Jura IMPRESSA F90 User manual

IMPRESSA F90/F9
Instructions for use
9/06
Art. Nr. 66379

Legend:
DISPLAY: serves as information.
DISPLAY: please follow the instructions shown.
= Note = Important = Tip
JURA Elektroapparate AG, CH-4626 Niederbuchsiten,
Internet http://www.jura.com

Fig. 1 Fig. 2 Fig. 3 Fig. 4
Fig. 11
Fig. 5 Fig. 6 Fig. 7 Fig. 8
Fig. 12Fig. 9 Fig. 10
Fig. 13 Fig. 14 Fig. 15 Fig. 16

Temp. max.
Fig. 17
Fig. 19
Fig. 18
Temp. min.

7
8
11
12
13
14/15
16
17
18
4
3
2
1
5
6
9
10
19
20
Control elements
A) Display dialog system
B) Symbols (navigation in programming mode)
) Large cup
D) offee
E) Espresso
F) Start (to start the draw-off operation)
G) offee strength «mild»
H) offee strength «Normal»
I) offee strength «strong»
1 Programming key
2 Selection key for pre-ground coffee
3 Draw-off key 1 cup
4 Draw-off key 2 cups
5 ON/OFF key
6 Maintenance key
7 onnectivity socket
8 ontrol panel
9 Filler funnel key for pre-ground coffee
10 Bean tank cover
11 Water tank with handle
12 Water portion draw-off key
13 Steam portion draw-off key
14 Professional appuccino Frother with milk pipe
15 Interchangeable hot water nozzle (see Fig. 7)
16 Height-adjustable coffee spout
17 up illumination (Fig. 10)
18 offee grounds container
19 Drip grate
20 Drip tray
21 Power switch
Sensitive Touch Screen TechnologyPROGRAMMATION
B)
8
A)
8
C) D) E) F) G) H) I)
21

6
Contents
1. Description of control panel ..............................page 7
2. Safety information ..........................................page 7
2.1 Warning.................................................page 7
2.2 Precautions .............................................page 7
2.3 Power Switch ..........................................page 8
3. Preparing the coffee machine for use...................page 8
3.1 Check the mains voltage.............................page 8
3.2 Check electrical fuse .................................page 8
3.3 Refill water.............................................page 8
3.4 Filling the bean tank .................................page 8
3.5 Adjusting the grinding gear.........................page 8
4. First use.......................................................page 8
4.1 Cup illumination.......................................page 9
5. Adjustment of water hardness ............................page 9
6. Installation of CLARIS plus filter cartridges .........page 10
6.1 Installing the filter....................................page 10
6.2 Replacing the filter ...................................page 10
7. Rinsing the coffee machine................................page 11
8. Drawing off coffee ..........................................page 11
8.1 Drawing off espresso .................................page 11
8.2 Drawing off a large cup of coffee .................page 12
8.3 Drawing off pre-ground coffee .....................page 12
9. Drawing off hot water...................................... page 12
10. Drawing off steam ..........................................page 13
11 Dispensing Cappuccino with the
Professional Cappuccino Frother ........................page 13
11.1 Dispensing Hot Milk with the
Professional Cappuccino Frother ...............page 14
11.2 Cleaning of the Professional Cappuccino
Frother ...............................................page 14
11.3 Rinsing the Professional Cappuccino
Frother ...............................................page 14
11.4 Cleaning the Professional-Cappuccino
Frother ...............................................page 14
12. Switching off the coffee machine ........................page 15
13. Programming ................................................page 15
13.1 Programming the filter ...........................page 16
13.2 Programming the water hardness...............page 16
13.3 Programming the aroma INTENSIVE
or STANDARD......................................page 16
13.4 Programming the temperature ..................page 16
13.5 Programming the water quantity ...............page 16
13.6 Programming 1 cup ...............................page 17
13.7 Programming the steam portion ................page 17
13.8 Programming the water portion ................page 18
13.9 Programming the time ............................page 18
13.10 Programming the automatic switch-on
time ...................................................page 18
13.11 Programming the automatic switch-off
time ...................................................page 19
13.12 Cup counter..........................................page 19
13.13 Programming the language ......................page 19
13.14 Connectivity .........................................page 20
14. Maintenance..................................................page 20
14.1 Refilling water ......................................page 20
14.2 Emptying the coffee grounds container........page 20
14.3 No Drip tray.........................................page 20
14.4 Filling the bean tank ..............................page 20
14.5 Replacing the filter ................................page 20
14.6 Cleaning the coffee machine .....................page 21
14.7 Coffee machine calcified ..........................page 21
14.8 General cleaning instructions ....................page 21
14.9 Emptying the system ..............................page 21
15. Cleaning .......................................................page 21
16. De-scaling.....................................................page 22
17. Disposal .......................................................page 23
18. Tips for perfect coffee......................................page 23
19. Messages ......................................................page 24
20. Problems ......................................................page 25
21. Legal information ...........................................page 26
22. Technical data ...............................................page 26

