Judo PURE TAP User manual

Attention:
Carefully read through the instal-
lation and operating instructions
and safety information before
installing and putting the unit into
service.
These instructions must always
be issued to the owner/user.
Installation and
operating instructions
JUDO PURE@TAP
Under-sink water filter
Language: English
Fig.: JUDO PURE@TAP

2 JUDO PURE@TAP
Inquiries, orders, customer support
JUDO Wasseraufbereitung GmbH
P.O. Box 380
71351 Winnenden
Germany
e-mail: [email protected]
judo.eu
Address
JUDO Wasseraufbereitung GmbH
Hohreuschstraße 39 - 41
71364 Winnenden
Germany
Trademarks:
Trademarks used in this document are protected
and registered trademarks of the respective
holder.
© JUDO Wasseraufbereitung GmbH
71364 Winnenden
Germany
All rights reserved.
Reprints – even of extracts – is only permitted
with special approval.
Dear customer,
we would like to thank you for your con-
fidence in us, which you have shown by
purchasing this device. The product you
have purchased is an under-sink water
filter developed using state of the art
technology.
This under-sink water filter is suitable for
use in cold drinking water up to a maxi-
mum ambient temperature of 30 °C
(86 °F).
The under-sink water filter operates on
the basis of a 2-stage function principle
with silver protection.
1st stage activated carbon:
Coarse particles, chlorine, organic com-
pounds are removed from the water.
2nd stage micro-filtration:
The 0.2 µm fine pores of the hollow fibre
membrane retain reliably numerous bac-
teria, fungi, parasites and fine particles
larger than the pore diameter.
Each unit is thoroughly checked before
delivery. Should difficulties nevertheless
occur, please contact the responsible
customer service. See back page.

JUDO PURE@TAP 3
About this instruction manual
Table of contents
1. About this instruction manual.......... 3
1.1 Used symbols................................. 4
1.2 Safety indications and dangers due
to non-compliance.......................... 4
1.3 Units used ...................................... 4
2. Intended use ...................................... 5
2.1 Water pressure............................... 6
2.2 Notes on special dangers............... 6
3. Product indication............................. 7
3.1 Intended purpose ........................... 7
4. Installation ......................................... 7
4.1 General .......................................... 7
5. Service.............................................. 12
5.1 Commissioning............................. 12
5.2 Functional description .................. 12
5.3 Modifications / Changes /
Spare parts................................... 12
5.4 Stoppages .................................... 12
5.5 Replacing the cartridges .............. 13
6. Faults................................................ 15
7. Maintenance..................................... 16
7.1 Cleaning....................................... 16
8. Warranty and services .................... 16
9. Accessories ..................................... 16
9.1 Faucet JUDO design.................... 16
10. Data sheet ........................................ 17
10.1 Type ............................................. 17
10.2 Technical data.............................. 17
10.3 Installation dimensions................. 17
11. Spare parts....................................... 18
12. Customer service ............................ 20
1. About this instruction
manual
ATTENTION
(see chapter “Safety indications and
dangers due to non-compliance”)
The instruction manual must be permanent-
ly available at the place of action of the un-
der-sink water filter.
This instruction manual shall make it easier
to become acquainted with the under-sink
water filter and to make use of its intended
application possibilities.
The instruction manual contains important
information to use the under-sink water filter
in a safe, appropriate and economical way.
It contains fundamental information, which
must be observed during installation, opera-
tion and maintenance. The observance of
these tips helps to avoid dangers, reduce re-
pair costs and increase the reliability and
service life of the under-sink water filter.
The instruction manual must be read and
used by each person entrusted with carrying
out the work on the under-sink water filter,
for example:
–Installation
–Operation
– Maintenance (servicing, inspection, re-
pair)
Installation and maintenance may only be
carried out by personnel authorized by the
manufacturer, who are capable of fulfilling
the instructions given in the installation and
operating instructions and the country-spe-
cific regulations.
Apart from the instruction manual and the le-
gally binding accident prevention provisions
applicable in the country and place of use,
the recognized specific technical regulations
for safe and proper work must also be ob-
served.

