Juniper JOT Desk BL-4 User manual

BL-4
JOT Desk
120-Degree Workstation
Includes Add-Ons: A1 | A2 | A3
General Installation Guide

TABLE OF CONTENTS
Edition Code
BL-3 :: Pod of 3 ............................................................................................ 1
BL-3 :: Pod of 6......................................................................................... 13
Add-ons
A1 :: Laminate Surface-Height End Panels............................ 21
A2 :: Laminate Divider-Height End Panels........................... 25
A3 :: Steel Inset End Panels........................................................... 29

Pod of 3
Overview
JOT 120-Degree Workstation
All parts listed are for a Pod of 3; additional parts will
be needed for additional Pods.
1

2
POD OF 3
Code Qty. Description
GB120v2 3Main Surface
BLPB2/
BLBB3
6Long Beam
6Lock Plate
12 Cap Screw
6Locking Screw and Lever
BL48
348”End Leg
12 Wood Screws
KIT-120
3120-Degree Leg w/ Triangular Box
12 Bolts
BCTLM** 1Leg-Mount Cable Tray Hangers
(Set of 2)
CTX N L** 1Leg-Mount Cable Tray
BTEC or
BNTEC** 1Cable Tray End Cap
Parts List
**Add-on items

3
POD OF 3
2 | Connect End Legs, Post Legs and Beams
Insert beam tabs into leg brackets. Guide beam tabs into bracket holes, ensuring
that there is not a gap between the beam and legs. Using a rubber mallet, hammer
beam to lock in place.
1 | Assemble Post Legs (x3)
Place triangle box on post leg and secure with 4 bolts. Attach corner protector on
corner that will be facing toward user when desk is in use.

4
POD OF 3
3 | Bolt Down Beam-to-Leg Lock Plate
Note: Beam lock plates will not fit if there is a gap between beam and leg.
4 | Measure and Adjust Beam Width
Measure from end leg to end leg until you find the approximate width of work surfaces.
Insert screw through overlapping beam slots and into locking screw and lever. Slightly
tighten screw. DO NOT fully tighten. Insert beam grommet covers.
31"
31" 31"
31"
31"
31"
15"
15" 15"

5
POD OF 3
5 | Attach Cable Tray Hangers and End Caps
Align slots on cable tray and secure with 2 bolts from bottom. These hangers will
mount to workstation. Insert Beam Grommet Covers.
NOTE: End Caps (BTEC) are optional, follow the same install process with or
without end caps.
6 | Insert Beam Lock
Adjust cable tray to approximate width of the work surface. Insert screw through over-
lapping beam slots and into the locking screw and lever. Slightly tighten the screw. DO
NOT fully tighten.

6
POD OF 3
7 | Leg Mount Cable Tray
Insert tabs of connector bracket into triangle post leg slots, then use 2 screws to
connect cable tray hanger to bracket. Secure other end of tray directly to end leg using
2 screws. Tighten beam lock.

7
POD OF 3
9 | Surface Installation
Measure from inner surface of leg bracket to outer edge of surface.
Option 1: If installing dividers or monitor arms, leave 1 5/
8”space between surfaces, full
width should be 21 7/
8”.
Option 2: If not installing dividers or monitor arms, leave no space between surfaces, full
width should be 21 1/
16”.
XX
XX
15/8”
TH ES E MEAS UR EM ENTS MAY VAR Y SL IGHT LY DUE TO PRODUC TI ON
TO LE RA NC ES .

8
POD OF 3
11 | Place and Secure First Divider
NOTE: Skip step if not installing dividers. Clamp bracket to surface's side edge and tight-
en vertical bolt against surface to secure bracket. Repeat for all brackets. Lower screen
into brackets and tighten horizontal bolt to clamp brackets onto screens.
10 | Secure First Surface
Place surface on top of frame. Align outer side of surface flush and parallel with
outer side of end leg. Insert wood screws into leg brackets and secure to underside
of surface.

9
POD OF 3
12 | Secure Second Surface
Place second surface on top of frame. Align outer side of surface flush and parallel
with outer side of end leg. Insert wood screws into leg brackets and secure to underside
of surface.
13 | Place and Secure Second Divider
NOTE: Skip step if not installing dividers. Clamp bracket to surface's side edge and tight-
en vertical bolt against surface to secure bracket. Repeat for all brackets. Lower screen
into brackets and tighten horizontal bolt to clamp brackets onto screens.

10
POD OF 3
15 | Secure Support Bars
Place third surface on top of frame. Align outer side of surface flush and parallel with
outer side of end leg. Insert wood screws into leg brackets and secure to underside
of surface.
14 | Place and Secure Third Divider
NOTE: Skip step if not installing dividers. Clamp bracket to surface's side edge and
tighten vertical bolt against surface to secure bracket. Repeat for all brackets. Lower
screen into brackets and tighten horizontal bolt to clamp brackets onto screens.

11
POD OF 3
16 | Tighten Beam Locks

12
END OF POD OF 3 SECTION

Pod of 6
Overview
JOT 120-Degree Workstation
All parts listed are for a Pod of 6; additional parts
will be needed for additional Pods.
13

14
POD OF 6
Parts List
Code Qty. Description
GB120v2 6Main Surface
BLPB2/
BLBB3
12 Long Beam
12 Lock Plate
24 Cap Screw
12 Locking Screw and Lever
BL48
448”End Leg
24 Wood Screws
KIT-120
6120-Degree Leg w/ Triangular Box
24 Bolts
BL48INT
148”Intermediate Leg
8Cap Screw

15
POD OF 6
2 | Assemble Intermediate Leg
Align bracket with leg holes and bolt in place. Connect 4 brackets to leg.
Insert 2 bolts per bracket to secure in place.
1 | Assemble Post Legs (x6)
Place triangle box on post leg and secure with 4 bolts. Attach corner protector on
corner that will be facing toward user when desk is in use.
48"

16
POD OF 6
3 | Connect End Legs, Intermediate Leg, Post Legs and Beams
Insert beam tabs into leg brackets. Guide beam tabs into bracket holes, ensuring
that there is not a gap between the beam and legs. Using a rubber mallet, hammer
beam to lock in place.
Intermediate Leg
Connect to Intermediate Leg

17
POD OF 6
4 | Bolt Down Beam-to-Leg Lock Plate
Note: Beam lock plates will not fit if there is a gap between beam and leg.
x12