Jura IMPRESSA C50 User manual

IMPRESSA C50 – Quick Reference Guide
The ‘IMPRESSA C50 Instructions for Use’ together with these short
instructions ‘IMPRESSA C50 – Quick Reference Guide’ has been awarded
the seal of approval by the independent German Technical Inspection
Agency, TÜV SÜD, due to its easy-to-understand style, its thoroughness
and coverage of safety aspects.
Downloaded from ManualsNet.com search engine

2
IMPRESSA C50 – Quick Reference Guide
IMPRESSA C50 – Quick Reference Guide
J
These short instructions do not replace the ‘IMPRESSA C50 Instruc-
tions for Use’. Make sure you read and observe the safety informa-
tion and warnings first in order to avoid hazards.
You can initiate the rinse operation manually at any time.
Precondition: ESPRESSO is displayed (example).
TPlace a receptacle under the coffee spout.
OTTouch the P symbol for approximately 2 seconds until
RINSE appears on the display.
kTPress the Rotary Switch to enter the programme item.
RINSE
kTPress the Rotary Switch to initiate the rinse operation.
RINSING, water flows out of the coffee spout.
The rinse stops automatically. ESPRESSO appears on the
display (example).
EThis chapter applies to the professional fine foam frother
and the fine foam frother.
To ensure that the fine foam frother always works properly, you
must rinse it with water after every milk preparation.
Your IMPRESSA will not prompt you to rinse the fine foam frother.
Precondition: ESPRESSO is displayed (example).
TRemove the milk pipe from the milk container or carton.
TFill a receptacle with 250 ml of fresh water.
TImmerse the milk pipe in the receptacle.
TPlace a receptacle under the fine foam frother.
nTTouch the Steam symbol.
HEATING / STEAM
As soon as the machine has heated up, STEAM / READY
appears, the light segment on the switch lights up.
hTTurn the switch to the mposition.
STEAM appears and the fine foam frother and the milk
pipe are rinsed with fresh water.
Rinsing the machine
Rinsing the fine foam
frother
Downloaded from ManualsNet.com search engine

3
IMPRESSA C50 – Quick Reference Guide
jTWhen clean water starts to flow out of the frother, turn the
switch back to the oposition.
STEAM / READY
The rinsing of the fine foam frother is now complete.
EThis chapter applies to the professional fine foam frother
and the fine foam frother.
To ensure that the fine foam frother always works properly, you
must clean it daily when you have been preparing milk. Your
IMPRESSA will not prompt you to clean the fine foam frother.
If the wrong cleaning agent is used, the machine could be damaged
and/or traces could be left behind in the water.
TUse only original JURA maintenance products.
EJURA Cappuccino Cleaner is available from specialised dealers.
Precondition: ESPRESSO is displayed (example).
TRemove the milk pipe from the milk container or carton.
TPour 250 ml of fresh water into a receptacle and add one
capful of Cappuccino Cleaner.
TImmerse the milk pipe in the receptacle.
TPlace a receptacle under the fine foam frother.
nTTouch the Steam symbol.
HEATING / STEAM
As soon as the machine has heated up, STEAM / READY
appears, the light segment on the switch lights up.
hTTurn the switch to the mposition.
STEAM appears and the fine foam frother and the milk
pipe are cleaned.
jTAs soon as the receptacle containing the cleaning solution is
empty, turn the switch to the oposition.
STEAM / READY
TRinse the receptacle thoroughly, fill it with 250 ml of fresh
water and immerse the milk pipe in the water.
TEmpty the other receptacle and place it under the fine foam
frother once more.
Cleaning the fine foam
frother
CAUTION
Downloaded from ManualsNet.com search engine

4
IMPRESSA C50 – Quick Reference Guide
hTTurn the switch to the mposition.
STEAM, the fine foam frother and the milk pipe are rinsed
with fresh water.
jTAs soon as the receptacle containing the fresh water is
empty, turn the switch to the oposition.
STEAM / READY
The cleaning of the fine foam frother is now complete.
To make sure the fine foam frother works properly, and in the inter-
ests of hygiene, it must be dismantled and rinsed daily if you have
been preparing milk. Your IMPRESSA will not prompt you to disman-
tle and rinse the frother.
TRemove the milk pipe and rinse it thoroughly under running
water.
TCarefully remove the fine foam frother from the Connector
System©by twisting slightly.
TDismantle the fine foam frother into its individual parts.
TRinse all the parts of the fine foam frother thoroughly under
running water. If there are severely dried-on milk residues,
firstly immerse the individual parts in JURA Cappuccino
Cleaner and then rinse them thoroughly.
TRe-assemble the fine foam frother.
EEnsure that all individual parts are correctly and firmly con-
nected to ensure optimum operation.
TFirmly attach the fine foam frother to the Connector Sys-
tem©.
To make sure the professional fine foam frother works properly, and
in the interests of hygiene, it must be dismantled and rinsed daily if
you have been preparing milk. Your IMPRESSA will not prompt you
to dismantle and rinse the frother.
TRemove the milk pipe and rinse it thoroughly under running
water.
TCarefully remove the professional fine foam frother from the
Connector System©by twisting slightly.
Dismantling and rinsing
the fine foam frother
Dismantling and rinsing
the professional fine
foam frother
Downloaded from ManualsNet.com search engine

