Jura E6 User manual

E6/E60 – Quick Reference Guide

2
E6/E60 – Quick Reference Guide
E6/E60 – Quick Reference Guide
J
These short instructions do not replace the ‘E6/E60 Instructions for
Use’. Make sure you read and observe the safety information and
warnings first in order to avoid hazards.
You can start coffee system rinsing manually at any time.
Precondition:The start screen is displayed.
TPlace a receptacle under the coffee spout.
TPress the ‘ Pc’ button.
TPress the ‘>’ button.
TPress the ‘Rinse the coffee system’ button to start the rinse
operation.
The operation stops automatically.
After each milk preparation, the E6 prompts you to perform a milk
system rinse.
Precondition:‘Rinse the milk system’ is displayed.
TPlace a receptacle under the fine foam frother.
TPress the ‘ Pc’ button.
‘Open switch’
TTurn the switch to the§position.
The fine foam frother is rinsed.
‘Close switch’
TTurn the switch to the °position.
To ensure that the fine foam frother always works properly, you
must clean it daily when you have been preparing milk
If the wrong cleaning agent is used, the machine could be damaged
and/or traces could be left behind in the water.
T Use only original JURA maintenance products.
EJURA milk system cleaner is available from specialised dealers.
Rinsing the machine
Rinsing the fine foam
frother
Cleaning the fine foam
frother
CAUTION

3
E6/E60 – Quick Reference Guide
Precondition:The start screen is displayed.
TPress the ‘ Pc’ button.
TPress the ‘Clean the milk system’ button.
TPress the ‘Start’ button.
TPress the ‘Next’ button.
‘Milk system cleaner’
TRemove the milk pipe from the milk container or milk cooler.
TPour 250ml of fresh water into a receptacle and add 1 capful
of milk system cleaner.
TImmerse the milk pipe in the receptacle.
TPlace a receptacle under the fine foam frother.
TPress the ‘Next’ button.
As soon as the machine has heated up, ‘Open switch’
appears.
TTurn the switch to the§position.
The fine foam frother and the milk pipe are cleaned.
‘Close switch’
TTurn the switch to the °position.
‘Fresh water’
TRinse the receptacle thoroughly, fill it with 250ml of fresh
water and immerse the milk pipe in the water.
TEmpty the other receptacle and place it under the fine foam
frother once more.
TPress the ‘Next’ button.
‘Open switch’
TTurn the switch to the§position.
The fine foam frother and the milk pipe are rinsed with fresh
water.
‘Close switch’
TTurn the switch to the °position.
To make sure the fine foam frother works properly, and in the inter-
ests of hygiene, it must be dismantled and rinsed daily if you have
been preparing milk.
TRemove the milk pipe and rinse it thoroughly under running
water.
TRemove the fine foam frother.
Dismantling and rinsing
the fine foam frother

4
E6/E60 – Quick Reference Guide
TDismantle the fine foam frother into its individual parts.
TRinse all the parts under running water. If there are severely
dried-on milk residues, firstly immerse the individual parts
in a solution of 250ml cold water and 1 capful of JURA milk
system cleaner. Then rinse the parts thoroughly.
TRe-assemble the fine foam frother.
EEnsure that all individual parts are correctly and firmly con-
nected to ensure optimum operation.
TRe-fit the fine foam frother on the milk system.
Your E6 no longer has to be descaled if you are using the CLARIS
Smart filter cartridge.
EOnce the filter cartridge stops working (depending on the
water hardness setting), the E6 will prompt you to change the
filter.
ECLARIS Smart filter cartridges are available from specialised
dealers.
Precondition:The start screen is displayed. The filter symbol !
lights up red (if you are already using a filter and it is depleted).
TRemove and empty the water tank.
TTurn the filter cartridge anticlockwise and remove it along
with the extension from the water tank.
TFit the filter cartridge extension on top of a new CLARIS
Smart filter cartridge.
TInsert the filter cartridge with its extension into the water
tank.
TTurn the filter cartridge clockwise until it audibly clicks into
place.
TFill the water tank with fresh, cold water and reinsert the
tank.
The machine automatically detects that you have just
inserted/changed the filter cartridge.
‘Open switch’
TTurn the switch to the§position.
‘Filter is being rinsed’
‘Close switch’
TTurn the switch to the °position.
Inserting/changing the
filter