4 JUDO PURE@TAP
About this instruction manual
Therefore, this instruction manual must al-
ways be read by the fitter and the responsi-
ble skilled personnel/user before the instal-
lation, putting into service and maintenance.
Not only the general safety notes given in
the chapter “Intended use” are to be ob-
served, but also the special safety notes
inserted under the other main items.
1.1 Used symbols
The safety notes contained in this instruction
manual are labelled with the following sym-
bols:
Notes directly attached to the under-sink
water filter, e.g.
– flow direction (see fig. 1)
– type plate
– cleaning advice
must obligatorily be observed and kept in a
fully legible condition.
1.2 Safety indications and dangers
due to non-compliance
In detail, the non-compliance with the gener-
al danger symbols can result, for example,
in the following risks:
– Failure of important functions of the
under-sink water filter.
– Danger to persons due to electrical and
mechanical effects.
– Danger to persons and the environment
due to leaks.
Refrain from any safety-critical method of
practice.
Non-compliance with this instruction manual
and the safety information can not only re-
sult in dangers for persons but can also
harm the environment and the under-sink
water filter.
1.3 Units used
In derogation of the International System of
Units (SI = System International), the follow-
ing units are used:
ATTENTION
Notes on
existing dangers
Warning, electrical voltage
Tightening torques specified
by the manufacturer
Tips for use and other
informations
Fig. 1: Built-in rotary flange
Unit Conversion
°F °F = 9/5 °C + 32
bar 1 bar
= 105Pa
= 100 kPa
= 0.1 N/mm²
= 14.5 psi

JUDO PURE@TAP 5
Intended use
2. Intended use
The installation and operation of the under-
sink water filter is subject to the always exist-
ing national regulations as they may be.
In addition to the operating instructions and
the obliging regulations concerning accident
prevention that is valid in the user country
and the location of use, the approved spe-
cialist technical regulations concerning safe
and skilled work, should also be observed.
It is absolutely essential that the manufac-
turer / supplier will be consulted before using
water of a different quality, respectively wa-
ter that contains additives.
This under-sink water filter is suitable for use
in cold drinking water up to a maximum am-
bient temperature of 30 °C (86 °F).
The under-sink water filter has been devel-
oped and manufactured using state of the
art technology and the approved safety re-
gulations in Germany.
The under-sink water filter may only be used
as described in the operating instructions.
Any other application or application beyond
that, is to be considered as not intended. Ad-
ditional dangers exist in the case of not in-
tended utilization and of non-compliance
with the danger symbols and safety instruc-
tions. The manufacturer / supplier cannot be
kept liable for any damages issuing from
this. Solely the user bears the full risk.
The intended use also includes the obser-
vance of the operating instructions.
Before an use of the under-sink water filter
beyond the application limits stated in the
operating instructions the manufacturer /
supplier has to be obligatorily talked with.
The under-sink water filters may only be
used in a technical condition, free from de-
fects, in accordance with the instruction,
safety-conscious and danger-conscious
with respect to the operating instructions!
Any functional defects are to be removed
immediately!