7
Important information
Thank you very much for purchasing this IMPRESSA coffee
machine.
Before using your new coffee machine for the first time, carefu y
read this operating manua and keep it for future reference.
Shou d you need more information or if you meet with particu ar
prob ems not specified in these operating instructions in sufficient
detai , either contact us direct y or contact your oca authorized
dea er.
You will also find useful tips on operation and maintenance
of your IMPRESSA on the website at www.jura.com.
Don’t forget to check out the Knowledge Builder our ani-
mated operating instructions. LEO, our assistant, will take
you through all the functions.
1. Description of control panel
A gent e push on the contro pane wi do, and the sensors wi
read your wish from your fingertips. The IMPRESSA offers Café à
a Carte, coffee to the taste of everybody. You can se ect one of the
programmed coffee specia ities at a gent e touch on the touch
screen.
As a resu t of high e ectromagnetic interference, the touch screen
may become inactive. All the remaining draw-off keys, the selec-
tion key for pre-ground coffee, draw-off key 1 cup, draw-off key 2
cups, can still be used.
2. Safety information
2.1 Warning
Chi dren do not rea ize the dangers invo ved in using e ectric
app iances, for this reason a ways keep an eye on chi dren when
they use e ectric app iances.
The coffee machine may on y be used by instructed persons.
Never use a defective coffee machine or a machine with a
defective mains cab e.
Never immerse the coffee machine in water.
Never repair or open the coffee machine yourse f. Any repairs
may on y be carried out by authorized service shops using ori-
gina spare parts and accessories.
2.2 Precautions
Never expose the coffee machine to weather (rain, snow, frost),
never touch the machine when your hands are wet.
Place the IMPRESSA on a firm, level base that is resistant to
any water that may leak. Never stand on hot or warm surfaces
(oven hobs). Keep out of the reach of children.
If you don’t use the machine for a onger time (ho idays, etc.)
a ways disconnect the mains cab e.
A ways disconnect mains cab e before c eaning the machine.
When disconnecting the mains cab e never pu on the mains
cab e or the machine itse f.
The coffee machine is connected to mains supp y via a mains
cab e. Make sure nobody can trip over the mains cab e. Make
sure chi dren and pets cannot reach the machine
Never put the coffee machine or individua parts of it into a
dishwasher.
Make sure to insta the machine at a p ace with sufficient air
circu ation, to prevent overheating of the machine.
E

