Juniper Flip-and-Fold OP User manual

OP
Flip-and-Fold
Multipurpose Table
Includes Add-Ons: A1 | A2
General Installation Guide Watch Entire
Install Video

TABLE OF CONTENTS
Edition Code
OP :: Flip-and-Fold ..................................................................................... 1
Add-ons
A1 :: Modesty Panel.................................................................................. 11
A2 :: Power and Wire Management............................................. 15

Flip-and-Fold
Overview
Multipurpose Table
All parts listed are for a single multipurpose
table, additional parts will be needed for additional
multipurpose tables.
1
Watch Entire
Install Video

2
FLIP-&-FOLD TABLE
Code Qty. Description
OTF##V2
1Main Frame
1Main Surface
2Leg Post
4Leg Post Cap
2Foot
2Leg Top Cap
4Wire Clips
Parts List

3
FLIP-&-FOLD TABLE
1 | Position Frame on Surface
Turn surface upside down and place frame on surface.
Measure and set frame location.
2 | Secure Frame to Surface
Use (x8) wood screws to secure frame to underside of surface.
Note: Assure frame stays squared.
CENTERED
CENTERED
24" Deep Surface
30" Deep Surface
1.5”
Scan to
Watch Step
Scan to
Watch Step

4
FLIP-&-FOLD TABLE
3 | Measure to Position Release Handle
Center handle on the surface and align flush with surface edge.
Insert (x4) wood screws to secure handle.
4 | Secure Wire Clips
Assure wire is not sitting pass the surface edge. Secure wire clips
with wood screws.
Note: Evenly space out clips for best result.
Scan to
Watch Step
Scan to
Watch Step

5
FLIP-&-FOLD TABLE
5 | Finish Securing Frame
Pull handle to flip up frame base to access additional screw holes.
Insert wood screws to secure frame.
6 | (Optional) Prep Legs for Modesty Panel
Note: If not installing a modesty panel, skip step and proceed to step 7.
6.1 Measure and Position Bolt in Legs
Open modesty panel box and remove measuring stick and hardware.
Slide measuring stick down post leg until measuring stick reaches end.
Slide bolt head from opposite end of post leg until head reaches end of
measuring stick.
Scan to
Watch Step
Scan to
Watch Step

6
FLIP-&-FOLD TABLE
6.2 Secure Bolt to Legs
Hold bolt in position. Slide washer on bolt and hand tighten nut. Lock bolt
position by firmly tightening the nut with wrench.
6.3 Secure Bolts to Frame
On main frame, remove the plastic caps from both ends. Slide bolts down
frame and use smaller side of measuring stick for bolt’s proper placement.
Hold the bolt in position. Slide washer on bolt and hand tighten nut. Lock
bolt position by firmly tightening nut with wrench. Repeat on other end.
Scan to
Watch Step
Scan to
Watch Step

7
FLIP-&-FOLD TABLE
7 | Attach Post Legs to Frame
Place cap onto end of post and into base. Insert socket cap screws
and lock washers to secure legs to frame.
Note: Repeat process for both legs.
Scan to
Watch Step

8
FLIP-&-FOLD TABLE
8 | Attach Feet to Post Legs
Place cap onto end of post, and then set feet on top. Insert socket
cap screws and anti-shake washers to secure feet to legs.
Note: Repeat process for both legs.
Scan to
Watch Step

9
FLIP-&-FOLD TABLE
9 | Tighten Leg Bolts
Confirm pre-installed leg bolts are tightened and flip table to
upright position.
Note: When flipping table, be careful not to damage caster locks.
10 | Snap on Leg Top Caps
When snapping on top caps, press the top part into place followed
by bottom.
Note: Repeat process for both legs.
Scan to
Watch Step
Scan to
Watch Step

10
END OF FLIP-&-FOLD TABLE SECTION

A1: Modesty Panel
Overview
Multipurpose Table
All parts listed are for a single multipurpose
table, additional parts will be needed for additional
multipurpose tables.
11
Watch Entire
Install Video

12
MODESTY PANEL
Code Qty. Description
OMP##
1Steel Modesty Panel
1Modesty Panel Brackets (set of 2)
Parts List

13
MODESTY PANEL
1 | Connect Brackets for Modesty Panel
Fasten brackets to post legs and to main frame following hardware
sequence below. Scan to
Watch Step

14
END OF MODESTY PANEL SECTION
2 | Fasten Modesty Panel to Brackets
Align inside of modesty panel screw holes with bracket’s screw holes.
Insert (x4) screws and tighten. Scan to
Watch Step

A2: Optional Power
Overview
Multipurpose Table
All parts listed are for a single multipurpose
table, additional parts will be needed for additional
multipurpose tables.
15
Watch Entire
Install Video

16
OPTIONAL POWER
Code Qty. Description
PSMA 1Desktop Power Unit
PSJ## 1Jumper
PSPIF144 1Infeed 114" Long
OPCM 1Cable Clip System–Set of 18
Parts List

17
OPTIONAL POWER
i |Perimeter Power System
1. Smart Box Power Infeed
Has a standard NEMA 5-15P 15 amp plug
on one end and a special connector on
the opposite end. This device powers
the system.
2. Desktop Power Unit
Commonly known as a duplex outlet.
Desktop power units come with a 3-port
connector at the end of the cord that
connects to the special connectors of
the power infeed and jumpers.
3. Jumper
A cord with a special connector on each
end that plugs into a desktop power
unit’s 3-port connector. Jumpers connect
desktop power units to other desktop
power units.
Reconfiguration
Tables may be easily reconfigured. Unplug the power infeed from the wall outlet and
disconnect jumpers. Rearrange the tables as required, reconnect jumpers, and reconnect
power infeed. Power infeed can be connected anywhere in the front of desktop units, as
shown below.