6 JUDO PURE@TAP
Intended use
2.1 Water pressure
The water pressure has to be between 1 bar
(14.5 psi) and 3,45 bar (50 psi).
The water pressure must not fall below 1 bar
(14.5 psi) as otherwise the operation can be
impaired! If the filter is not maintained regu-
larly an elevated pressure loss can come
about and this can impair the filter function.
ATTENTION
(see chapter “Safety indications and
dangers due to non-compliance”)
At a water pressure higher than 3,45 bar
(50 psi), a pressure reducer has to be fitted
before the under-sink water filter (see fig. 2).
In modern sanitary installations (in particular
where single lever mixers are used), despite
normal system pressure conditions, peak
pressures of up to over 30 bar (435 psi) fre-
quently occur. This can cause damages.
The optimum operating pressure for the un-
der-sink water filter is between 2 bar (29 psi)
and 3,45 bar (50 psi). In this case the under-
sink water filter works most economically.
2.2 Notes on special dangers
2.2.1 Electrical equipment /
installations
Electrical devices / equipment that are not
splash-water proof and are situated in the di-
rect vicinity of the under-sink water filter may
be damaged by water escaping from the un-
der-sink water filter caused as a result of the
device being operated improperly . In addi-
tion short circuits may come about if these
electrical devices / equipment
are / is con-
nected to the electrical power supply. In the
event of such cases, there is the danger of
electric shock for persons. Therefore all the
electrical devices / equipment situated in the
direct vicinity should be splash-water proof,
respectively comply with the statutory re-
quirements for wet areas (NEMA type 12 /
IP44).
Fig. 2: Pressure reducer upstream of the unit
There must not be any electrical
cables and devices underneath or
in the immediate vicinity of the un-
der-sink water filter!
1
1 = Pressure reducer

JUDO PURE@TAP 7
Product indication
3. Product indication
3.1 Intended purpose
This under-sink water filter is suitable for the
use in cold drinking water up to a water tem-
perature of maximum 30 °C (86 °F).
ATTENTION
(see chapter “Safety indications and
dangers due to non-compliance”)
Concerning use restrictions, see chapter
“Intended use”, please.
4. Installation
4.1 General
ATTENTION
(see chapter “Safety indications and
dangers due to non-compliance”)
The installation may only be effected by
qualified personal.
The chapter “Intended use” has to be ob-
served imperatively!
For an easy operating and maintenance the
indicated distances have to be kept categor-
ically (see chapter “Installation dimen-
sions”).
Appropriate mounting place:
Concerning its mounting place the under-
sink water filter is intended to be installed di-
rectly under the sink (see chapter “Modifica-
tions / Changes / Spare parts”).
The protection towards the drinking water
network has to be executed in accordance
with the local regulations.
ATTENTION
The water supply has to be closed before
the installation and may only be reopened
after the mounting having been completely
finished. In case of non-observance water
damages can arise.
If the water filter hasn’t been put into service
for longer time, the standing water should be
removed. Open the faucet and let the water
run during approximately five minutes.
When installing, all the parts have to be
mounted. Due to non-observance, its func-
tion can be compromised.
When installing and replacing the car-
tridge pay attention to scrupulous clean-
liness.
Through dirt on your hands, during the in-
stallation and during the replacement of
parts, bacterial impurities of the drinking
water installation can be caused.
Fig. 3: JUDO PURE@TAP
Under sink installation

8 JUDO PURE@TAP
Installation
4.1.1 Requirements: Mounting place
The room where the unit is installed must
be dry and frost free!
Unauthorised persons must not have ac-
cess to the under-sink water filter!
ATTENTION
(see chapter “Safety indications and
dangers due to non-compliance”)
The ambient temperature must not exceed
30 °C (86 °F)!
Do not connect to the hot water system!
The under-sink water filter should not be ex-
posed to direct sunlight, to avoid deforma-
tions in the plastic parts.
Before starting the mounting the water sup-
ply line has to be shut off at the correspond-
ing water conduit. The under-sink water filter
is to be installed into the cold water line be-
fore the water tap
.
Pay attention to the flow direction (see
fig. 4)!
4.1.2 Wall holder installation
There has to be enough space for the wall
holder
installation (see chapter “Installation
dimensions”).
Mount the wall holder below the sink with the
aid of the cross-head screws.
The
wall holder has to be installed in a way
that the under-sink water filter is freely ap-
proachable in order to effectuate the car-
tridge replacement.
4.1.3 Installation of the faucet
(Accessories)
For the fixation of the faucet and the hoses
sufficient space has to be available.
Concerning the installation of the faucet a
round opening of a diameter of 13 mm (0.52
inch) is required. The opening should be in
the sink or in the work disk, close to the sink.
ATTENTION
When drilling an opening into porcelain or
stainless steel the necessary operations
have to be observed.
Installation:
– Drill the opening.
– Run the faucet (1.1) with the escutcheon
(1.2) downwards through the opening.
– Screw together from the bottom the rub-
ber washer (1.3), the locating washer
(1.4) and the star washer (1.5) with the
hexagon nut (1.6).
– Tighten carefully.
– Connect the hose adaptor 7/16"-24 UNS
(1.7) to the faucet (1.1).
– Tighten carefully.
Fig. 4: Flow direction