5
IMPRESSA C50 – Quick Reference Guide
TDismantle the professional fine foam frother into its individ-
ual parts.
TRinse all the parts of the professional fine foam frother thor-
oughly under running water. If there are severely dried-on
milk residues, firstly immerse the individual parts in JURA
Cappuccino Cleaner and then rinse them thoroughly.
TRe-assemble the professional fine foam frother.
EEnsure that all individual parts are correctly and firmly con-
nected to ensure optimum operation.
TFirmly attach the professional fine foam frother to the Con-
nector System©.
Your IMPRESSA no longer has to be descaled if you are using the
CLARIS Blue filter cartridge. If you did not activate the filter cartridge
the first time you used the machine, you can do this now as follows.
EPerform the ‘inserting the filter’ operation without any inter-
ruptions. This will ensure that your IMPRESSA always produces
its best.
Precondition: ESPRESSO is displayed (example).
OTTouch the P symbol for approximately 2 seconds until
RINSE appears on the display.
gTTurn the Rotary Switch until FILTER- is displayed.
kTPress the Rotary Switch to enter the programme item.
NO
gTTurn the Rotary Switch until YES is displayed.
kTPress the Rotary Switch to confirm the setting.
OK appears briefly on the display.
FILTER INSERT, the Maintenance symbol clights up.
TRemove and empty the water tank.
TOpen the filter holder.
TRemove the CLARIS Blue filter cartridge from the Welcome
Pack.
Inserting and activating
the filter
Downloaded from ManualsNet.com search engine

6
IMPRESSA C50 – Quick Reference Guide
TInsert the CLARIS Blue filter cartridge into the water tank,
exerting slight pressure.
TClose the filter holder. It will click into place audibly.
EAfter two months, the filter will cease to work. Set the date on
the date plate on the filter holder in the water tank.
TFill the water tank with fresh, cold water and reinsert the
tank.
TPlace a receptacle (at least 500 ml) under the fine foam
frother.
cTTouch the Maintenance symbol.
SWITCH OPEN, the light segment on the switch lights up.
hTTurn the switch to the mposition.
FILTER RINSING, water flows out of the fine foam
frother.
EYou can interrupt rinsing of the filter at any time. To do this,
turn the switch clockwise. Turn the switch anticlockwise to
continue rinsing the filter.
EThe water may be slightly discoloured. This is not harmful to
health and does not affect the taste.
Rinsing of the filter stops automatically after approximately
500 ml. SWITCH CLOSE appears on the display.
jTTurn the switch to the oposition.
HEATING, the machine heats up.
ESPRESSO appears on the display (example). The filter is
now activated.
EAfter 50 litres of water have flowed through, the filter will
cease to work. Your IMPRESSA will automatically prompt you
to change the filter.
EAfter two months, the filter will cease to work. Set the date on
the date plate on the filter holder in the water tank.
EIf the CLARIS Blue filter cartridge is not activated in program-
ming mode, you will not be prompted to change the filter.
ECLARIS filter cartridges are available from specialised dealers.
Changing the filter
Downloaded from ManualsNet.com search engine

7
IMPRESSA C50 – Quick Reference Guide
Precondition: FILTER / ESPRESSO is displayed (example).
cTTouch the Maintenance symbol for approximately 2
seconds.
FILTER CHANGE appears on the display.
TRemove and empty the water tank.
TOpen the filter holder and remove the old CLARIS Blue filter
cartridge.
TInsert a new CLARIS filter cartridge Blue into the water tank,
exerting slight pressure.
TClose the filter holder. It will click into place audibly.
TFill the water tank with fresh, cold water and reinsert the
tank.
TPlace a receptacle (at least 500 ml) under the fine foam
frother.
cTTouch the Maintenance symbol.
SWITCH OPEN, the light segment on the switch lights up.
hTTurn the switch to the mposition.
FILTER RINSING, water flows out of the fine foam
frother.
EYou can interrupt rinsing of the filter at any time. To do this,
turn the switch clockwise. Turn the switch anticlockwise to
continue rinsing the filter.
EThe water may be slightly discoloured. This is not harmful to
health and does not affect the taste.
Rinsing of the filter stops automatically after approximately
500 ml. SWITCH CLOSE appears on the display.
jTTurn the switch to the oposition.
HEATING, the machine heats up.
ESPRESSO appears on the display (example).
Downloaded from ManualsNet.com search engine