8
2.3 Power switch
Actuate the power switch (21) on your IMPRESSA before
using the machine for the first time.
We recommend that you switch off your IMPRESSA with
the power switch (21) if you intend not to use the machine
for longer periods of time (e.g.during holidays)
3. Preparing the coffee machine for use
3.1 Check the mains voltage
The coffee machine is preset in the factory to the correct mains
vo tage. Check if your oca mains supp y vo tage comp ies with
the information given on the type p ate on the underside of the
coffee machine.
3.2 Check electrical fuse
The coffee machine is designed for an e ectric current of 10
Ampères. Check if the e ectrica fuse has sufficient capacity.
3.3 Refill water
On y use fresh, co d water. Never fi in mi k, minera water
or other iquids.
Take out the water tank and thorough y rinse it with co d tap
water (Fig. 1).
Then fi the water tank and re-insta it in the coffee machine.
Make sure the tank is insta ed correct y and that it engages
proper y.
3.4 Filling the bean tank
To ensure that your machine wi work perfect y for a ong
time and to avoid damage, p ease note that the grinding gear
of your JURA coffee machine is not suitab e for coffee beans
which were treated, during or after roasting, with additives
(e.g. sugar). Such coffee b ends may damage the grinding ge-
ar. Any repair costs resu ting from the use of such b ends are
not covered by warranty.
Open the cover of the bean tank (10).
Remove any dirt or foreign matter from the bean tank.
Fi coffee beans in the bean tank and c ose the cover.
3.5 Adjusting the grinding gear
You can adjust the grinding gear to the roast of your coffee. We
recommend that you use
a fine adjustment (the sma er the dots, the finer the
grinding is) for a ight roast
a coarse adjustment (the bigger the dots, the coarser the
grinding is) for a dark roast
The grinding degree may on y be adjusted whi e the grinding
gear is running.
Open the cover of the bean tank (10).
To adjust the grinding degree turn the rotary switch (Fig. 2) to
the required position.
4. First use
Fi coffee beans in the bean tank (10).
Fi water tank.
Switch on your coffee machine using the key .
WWW.IMPRESSA-F-LINE.COM

9
HELLO, MACHINE HEATING UP
FILL SYSTEM / WATER PORTION
Place a receptacle under the Professional Cappuccino Frother
(14) (Fig. 14).
Press water portion draw-off key
SYSTEM FILLING
MACHINE HEATING UP
PRESS MAINTENANCE
MACHINE RINSING
PLEASE SELECT
Press symbo .
COFFEE NORMAL
If FILL BEANS is disp ayed, touch the symbo
again. The mi was sti empty.
To get an exce ent crema, adjust the coffee spout (16) to the
size of your cup (Fig. 3 ).
4.1 Cup illumination
The cup i umination puts your coffee in a good ight, making it a
treat for the eyes.
When you p ug in or switch on the machine or press any key, the
cup i umination is activated for 1 minute. To switch on the cup
i umination, with the machine switched off, press any key (Fig. 10).
5. Adjustment of water hardness
In the coffee machine water is heated up. As a resu t, ca cifi-
cation occurs during norma use and is indicated auto-
matica y. Before using the machine for the first time the
hardness of the water used must be adjusted. Use the sup-
p ied test sticks for this.
1° German hardness is equiva ent to 1.79° French hardness.
The coffee machine has 5 hardness degrees which can be used and
are disp ayed whi e you are adjusting the water hardness.
The disp ayed information means the fo owing:
WATER
HARDNESS –– Water hardness function switched off
WATER German water hardness degree 1 to 7°
HARDNESS 1 French Water hardness degree 1.79 – 12.53°
WATER German water hardness degree 8 to 15°
HARDNESS 2 French Water hardness degree 14.32 – 26.85°
WATER German water hardness degree 16 to 23°
HARDNESS 3 French Water hardness degree 28.64 – 41.14°
WATER German water hardness degree 24 to 30°
HARDNESS 4 French Water hardness degree 42.96 – 53.7°
When the machine eaves the factory it is adjusted to WATER
HARDNESS 3. You can adjust another hardness. To do this,
proceed as fo ows:
Pu out the mains cab e from the cab e box on the rear side of the
coffee machine and connect the machine to mains supp y.
Press the key to switch on the coffee machine.
WWW.IMPRESSA-F-LINE.COM
Your coffee machine is switched to start-up position.
HELLO, MACHINE HEATING UP
PRESS MAINTENANCE
MACHINE RINSING
PLEASE SELECT
Press programming key unti you hear an acoustic signa .
FILTER NO
E