JUDO PURE@TAP 9
Installation
1.1 Faucet
1.2 Escutcheon with O-ring
1.3 Rubber washer
1.4 Locating washer
1.5 Star washer
1.6 Hexagon nut
1.7 Hose adaptor 7/16"-24 UNS
4.1.4 Mounting of the fresh water
supply line
All the lines connected with this device
may only be mounted on cold water
lines.
– Close the water supply at the angle
valve (see fig. 8).
– Mount the angled inlet valve tightly on
this angle valve.
– Mount the hose adaptor on the angled
inlet valve.
4.1.5 Installation of the under-sink
water filter
Hang the under-sink water filter into the wall
holder .
Pay attention to the flow direction (see
fig. 6)!
Mount both hose adaptors on the under-sink
water filter.
Connect the under-sink water filter via the
hoses with the angled inlet valve and the
faucet.
The hoses have accordingly to be cut short.
Open carefully the cold water line and the
faucet so that the air can escape from the
system. The microfiltration module must al-
so be vented via the bleed screw. The bleed
screw must be slightly unscrewed so that
the air can escape. Retighten the bleed
screw (see fig. 7).
It has to be flushed till the clear water will run
off.
Re-close the faucet.
Fig. 5: Robinet avec kit de raccordement
1.1
1.2
1.3
1.4
1.5
1.6
1.7
Fig. 6: Flow direction

10 JUDO PURE@TAP
Installation
Particles of activated carbon may beco-
me dislodged from the cartridge during
installation. This has no bearing on the
filter function and only underlines the ef-
ficiency of the cartridge type used.
Should these particles prove to be an op-
tical disturbance, please simply rinse the
cartridge for a few minutes before instal-
ling the micro filtration cartridge.
Setting of the filter change indicator:
Move the indicator button on the cover to
the next filter change point-in-time (filter
change every 4 - 6 months at the latest).
The under-sink water filter is ready for
service.
Fig. 7: Bleed screw
Bleed screw under the
flange cover

JUDO PURE@TAP 11
Installation
.
Fig. 8: Installation
Reducer
Wall holder
Faucet
Hose
Angle valve
Hose
Under sink water filter
Angled inlet valve
Hose
adaptor
Hose adaptor

12 JUDO PURE@TAP
Service
5. Service
ATTENTION
(see chapter “Safety indications and
dangers due to non-compliance”)
Always observe the chapter “Intended use”!
5.1 Commissioning
Before starting up (initial putting into service
or start-up after maintenance work), fill the
JUDO PURE@TAP with water and vent!
1
Slowly open the water shut-off valve and
the faucet to vent the system.
2 Slightly loosen the bleed screw as the
microfiltration cartridge must also be
vented.
3Retighten the bleed screw once all the
air has been evacuated (see fig. 7).
4Continue rinsing with at least 3 liters of
water (1 minute at nominal flow) or until
the water is clear.
5Close the faucet.
6
Place the indicator button on the flange
cover for the next filter cartridge replace-
ment (replacement of the cartridge every
4 - 6 months at the latest).
7Verify immediately the tightness and
check again a few hours later.
5.2 Functional description
The under-sink water filter:
– In accordance with the standard NSF /
ANSI 42 for the reduction of chlorine and
the improvement of taste and odor.
– In accordance with the standard NSF /
ANSI 42 for the reduction of germs.
– Removes bacteria, fungi, parasites,
insecticides, herbicides, phenols, ...
– Do not use with water of unknown or
doubtful microbiological quality without
adequate disinfection.
Water filtration in the kitchen to generate
treated drinking water.
Ideally suited for the preparation of drinks
and cooking water.
5.3 Modifications / Changes /
Spare parts
ATTENTION
(see chapter “Safety indications and
dangers due to non-compliance”)
Only original spare parts are to be used!
Independent modifications and changes are
prohibited for safety reasons! Those can im-
pair the function of the under-sink water filter,
they can lead to leaks and in extreme cases
can make the under-sink water filter burst.
5.4 Stoppages
ATTENTION
(see chapter “Safety indications and
dangers due to non-compliance”)
If an under-sink water filter is unscrewed,
observe the chapter “Intended use”!
Fig. 9: Functional description
Activated
carbon
filter cartridge
Micro-filter
cartridge

