Jung FST1240EB User manual

Radio push-button controller, built-in
Radio Management
Radio push-button controller, built-in
Art. No. : FST1240EB
Operating instructions
1 Safety instructions
Electrical equipment may only be installed and fitted by electrically skilled persons.
Serious injuries, fire or property damage possible. Please read and follow manual fully.
Danger of electric shock. The 1...10 V control voltage is a functional extra-low voltage
(FELV), and can be connected to mains potential. On installing, ensure safe separation to
SELV/PELV systems. In order to disconnect the connected luminaires, disconnect both
the mains voltage and control voltage circuits.
Danger of electric shock. Device is not suitable for disconnection from supply voltage.
The radio communication takes place via a non-exclusively available transmission path,
and is therefore not suitable for safety-related applications, such as emergency stop and
emergency call.
Do not shorten, extend or strip the antenna. Device can be damaged.
These instructions are an integral part of the product, and must remain with the end
customer.
2 Device components
Figure 1
(1) Radio control unit
(2) LED
(3) Programming button
(4) Antenna
3 Function
System information
By statute, the transmitting power, the reception characteristics and the antenna cannot be
changed.
The range of a radio system from the transmitter to the receiver depends on various
circumstances.
1/5
32532333
J0032532333 08.09.2016

The range of the system can be optimised by selecting the optimal installation location, taking
into account the structural circumstances.
Figure 2: Reduced range due to structural obstacles
Example of penetration of various materials:
Material Penetration
Wood, Plaster, Plasterboard approx. 90%
Brick, Chipboard approx. 70%
Reinforced concrete approx. 30%
Metal, Metal grid approx. 10%
Rain, Snow approx. 1-40%
Intended use
- Radio-controlled switching and brightness setting for lamp operating devices with 1-10 V
interface
- Installation in false ceilings or surface mounting
- Operation with suitable radio transmitters
iIt is not possible to teach a combination of presence detector and motion detector.
Product characteristics
- Switch-on brightness can be saved permanently
- Switch-on via bulb-preserving soft start
- Light scene operation possible
- Constant light regulation possible in connection with a radio presence detector
- Run-on time of approx. 1 minute in connection with radio motion detectors
4 Operation
A radio transmitter has to be taught in order to be able to operate the device.
iObserve the instructions for the radio transmitter.
2/5
32532333
J0032532333 08.09.2016
Radio Management
Radio push-button controller, built-in

5 Information for electrically skilled persons
5.1 Fitting and electrical connection
DANGER!
Electrical shock when live parts are touched.
Electrical shocks can be fatal.
Before carrying out work on the device or load, disengage all the
corresponding circuit breakers. Cover up live parts in the working environment.
Mounting and connecting the device
Maintain a distance of at least 0.5 m from metal surfaces and electrical devices, e.g. microwave
ovens, hi-fi and TV systems, electronic ballasts or transformers.
Maintain a distance of at least 1 m between transmitter and receiver in order to prevent
overmodulation of the receiver.
Figure 3
oConnect control unit (1) and lamp operating device (5) in accordance with connection
diagram (figure 3).
oIf multiple miniature circuit breakers supply dangerous voltages to the device or load,
couple the miniature circuit breakers or label them with a warning, to ensure release is
guaranteed.
iLay the antenna stretched out freely if possible.
iLay the control cable, ensuring that it is of the appropriate type and cross-section for the
VDE specifications for 250 V cables, control voltage has basic insulation.
iThe maximum number of lamp operating devices that can be controlled by the device is a
function of the maximum connected load. The maximum control current must not be
exceeded (see Technical data).
iOnly use lamp operating devices and fluorescent lamps that are of the same type, the
same power level, and from the same manufacturer. Otherwise there may be differences in
brightness between the individual lamps.
oSwitch on mains voltage.
iThe load can be switched on or off by pressing the programming button briefly (for about
1 second).
3/5
32532333
J0032532333 08.09.2016
Radio Management
Radio push-button controller, built-in

5.2 Commissioning
DANGER!
Electrical shock when live parts are touched.
Electrical shocks can be fatal.
Before working on the device, cover up live parts in the working environment.
iObserve the instructions for the radio transmitter.
Teach-in radio transmitter
iIf all memory slots are occupied, a radio transmitter which has already been taught must
first be deleted. To do this, delete all taught channels and light scenes of the radio
transmitter individually.
The distance between the receiver and the radio transmitter is from 0.5 m to 5 m.
Load is switched off.
oPress the programming button for approx. 4 seconds.
The LED blinks. The device is in programming mode for approx. 1 minute.
oTrigger teach telegram on radio transmitter (see instructions for radio transmitter).
LED lights up. The radio transmitter has been taught.
oPress the programming button briefly.
The load switches on. The device is in operating mode.
iThe programming mode is exited automatically after about 1 minute.
iTeach light scene buttons separately.
iWhen a radio transmitter is taught, All On and All Off buttons that are present are
automatically also taught.
Save switch-on brightness
A set brightness value can be saved in the device as the switch-on brightness.
iIn the state as supplied the switch-on brightness is set to maximum.
oSet light to the required brightness.
oPress programming button for longer than 4 seconds.
Switch-on brightness is saved.
For confirmation the lighting switches off briefly and then on again.
iThe saved switch-on brightness is retained in the event of a power failure.
Deleting radio transmitters individually
oTeach the radio transmitter to be deleted again (see Teaching a radio transmitter).
LED blinks quickly. The radio transmitter has been deleted.
iIf several channels or light scenes of a radio transmitter have been taught, they all must be
deleted individually.
Deleting all radio transmitters
Load is switched off.
oPress the programming button for approx. 20 seconds.
After approx. 4 seconds the LED blinks.
After approx. 20 seconds the LED flashes.
oDuring the next 6 seconds, release the programming button and press it again for approx.
1 second.
LED lights up. The radio transmitters will be deleted.
LED blinks quickly. All radio transmitters have been deleted.
4/5
32532333
J0032532333 08.09.2016
Radio Management
Radio push-button controller, built-in

6 Appendix
6.1 Technical data
Rated voltage AC 230V~
Mains frequency 50 / 60Hz
Control voltage 1 ... 10V
Control current max. 15mA
Ambient temperature 0 ... +55°C
Degree of protection IP 20
Circuit breaker max. 10A
Connected load
Ohmic load 1800W
Electronic ballast Type-dependent
Switching current 8A
Contact type µ contact
Dimensions L×W×H 187×28×28 mm
Radio frequency 433.05MHz ... 434.79MHz
Receiver category 2
Teachable radio transmitter max. 30
6.2 Troubleshooting
Device does not respond, or only sometimes.
Cause 1: battery in the radio transmitter is empty.
Change the battery in the radio transmitter.
Cause 2: Radio range exceeded. Structural obstacles reduce the range.
Check the installation situation.
Check routing of antenna. Laying the antenna stretched out increases the range.
Using a radio repeater.
6.3 Conformity
Albrecht Jung GmbH & Co. KG hereby declares that the radio system type
Art. No. FST1240EB
corresponds to the directive 2014/53/EU. You can find the full article number on the device. The
complete text of the EU Declaration of Conformity is available under the Internet address:
www.jung.de/ce
6.4 Warranty
The warranty follows about the specialty store in between the legal framework as provided for
by law.
ALBRECHT JUNG GMBH & CO. KG
Volmestraße 1
58579 Schalksmühle
GERMANY
Telefon: [phone]
Telefax: [phone]
[email protected]
www.jung.de
5/5
32532333
J0032532333 08.09.2016
Radio Management
Radio push-button controller, built-in