10
Press symbo unti the fo owing message is disp ayed:
WATER HARDNESS 3
Press symbo , you wi hear an acoustic signa and the
hardness degree f ashes.
Now, press symbo s to adjust the required hardness
degree.
Press symbo to confirm the new settings.
WATER HARDNESS 4
Press programming key to eave Programming Mode.
PLEASE SELECT
6. Installation of CLARIS plus filter cartridges
If the CLARIS p us fi ter cartridge is insta ed proper y, de-
sca ing of the coffee machine is no onger required. For
more information on the CLARIS p us fi ter cartridge refer
to brochure «CLARIS p us». Hard on imesca e. Gent e on
your coffee machine.»
6.1 Installing the filter
Use the key to switch on the coffee machine.
WWW. IMPRESSA-F-LINE.COM
HELLO, MACHINE HEATING UP
PRESS MAINTENANCE
MACHINE RINSING
PLEASE SELECT
Fo d up the cartridge ho der. Insert the fi ter cartridge in the
water tank (Fig. 4)
C ose the cartridge ho der unti it engages audib y.
Fi the water tank with co d, fresh tap water and insta it again.
Press Programming key unti you hear an acoustic signa .
NO FILTER
Press symbo , NO f ashes on the disp ay.
Press symbo unti the fo owing message is disp ayed:
FILTER YES (YES f ashes)
Press symbo .
INSTALL FILTER / WATER PORTION
Turn the selector switch of the Professional Cappuccino Frother
(14) to the steam position (Fig. 18).
Place a sufficiently large receptacle (at least 0.5 litre) under the
Professional Cappuccino Frother (14) and press the water portion
draw-off key .
FILTER RINSING. The water draw-off operation is
stopped automatica y.
MACHINE HEATING UP
PLEASE SELECT
Now you have activated the fi ter. In Programming Mode the
water hardness se ection function is no onger disp ayed.
6.2 Replacing the filter
After 50 litres of water the filter cartridge will need to be
replaced. The display will prompt you to change the filter.
Please monitor the period of use of the CLARIS plus filter
cartridge (max. 2 months) using the scale on the cartridge
holder by the water tank.
REPLACE FILTER / PLEASE SELECT
Use the key to switch off the coffee machine.
GOOD BYE
Press maintenance key for some seconds, with the machine
switched off.

11
INSTALL FILTER / WATER PORTION
Fo d up the cartridge ho der. Insert the fi ter cartridge in the
water tank (Fig. 4)
C ose the cartridge ho der unti it engages audib y.
Fi the water tank with co d, fresh tap water and reinsta it in
the coffee machine.
Turn the selector switch of the Professional Cappuccino Frother
(14) to the steam position (Fig. 18).
Place a sufficiently large receptacle (at least 0.5 litre) under
the Professional Cappuccino Frother (14) and press the draw-off
key .
FILTER RINSING. The water draw-off operation is
stopped automatica y.
MACHINE HEATING UP
PLEASE SELECT
7. Rinsing the coffee machine
When the coffee machine was switched off and has coo ed
down in the meantime, a rinsing operation is started when
the machine is switched on again. When the machine is
switched off, a rinsing operation is started automatica y.
Use the key to switch on the coffee machine.
WWW. IMPRESSA-F-LINE.COM
HELLO, MACHINE HEATING UP
PRESS MAINTENANCE
MACHINE RINSING
PLEASE SELECT
8. Drawing off coffee
You can change the se ected product at any time by pressing
the symbo s before starting the operation by pressing
. The se ected product is disp ayed.
Use the key to switch on the coffee machine.
WWW. IMPRESSA-F-LINE.COM
HELLO, MACHINE HEATING UP
PRESS MAINTENANCE
MACHINE RINSING
PLEASE SELECT
P ace 1 cup under the adjustab e coffee spout (16) and press
symbo .
COFFEE NORMAL
Press symbo s (/ / )to se ect the strength of your coffee.
COFFEE STRONG
Press symbo .
COFFEE STRONG Your product is being prepared.
PLEASE SELECT
8.1 Drawing off espresso
Use the key to switch on the coffee machine.
WWW. IMPRESSA-F-LINE.COM
HELLO, MACHINE HEATING UP
PRESS MAINTENANCE
MACHINE RINSING
PLEASE SELECT
P ace 1 cup under the adjustab e coffee spout (16) and press
symbo .
ESPRESSO NORMAL
E