JUDO PURE@TAP 13
Service
5.5 Replacing the cartridges
1Close the cold water supply shut-off
valve or the water filter shut-off valve.
2Open the faucet to remove the water
pressure.
3Remove the JUDO PURE@TAP water
filter: Press the clamping ring of the hose
adapter back and remove the hoses
from the unit. Remove the water filter
from the wall-mounting.
4Remove the flange cover(s) upward (see
fig. 11).
5Use an Allen key to loosen all four
cylinder head screws.
6Turn the filter housing to the left up to the
limit stop and pull it off downward.
7 Only every 4 years: Remove and
replace the profiled flange seal. The pro-
filed side of the seal must be pointing to-
wards the flange (see fig. 10). Failure to
do so can lead to leakage and water
damage.
8Remove the used replacement car-
tridge.
9Clean the seat of the cartridge in the
housing using the disinfectant cloth
provided.
IMPORTANT: Do not touch any plastic
parts, especially the inside of the filter
housing, or the cartridge, with your bare
hands.
10 Insert the new replacement cartridge in
the built-in rotary flange and press in up
to the limit stop.
11 Insert the cylinder head screws of the
filter housing into the bayonet openings
of the built-in rotary flange, turn to the
right up to the limit stop.
12 Use an Allen key to tighten all four cyl-
inder head screws
13 Replace the flange cover(s).
14 Set the filter-change indicator: Move the
indicator button on the flange cover to
the next filter change point-in-time (filter
change every 4 - 6 months at the latest).
15 Hang the JUDO PURE@TAP water filter
into the wall holder and connect the
hoses and adapters.
16 Open the cold water shut-off valve and
the water filter shut-off valve
.
17 Briefly open the nearest faucet and undo
the bleed screw to vent the water filter.
Always keep the filter elements in the
following order in flow direction:
1. Activated carbon filter cartridge
2. Micro-filter cartridge!
Fig. 10: Built-in rotary flange
profiled flange seal
Select the tightening torque (approx
4 Nm) so that the seal closes and
the water filter is not damaged or
stressed/distorted!
Particles of activated carbon may
become dislodged from the
cartridge during flushing. This has
no bearing on the filter function
and only underlines the efficiency
of the cartridge type used.
Should these particles prove to be
an optical disturbance, please
simply rinse the activated carbon
block filter cartridge for a few
minutes before installing the
micro-filtration cartridge at the
next required cartridge change.

14 JUDO PURE@TAP
Service
Fig. 11: Replacing the cartridges
Flange cover
Built-in rotary flange
Replacement cartridge
Micro-filtration
Cylinder head screw
Filter housing complete
5 mm Allen key
Used cartridge
Micro-filtration
Used cartridge
Activated carbon
Bleed screw
Filter-change indicator
Profiled flange gasket

JUDO PURE@TAP 15
Faults
6. Faults
Help with faults:
Fault Cause Remedy
Water smells
unpleasantly
or has
become
discolored.
The under-sink
water filter has
not been used
over a longer
period.
For hygienic reasons you must let the water run for
approximately 10 minutes. If then condition does not
then improve the cartridge must be replaced.
Water flow
rate falls.
The cartridge is
clogged.
Replace the cartridge.
Premature cartridge replacement is necessary if the
water contains a large proportion of particles or in
case of large water consumption.
(see chapter “Replacing the cartridges”)
Leaks in the
under-sink
water filter.
Under-sink water
filter has been
exposed to higher
temperatures or
solvents.
Close the water shut-off valve and inform the fitter or
the nearest customer service center.