8
IMPRESSA C50 – Quick Reference Guide
After 200 preparations or 80 switch-on rinses, the IMPRESSA will
prompt you to clean it.
If the wrong cleaning agent is used, the machine could be damaged
and/or traces could be left behind in the water.
TUse only original JURA maintenance products.
EThe cleaning programme lasts approximately 20 minutes.
EDo not interrupt the cleaning programme. The quality of
cleaning will be impaired if you do so.
EJURA cleaning tablets are available from specialised dealers.
Precondition: CLEAN / ESPRESSO is displayed (example).
cTTouch the Maintenance symbol for approximately 2
seconds.
EMPTY TRAY appears on the display.
TEmpty the drip tray and coffee grounds container and put
them back into the machine.
PRESS RINSE
TPlace a receptacle under the coffee spout.
cTTouch the Maintenance symbol.
CLEANING, water flows out of the coffee spout.
The operation is interrupted, ADD TABLET.
TOpen the cover of the filler funnel for ground coffee.
TInsert a JURA cleaning tablet into the filler funnel.
TClose the cover of the filler funnel.
cTTouch the Maintenance symbol.
CLEANING, water flows out of the coffee spout several
times.
The operation stops automatically.
EMPTY TRAY
TEmpty the drip tray and coffee grounds container and put
them back into the machine.
HEATING
ESPRESSO appears on the display (example). Cleaning is
now complete. Your IMPRESSA is once more ready for use.
Cleaning the machine
CAUTION
Downloaded from ManualsNet.com search engine

9
IMPRESSA C50 – Quick Reference Guide
The IMPRESSA builds up deposits of limescale over time and auto-
matically prompts you to descale it when necessary. The degree of
calcification depends on the hardness of your water.
If the descaling agent comes into contact with the skin or eyes, this
can cause irritation.
TAvoid contact with the skin or eyes.
TRinse off the descaling agent with clean water. Should you get
any descaling agent in your eye, see a doctor.
If the wrong descaling agent is used, the machine could be dam-
aged and/or traces could be left behind in the water.
TUse only original JURA maintenance products.
If the descaling operation is interrupted, there may be damage to
the machine.
TAllow the descaling programme to run to the end.
If the descaling agent comes into contact with sensitive surfaces
(e.g. marble), damage cannot be ruled out.
TClean up any splashes immediately.
EThe descaling programme lasts approximately 45 minutes.
EJURA descaling tablets are available from specialised dealers.
EIf you use a CLARIS Blue filter cartridge and this is activated,
you will not be prompted to descale.
Precondition: DESCALE / ESPRESSO is displayed (example).
cTTouch the Maintenance symbol for approximately 2
seconds.
EMPTY TRAY appears on the display.
TEmpty the drip tray and coffee grounds container and put
them back into the machine.
AGENT IN TANK
TRemove and empty the water tank.
TCompletely dissolve the contents of one blister (3 JURA des-
caling tablets) in a receptacle holding 500 ml of water. This
may take several minutes.
TPour the solution into the empty water tank and insert it into
the machine.
SWITCH OPEN, the light segment on the switch lights up.
Descaling the machine
JCAUTION
CAUTION
CAUTION
CAUTION
Downloaded from ManualsNet.com search engine

10
IMPRESSA C50 – Quick Reference Guide
TCarefully remove the fine foam frother from the Connector
System©by twisting slightly.
TPlace a receptacle (at least 500 ml) under the Connector Sys-
tem©.
hTTurn the switch to the mposition.
DESCALE, water flows out of the Connector System©sev-
eral times. The Maintenance symbol cflashes during the
descaling operation.
The operation is interrupted, SWITCH CLOSE.
jTTurn the switch to the oposition.
DESCALE, the descaling operation is continued.
The operation is interrupted, EMPTY TRAY.
TEmpty the drip tray and coffee grounds container and put
them back into the machine.
FILL TANK
TEmpty the receptacle and place it back under the Connector
System©.
TPlace another receptacle under the coffee spout.
TRemove the water tank and rinse it thoroughly.
TFill the water tank with fresh, cold water and reinsert the
tank.
SWITCH OPEN, the light segment on the switch lights up.
hTTurn the switch to the mposition.
DESCALE, the descaling operation is continued.
The operation is interrupted, SWITCH CLOSE.
jTTurn the switch to the oposition.
DESCALE, the descaling operation is continued.
The operation is interrupted, DESCALE.
Water flows out of the coffee spout.
EMPTY TRAY
TRe-assemble the fine foam frother.
TEmpty the drip tray and coffee grounds container and put
them back into the machine.
ESPRESSO appears on the display (example). Descaling is
now complete. Your IMPRESSA is once more ready for use.
EIf the descaling operation stops unexpectedly, rinse the water
tank thoroughly.
C50_Kurz/en/201211
Downloaded from ManualsNet.com search engine