12
Press (/ / )to se ect the strength of your espresso.
ESPRESSO STRONG
Press symbo .
ESPRESSO STRONG. Your product is being pre-
pared.
PLEASE SELECT
8.2 Drawing off a large cup of coffee
Use the key to switch on the coffee machine.
WWW. IMPRESSA-F-LINE.COM
HELLO, MACHINE HEATING UP
PRESS MAINTENANCE
MACHINE RINSING
PLEASE SELECT
P ace 1 cup under the adjustab e coffee spout (16) and press
symbo .
LARGE CUP NORMAL
Press (/ / )to se ect the strength of your coffee.
LARGE CUP MILD
Press symbo .
LARGE CUP MILD Your product is being prepared.
PLEASE SELECT
8.3 Drawing off pre-ground coffee
Never use instant coffee or quick-coffee. We recommend
that you a ways use powder from fresh coffee beans or, pre-
ground, vacuum-packed coffee. Never fi in more than 2
portions of powder. The pre-ground coffee tank is no storage
tank. Make sure that the pre-ground you use is not too fine.
This may cause b ocking of the system. In this case the
coffee on y drips out of the coffee spout.
If you press the draw-off key unintentiona y, you can stop
the operation by pressing the maintenance key. Your coffee
machine wi carry out a rinsing operation.
Use the key to switch on the coffee machine.
WWW. IMPRESSA-F-LINE.COM
HELLO, MACHINE HEATING UP
PRESS MAINTENANCE
MACHINE RINSING
PLEASE SELECT
Press se ection key .
FILL IN POWDER / PLEASE SELECT
Now fi in 1 or 2 eve dosing spoonfu s of pre-ground coffee in
the fi er funne for pre-ground coffee (Fig. 5).
P ace 1 cup under the adjustab e coffee spout (16) and press the
corresponding symbo ( / / ).
LARGE CUP POWDER
Press symbo .
LARGE CUP POWDER Your powder coffee is be-
ing prepared.
PLEASE SELECT
9. Drawing off hot water
You can adjust the water portion individua y (see Chapter
12 Programming). Insta the hot water jet (Fig. 7) to obtain
perfect water f ow.
At the start of the water draw-off there can be sp ashing
Avoid direct contact with the skin!
Do not rep ace the rep aceab e hot water jet direct y after
drawing off water, because the jet is hot after the draw-off
operation.

13
STEAM PORTION. Your product is being prepared.
PLEASE SELECT
You can also abort the dispensing, by pressing the steam
portion draw-off button early.
11. Dispensing Cappuccino with the
Professional Cappuccino Frother
Cappuccino comprises one third each of Espresso, hot milk
and milk foam. You produce the milk portion with the Pro-
fessional Cappuccino Frother (14).
When steam is drawn, a vacuum is produced which, with the
aid of the Professional Cappuccino Frother (14), draws in the
milk and produces milk foam.
To ensure perfect function, the Professional Cappuccino
Frother (14) must be cleaned regularly.
Make sure that the nozzle is correctly fitted. If the nozzle
becomes blocked with particles of milk residue or is incor-
rectly assembled, a danger can arise during use whereby the
nozzle may jump off.
When using for the first time, remove the protective cover from
the Professional Cappuccino Frother (14) (Fig. 9). The protective
cover is used only during transport as protection to prevent the
ingress of contaminated materials.
Remove the milk pipe from the Welcome Pack and connect it to
the Professional Cappuccino Frother (14).
Insert the other end of the milk pipe into a Tetra Pak of milk or
connect it to a milk container (Fig. 11).
Place a cup under the Professional Cappuccino Frother (14)
(Fig. 11).
P ace a cup under the hot water jet (15).
Press water draw-off key .
WATER PORTION
The programmed portion is being prepared. You can stop the
draw-off operation at any time by pressing the draw-off key .
PLEASE SELECT
10. Drawing off steam
The steam function is used for the preparation of milk foam
and hot milk, as well as for the Professional Cappuccino
Frother (14) cleaning programme.
With the optionally available 2-stage frothing nozzle, liquids
can be heated and frothed using the steam function.
Make sure that the nozzle is correctly fitted when drawing
steam. If the nozzle becomes blocked with particles of milk
residue or is incorrectly assembled, a danger can arise during
use whereby the nozzle may jump off.
Due to the system design, some water will escape at first
when steam is drawn. However, this will not affect the result
in any way.
When drawing steam, spluttering can occur at the start. The
nozzle becomes hot in use. Avoid any direct skin contact.
PLEASE SELECT
Press steam portion draw-off key .
MACHINE HEATING UP
PLEASE SELECT
Press steam draw-off key again.
E