16 JUDO PURE@TAP
Maintenance
7. Maintenance
ATTENTION
(see chapter “Safety indications and
dangers due to non-compliance”)
Always observe the chapter “Intended use”!
7.1 Cleaning
ATTENTION
(see chapter “Safety indications and
dangers due to non-compliance”)
Only use clear, clean drinking water to
clean the housing.
Domestic all-purpose cleaners and glass
cleaners can contain up to 25 % solvents or
alcohol (spiritus).
These substances can chemically attack the
plastic parts, which can lead to brittleness
right up to [brittle] fractures.
These kinds of cleaners must therefore
not be used.
8. Warranty and services
In order to maintain your legal warranty
claim it is necessary for the filter insert to be
replaced every 6 months. For hygiene rea-
sons, depending on the water quality and
water consumption, an exchange at shorter
intervals may be required.
Regular servicing is indispensable in order
to continue to achieve a successful treat-
ment for many years after the unit is put into
service. In the building services sector this is
covered by DIN EN 806-5.
Wherever possible, the regular servicing
work and supply with consumables and
wearing materials, etc. should be carried out
by the specialist trade or the factory’s cus-
tomer service department.
In order to maintain your legal warranty
claim, a visual inspection is necessary every
three months, depending on water con-
sumption.
Clean fittings are prerequisite for hygienical-
ly perfect drinking water.
Regularily clean the faucet with disin-
fectant.
9. Accessories
9.1 Faucet JUDO design
– NSF approved
– with ceramic disc cartridge
– chrome plated: order no. 8115020
nickel brushed: order no. 8115028
Fig. 12: Faucet JUDO design

Data sheet
JUDO PURE@TAP 17
10. Data sheet
10.1 Type
JUDO PURE@TAP
Under sink water filter
Order no.: 8115029
10.2 Technical data
* depending on water quality
10.3 Installation dimensions
Water temperature 5 - 30 °C
(41 - 86 °F)
pH-area 5.5 - 9.5
Water pressure min. 1 bar (14.5 psi)
Water pressure max. 3.45 bar (50 psi)
Replacement interval
of the filter cartridge 4 - 6 months
Flow rate
(at 2 bar / 29 psi)
2 l/min
(0.53 US gpm)
(0.44 GB gpm)
Total capacity of filter
cartridge
MF: 2000 l*
(525 US gal)
(440 GB gal)
AC: 2000 l*
(525 US gal)
(440 GB gal)
Effective filter value 0.2 micron
(0.0002 mm)
Bacteria removal value:
E. coli, Vibrio Cholerae, Shi-
gella, Salmonella Typhi,
Klebsiella Terrigena, Crypto-
sporidium, Giardia
> 99.99 %
ABCD
240 mm
(9.45 inch)
145 mm
(5.7 inch)
72 mm
(2.83 inch)
81 mm
(3.19 inch)
Fig. 13: Installation dimensions

