3, at 57,600 baud, N, 8, 1. This setting is only
required to debug the E-Link Gateway’s operation, or access the User Reports.
6. Select Quick Starts 9 and 10 when connecting the E-Link Gateway to an ECO2 unit.
1010N2,9,600,N,8,1 Modbus,19,200,N,8,1 L
ONWORKS – Conversion
11 3, 5 1011Modbus, 19,200, N, 8, 2 N2, 9,600, N, 8, 1 LONWORKS – Pass through
12 4, 5 1100Modbus, 19,200, N, 8, 2 N2, 9,600, N, 8, 1 LONWORKS – Conversion
13 2, 5 1101Modbus, 9,600, E, 8, 1 Modbus, 19,200, N, 8, 2 Terminal
14 2, 5 1110MS/TP,38,400,N,8,1 N2,9,600,N,8,1 Terminal
15 7
7. Quick Starts 15 on APP Group B, and 63 on APP Group A, are reserved for field adjustments.
1111Reserved Reserved Terminal