14
A useful addition is available for all lovers of milk speciali-
ties in the form of high-quality vacuum milk containers.
They keep the milk cool the whole day long and are opti-
mally suited to the design of your IMPRESSA.
All original JURA accessories can be obtained from the
specialist shop.
Turn the selector switch of the Professional Cappuccino Frother
(14) to the milk foam position (Fig. 17).
PLEASE SELECT
Press the steam portion draw off key (13).
MACHINE HEATING UP
PLEASE SELECT
Press the steam portion draw off key (13) again.
STEAM PORTION
Preparation of milk foam will continue for the period you have
programmed for the steam portion. (See “Programming steam
portion” Chapter 13.7).
Adjust the steam dispensing time to suit the size of your cup.
You can also abort the dispensing, by pressing the steam
portion draw-off button early.
Now, move your cup with the milk foam and place it under the
coffee spout and dispense the required coffee product (Fig. 12).
Your Cappuccino is ready.
11.1 Dispensing Hot Milk with the
Professional Cappuccino Frother
Turn the selector switch of the Professional Cappuccino
Frother (14) to the milk range (Fig. 19).
The procedure for dispensing hot milk is the same as the
procedure for dispensing milk foam for Cappuccino (Chapter
11).
11.2 Cleaning of the
Professional Cappuccino Frother
To ensure that the Professional Cappuccino Frother functions
perfectly, you should rinse it with water each time after
preparing milk.
You will not be prompted by your IMPRESSA to rinse the
Professional Cappuccino Frother.
11.3 Rinsing the Professional Cappuccino Frother
Carefully pull off the Professional Cappuccino Frother from your
IMPRESSA.
Dismantle the Professional Cappuccino Frother (14) into its indi-
vidual parts (Fig. 15).
Thoroughly rinse all parts of the nozzle under running water.
Reassemble the Professional Cappuccino Frother (14) and refit it
on to your IMPRESSA.
11.4 Cleaning the Professional Cappuccino Frother
To ensure that the Professional Cappuccino Frother (14)
functions perfectly, you should clean it daily if you have pre-
pared milk foam or hot milk.
You will not be prompted by your IMPRESSA to clean the
Professional Cappuccino Frother (14).

