Juniper THINK 120-Degree BHALGSA User manual

BHALGSA
THINK 120-Degree
Height-Adjustable Workstation
Includes Add-Ons: A1 | A2
General Installation Guide

TABLE OF CONTENTS
Edition Code
BHALGSA :: Workstation .................................................................... 1
Add-ons
A1 :: Slim Pedestal......................................................................................7
A2 :: Cable Tray......................................................................................... 11

1
Workstation
Overview
THINK 120-Degree Height-Adjustable
All parts listed are for a single workstation;
additional parts will be needed for
additional workstations.

2
WORKSTATION
Code Qty. Description
GB120V2 1Surface
BHALGSA
1Right & Left-Adjustable Beam
1Feet (Set of 2)
223” Arm Bracket
1Center Post Brackets (L, REAR, & R)
1Center Post Base
3Leg with Motor
1Handset
5Glides
3Extension Cords (SHRT, MED, & LG)
1Power Cable
14 Screw (A)
8Screw (B)
2Screw (C)
8Screw (D)
4Screw (E)
39 Screw (F)
2Screw (G)
Parts List

3
WORKSTATION
1 | Assemble Leg Posts Separately
Attach center leg with motor to the center post brackets using screws (A).
Then, attach side legs with motor and arm brackets to left and right
adjustable beams.
Note: Replace the default arm brackets if workstation requires BHA19
or T-brackets.
Right Center Post Bracket
Right Adjustable Beam Left Adjustable Beam
Left Center Post Bracket
Rear Center Post Bracket

4
WORKSTATION
2 | Secure Leg Posts on Surface
Secure leg posts to the surface using screws (F).
Note: If using surface-mounted dividers, keep the frame 1.5 inches inset from the
surface edge. If not using surface-mounted dividers, bring frame flushed to edge
of surface.

5
WORKSTATION
4 | Install Feet, Gliders, and Control Box
Install feet using screws (D) for outside legs. Install center post base to center leg
using screws (E). Mount control box to the post beam using screw (G). Then, secure
power cord to the control box. Mount handset using wood screws (C) and attach
to control box. If workstation is complete, flip over. Reference handset guide for
initialization and operation functions.
Center Post Base
Control Box

6
END OF WORKSTATION SECTION

A1: Slim Pedestal
Overview
THINK 120-Degree Height-Adjustable
All parts listed are for a single slim pedestal;
additional parts will be needed for additional
slim pedestals.
7

8
SLIM PEDESTAL
Code Qty. Description
BFSLM.SM
1Large Mounting Bracket
1Small Mounting Bracket
BFSLM 1Slim Pedestal
BFSLM.HW
8Machine Screw
10 Wood Screw
Parts List

9
SLIM PEDESTAL
1 | Secure Brackets to Slim Pedestal
Align large mounting bracket to front of pedestal and align small mounting
bracket to back. Secure both brackets using provided screws.

10
END OF SLIM PEDESTAL SECTION
2 | Attach Slim Pedestal to Surface
Secure pedestal to surface using wood screws. The pedestal brackets will
connect on either side of the center beam.

11
A2: Cable Tray
Overview
THINK 120-Degree Height-Adjustable
All parts listed are for a single cable tray;
additional parts will be needed for additional
cable trays.

12
CABLE TRAY
Code Qty. Description
BHCT
1Surface-Mount Cable Management
Tray
10 Wood Screws
Parts List

13
CABLE TRAY
1 | Extend Cable Tray to Desired Length
Extension range: 25”–45”.

14
END OF CABLE TRAY SECTION
2 | Attach Cable Tray to Surface
Attach cable tray using wood screws.

1-866-999-0955 | hello@juniperoffice.com | juniperoffice.com
© 2023 Juniper Office | Version 23.0.0