5
E6/E60 – Quick Reference Guide
After 180preparations or 80switch-on rinses, the E6 will prompt you
to clean it.
If the wrong cleaning agent is used, the machine could be damaged
and/or traces could be left behind in the water.
T Use only original JURA maintenance products.
EThe cleaning programme lasts approximately 20 minutes.
EDo not interrupt the cleaning programme. The quality of
cleaning will be impaired if you do so.
EJURA cleaning tablets are available from specialised dealers.
Precondition:‘Clean machine’ is displayed.
TPress the ‘ Pc’ button.
‘Clean’
TPress the ‘Start’ button.
TPress the ‘Next’ button.
‘Empty coffee grounds container’
TEmpty the drip tray and coffee grounds container and put
them back into the machine.
‘Clean’
TPlace a receptacle under the coffee spout.
TPress the ‘Next’ button.
‘Machine is being cleaned’, water flows out of the coffee
spout.
The operation is interrupted, ‘Add cleaning tablet’.
TOpen the cover of the filler funnel for the cleaning tablet.
TInsert a JURA cleaning tablet into the filler funnel.
TClose the cover of the filler funnel.
TPress the ‘Next’ button.
‘Machine is being cleaned’, water flows out of the coffee
spout several times.
The operation stops automatically.
‘Empty coffee grounds container’
TEmpty the drip tray and coffee grounds container and put
them back into the machine.
Cleaning the machine
CAUTION

6
E6/E60 – Quick Reference Guide
The E6 builds up deposits of limescale over time and automatically
prompts you to descale it when necessary. The degree of calcifica-
tion depends on the hardness of your water.
EIf you are using a CLARIS Smart filter cartridge, you will not be
prompted to descale.
If the descaling agent comes into contact with the skin or eyes, this
can cause irritation.
T Avoid contact with the skin or eyes.
T Rinse off the descaling agent with clean water. Should you get
any descaling agent in your eye, see a doctor.
If the wrong descaling agent is used, the machine could be dam-
aged and/or traces could be left behind in the water.
T Use only original JURA maintenance products.
If the descaling operation is interrupted, there may be damage to
the machine.
T Allow the descaling programme to run to the end.
If the descaling agent comes into contact with sensitive surfaces
(e.g. marble), damage cannot be ruled out.
T Clean up any splashes immediately.
EThe descaling programme lasts approximately 40minutes.
EJURA descaling tablets are available from specialised dealers.
Precondition:‘Decalcify machine’ is displayed.
TPress the ‘ Pc’ button.
‘Descale’
TPress the ‘Start’ button.
TPress the ‘Next’ button.
‘Empty drip tray’
TEmpty the drip tray and coffee grounds container and put
them back into the machine.
‘Agent in tank’
TRemove and empty the water tank.
Descaling the machine
JCAUTION
CAUTION
CAUTION
CAUTION

7
E6/E60 – Quick Reference Guide
TCompletely dissolve 3JURA descaling tablets in a receptacle
holding 500ml of water. This may take several minutes.
TPour the solution into the empty water tank and insert it
into the machine.
‘Open switch’
TPlace a receptacle under the fine foam frother.
TTurn the switch to the§position.
‘Machine is being descaled’ appears and water flows out of
the fine foam frother repeatedly.
The operation is interrupted, ‘Close switch’.
TTurn the switch to the °position.
‘Machine is being descaled’, the descaling operation is con-
tinued.
The operation is interrupted, ‘Empty drip tray’.
TEmpty the drip tray and coffee grounds container and put
them back into the machine.
‘Rinse the water tank’ / ‘Fill water tank’
TEmpty the receptacle and place it under the fine foam
frother and the coffee spout.
TRemove the water tank and rinse it thoroughly.
TFill the water tank with fresh, cold water and reinsert the
tank.
‘Open switch’
TTurn the switch to the§position.
‘Machine is being descaled’, the descaling operation is con-
tinued.
The operation is interrupted, ‘Close switch’.
TTurn the switch to the °position.
The descaling operation is continued. Water flows out of the
coffee spout.
The operation is interrupted ‘Empty drip tray’
TEmpty the drip tray and coffee grounds container and put
them back into the machine.
EIf the descaling operation stops unexpectedly, rinse the water
tank thoroughly.
3x

8
E6/E60 – Quick Reference Guide
Limescale deposits may form in the water tank. To ensure correct
function of the machine, descale the water tank from time to time.
TRemove the water tank.
TIf you use a CLARIS Smart filter cartridge, remove this.
TCompletely fill the water tank and dissolve 3 JURA descaling
tablets in it.
TLeave the water tank with the descaling solution for several
hours (e.g. overnight).
TEmpty the water tank and rinse it thoroughly.
TIf you use a CLARIS Smart filter cartridge, insert this again.
TFill the water tank with fresh, cold water and reinsert the
tank.
Coffee beans may be covered with a slight oil film which remains on
the walls of the bean container. These traces may negatively affect
the coffee result. For this reason clean the bean container from time
to time.
Precondition:‘Fill bean container’ is displayed.
TSwitch the machine off with the On/Off button Q.
TRemove the aroma preservation cover.
TClean the bean container with a soft, dry cloth.
TFill the bean container with coffee beans and close the
aroma preservation cover.
Descaling the water tank
Cleaning the bean
container
E6_Kurz/en/201909