Johnson Controls MAP 1850 User manual

© 2016 Johnson Controls, Inc.
Part No. 24-10737-83, Rev. A
SMART Chiller Access Portal (SC-AP)
Gateway
SC-AP Gateway is a specialized version of the MAP
Gateway for use with SMART Connected Chillers (SCC).
• Access SC Equip cards on Smart Chillers using
Wi-Fi, Ethernet networks, or cellular modems.
•Send chiller data to the cloud for remote storage and
operations as part of our SCC Solution.
IMPORTANT: Save this guide. It contains default
user name and password information that may be
needed if you need to reset your SC-AP Gateway to
factory defaults.
European Single
Point of Contact: NA/SA Single Point of Contact:
JOHNSON CONTROLS
WESTENDHOF 3
45143 ESSEN
GERMANY
JOHNSON CONTROLS
507 E MICHIGAN ST
MILWAUKEE WI 53202
USA
APAC Single Point of Contact:
JOHNSON CONTROLS
C/O CONTROLS PRODUCT MANAGEMENT
NO. 22 BLOCK D NEW DISTRICT
WUXI JIANGSU PROVINCE 214142
CHINA
QUICK START GUIDE
SMART Chiller
Access Portal
Gateway
Connect to Remote Services
This step assumes that you have already con-
figured a cellular router or have access to a good Ether-
net network for communications with the data cloud. Go
to the Wi-Fi client screen in SC-AP.
a. If you are using a cellular connection to access the
chiller communications card go to the SC Equip App
for your device and navigate to Settings > Wi-Fi
Client and set the Enabled field to On using the
drop down list.
b. If you are using an Ethernet connection to access
the chiller communications card go to the SC Equip
App for your device and navigate to Settings >
Ethernet and set the Enabled field to On using the
drop down list.
c. Go to Settings > Remote Services and Enter the
Remote Services Credentials (Segway) received via
email.
d. The MAP1850 device comes online. If the SC-AP is
out of date it updates as soon as connected to the
cloud. This can take 5 to 20 minutes. After updating
a Disconnect message appears. After 7 minutes the
SC-AP reboots and is ready for operation.
Refer to the Mobile Access Portal Gateway Network and
IT Guidance Technical Bulletin (LIT-12012015) for
information on Security Certificates.
Use the SC-AP Gateway
Once a data connection appears to be estab-
lished, use the CSD Mobile Application to
ensure that data is flowing and the connection is healthy.
IMPORTANT: Keep your SC-AP Gateway in the
optional protective shell or stationary cradle with
which it shipped. These may help protect the unit if it
is dropped.
6
7

GETTING STARTED
Refer to the Smart Chiller Access Portal Gateway Installation Instructions (Part No. 24-10737-75) for important product application information.
Connect the SC-AP Gateway to
Equipment
Use the supplied RJ-12 cable or field bus
adapter to connect the RS-485 port of the
SC-AP Gateway to the CS RJ Jack (Connected Service)
port on the SC Equip card. If mounting remotely, use an
approved power supply. The SC-AP Gateway is not
rated for outdoor use. If attaching to a chiller that is
installed outdoors, you must mount the SC-AP Gateway
remotely indoors. Refer to the SMART Chiller Access
Portal Installation Instructions (Part No. 24-10737-75) for
use cases and mounting instructions.
The SC-AP Gateway LEDs
flash, indicating that the device
is initializing. When the Fault
LED turns off and the Wi-Fi
LEDs flash in succession, the
SC-AP Gateway is ready to
use.
Connect to the
SC-AP Gateway
Wi-Fi Network
In the Wi-Fi settings of your mobile device or laptop, con-
nect to the SC-AP
Gateway Wi-Fi network using the following default cre-
dentials:
1
2
Place Label
Here.
SSID:
Passphrase:
Open a Web Browser
Direct your browser to www.mapgwy.com to open the
SC-AP Gateway browser interface.
SC-AP Gateway ships with a private
mapgwy.com SSL certificate installed to ensure secure
communication with the SC-AP Gateway. However, this
certificate does not indicate that it is trusted in a browser.
If you wish to install your own certificate, refer to Installing
a Security Certificate on a Client That is Connecting to
MAP Gateway in the Mobile Access Portal Gateway
Network and IT Guidance Technical Bulletin (LIT-
12012015) for more information.
Log in to the SC-AP Gateway
Use the following default Admin login
credentials:
Read and accept the SC-AP Gateway license agreement.
Change Passwords
The first time you log in to the SC-AP Gateway,
the Change Password and Passphrase web
page appears. You must change the Admin password and
Wi-Fi passphrase.
3
4
Place Label
Here.
User:
Password:
5
a. Replace the default password in the New Admin
Password field. Confirm the change by entering the
new password in the Verify New Admin Password
field.
b. Replace the Wi-Fi Passphrase in the New Wi-Fi
Passphrase field and click Save.
c. Log in to the SC-AP with new credentials.
Continue to Step 6.
IMPORTANT: After you change the Wi-Fi passphrase
or SSID, the web server restarts and you must
rejoin the SC-AP Gateway Wi-Fi network using the
new passphrase. On some mobile devices, you must
select and forget the original SC-AP Gateway Wi-Fi
network before rejoining the network with the new
passphrase.