18 JUDO PURE@TAP
Spare parts
11. Spare parts
13
11
10 12
A
15
16
17
18
D
E
I
B
II
20 19
F
14
2
3
4
5
1
9
8
6
C
97
C
III

JUDO PURE@TAP 19
Spare parts
Replacement interval: **** = 4 years, ****** = 4 - 6 months depending on water quality and consumption
Spare parts list JUDO PURE@TAP
Item Designation (recommended average replace-
ment interval for wearing parts [*]) Piece(s) Order no. AU1) /
piece
A
Replacement set
Cartridges activated carbon / micro-filtration
****** 1 8115025
price acc. to
current price
list
B Spare parts set Flange cover, complete 1 2110105 27
C Reducer, complete 1 2110040 6
D Wall holder 1 2110065 AU2)
E Spare parts set Filter hood **** 1 2110102 69
F Spare parts set
Cylinder head screw M6x12 1 2110111 1
1 Angled inlet valve 1 1610667
2 Hose adaptor ¾
" F, for hose ø 8 mm 1 1130449
3 Hose ø 8 mm, 1 m long 2 2110115
4 Hose adaptor ¼
" M, for hose ø 8 mm 2 1130377
5 Allen key 5 mm DIN 911 1 1650006
6 Reducer, machined ¾
" M x ¼ " F 1 2110119
7 Reducer ¾
" M x ¼ " F 1 1980268
8 Check valve 1 1980283
9 O-ring 22x3 2 1200229
10 Flange cover, printed + type plate DE 1 2110118
11 Flange cover, printed 1 2110022
12 Indicator button, red 2 1120397
13
Cylinder head screw M6x12 1 1650383
14 O-ring 5,28x1,78 1 1200336
15
Cylinder head screw M6x30 8 1650209
16
Profiled flange seal, precut 2 2460016
17
Filter hood, special 2 2080124
18 Flange, chrome plated 2 2270091
19
Wall holder 1 1400152
20
Pan head screw 2 1650457
Accessories
Item Designation Piece(s) Order no.
IFaucet, chrome plated 1 8115020 price
according to
current
price list
IFaucet, nickel brushed 1 8115028
II LEGIOLAX silver coated spiral **** 1 8230001
III Connection **** 1 2110116 AU2)
1) AU = accounting unit (Items without AU are only available in a set.)
2) Accounting unit not yet defined at press time.

20 JUDO PURE@TAP
Customer service
12. Customer service
All illustrations, dimensions and information for the different models are those valid on the date of prin-
ting. All rights are reserved for modifications as a result of technical progress or further developments.
Claims with regard to models or products are excluded.
1701734 • 2014/01
JUDO Wasseraufbereitung GmbH
Postfach 380 • D-71351 Winnenden
Tel. [phone] / 692-0
e-mail: [email protected] • judo.eu
JUDO Wasseraufbereitung GmbH • Niederlassung Österreich
Zur Schleuse 5 • A-2000 Stockerau
Tel. [phone] / 6 40 78 • Fax [phone] / 6 40 79
e-mail: [email protected] • judo.eu
JUDO Wasseraufbereitung AG
Industriestrasse 15 • CH-4410 Liestal
Tel. [phone] • Fax [phone]
e-mail: [e-mail] • judo-online.ch
JUDO Wasseraufbereitung GmbH • Filiaal-Filiale BeNeLux
Laarbeeklaan-Av. du Laerbeek, 72 A1 • B-1090 Brussel-Bruxelles
Tel./Tél. [phone] • Fax [phone]
e-mail: [email protected] • judo.eu
JUDO France S.à.r.L
76 Rue de la Plaine des Bouchers (Technosud) • F-67100 Strasbourg
Tel. [phone] • Fax [phone]
e-mail : [email protected] • judo.fr
Installed by:
JUDO PROFI-PLUS / PROMI
Backwash protective filter / Germ protection class do-
mestic water station with point rotation system for op-
timum cleaning of the filter insert.
JUDO i-soft TGA 2
The world's first automatic, intelligent water
softener.
JUDO JRSF Backwashing
protective filter
The classic with patented filter sys-
tem. Compact, robust, tried and tes-
ted thousands of times. Numerous
versions from 1" to DN 200
JUDO JU-WEL Trio
“Jewelling” unit with
amethyst, rock crystal and
rose quartz healing stones.
Wellness pure with “jewelled”
water.
JUDO BIOSTAT-COMBI-
MAT
The anti-lime protection and hygi-
ene unit to be used in domestic
water installations. Stops lime -
without replacing the cartridge -
and fights germs.