15
You can obtain the JURA Auto-Cappuccino Cleaner from
the specialist shop.
Place a receptacle under the Professional Cappuccino Frother
(14) (Fig. 13).
Fill a second receptacle with 2.5 dl of fresh water and add one
capful of the Auto-Cappuccino Cleaner.
Dip the milk pipe into the second receptacle with the Auto-Cap-
puccino Cleaner. (Fig. 13)
Turn the selector switch of the Professional Cappuccino Frother
(14) to the milk position (Fig. 19) or to the milk foam position
(Fig. 17).
PLEASE SELECT
Press the steam portion draw off key (13).
MACHINE HEATING UP
PLEASE SELECT
Press the steam portion draw off key (13) again.
STEAM PORTION. Your product is being prepared.
Draw steam until the receptacle with the Auto-Cappuccino
Cleaner is empty.
This procedure cleans the Professional Cappuccino Frother and
the milk pipe.
Fill the receptacle with 2.5 dl of fresh water.
Dip the milk pipe into the receptacle with the fresh water.
Press steam portion draw-off key .
MACHINE HEATING UP
PLEASE SELECT
Press steam draw-off key again.
STEAM PORTION
Draw steam until the receptacle with the fresh water is empty.
This procedure rinses the Professional Cappuccino Frother (14)
and the milk pipe with fresh water.
Cleaning of the Professional Cappuccino Frother (14) is now
complete, your IMPRESSA is ready for use.
12. Switching off the coffee machine
To ensure perfect operation, please switch your IMPRESSA
to standby mode with the symbol first. Then switch the
machine off with the power switch (21).
Use the key to switch on the coffee machine.
PLEASE SELECT
Use key to switch OFF your coffee machine.
GOOD BYE
The automatic rinsing operation is started.
13. Programming
When your coffee machine eaves the factory it is adjusted such
that you can draw off coffee without having to change any settings.
However, you can programme various parameters individua y.
You can programme the fo owing stages:
Fi ter
Water hardness
Aroma
Temperature
Water quantity for coffee
1 Cup
Steam portion
Water portion
Time
Automatic switch-on time
Automatic switch-off time
Draw offs
Language
E

16
13.1 Programming the filter
Refer to Chapter 6.1 «Inserting the fi ter».
13.2 Programming the water hardness
Refer to Chapter 5 «Adjusting the water hardness».
13.3 Programming the aroma INTENSIVE or
STANDARD
The aroma for the powder quantities ( / / ) was
adjusted to Intensive in the factory. If requested it can a so
be set to Standard.
Use the key to switch on the coffee machine.
WWW. IMPRESSA-F-LINE.COM
HELLO, MACHINE HEATING UP
PRESS MAINTENANCE
MACHINE RINSING:
PLEASE SELECT
Press programming key unti you hear an acoustic signa .
Touch symbo unti the fo owing message is disp ayed:
AROMA INTENSIVE
Press symbo , you wi hear an acoustic signa , IN-
TENSIVE f ashes.
Use the symbo s to adjust the aroma to STANDARD.
Press symbo to confirm the new settings.
AROMA STANDARD
Use the symbo s to reach the next programming stage or
press programming key to quit Programming Mode.
13.4 Programming the temperature
Use the key to switch on the coffee machine.
WWW. IMPRESSA-F-LINE.COM
HELLO, MACHINE HEATING UP
PRESS MAINTENANCE
MACHINE RINSING
PLEASE SELECT
Press programming key unti you hear an acoustic signa .
Touch symbo unti the fo owing message is disp ayed:
TEMP. HIGH
Press symbo , you wi hear an acoustic signa and HIGH
f ashes.
Use the symbo to adjust the temperature to NORMAL.
Press symbo to confirm your settings.
TEMP. NORMAL
Use the symbo s to reach the next programming stage or
press programming key to quit Programming Mode.
13.5 Programming the water quantity
Use the key to switch on the coffee machine.
WWW. IMPRESSA-F-LINE.COM
HELLO, MACHINE HEATING UP
PRESS MAINTENANCE
MACHINE RINSING:
PLEASE SELECT
Press programming key unti you hear an acoustic signa .
Press symbo unti the fo owing message is disp ayed:
WATER QUANTITY
Press symbo .

17
SELECT PRODUCT
Se ect the product, the water quantity of which you want to
programme ( / / )
COFFEE 90 ML
Press symbo , the va ue f ashes.
Use symbo s to change the va ue in 5 m increments.
Press symbo to save the water quantity for this product.
WATER QUANTITY
Use the symbo s to reach the next programming stage
or press programming key to quit Programming Mode.
13.6 Programming 1 cup
Now, you wi program the draw-off key 1 cup (3). This has
no inf uence on the touch screen.
Use the key to switch on the coffee machine.
WWW. IMPRESSA-F-LINE.COM
HELLO, MACHINE HEATING UP
PRESS MAINTENANCE
MACHINE RINSING:
PLEASE SELECT
Press programming key unti you hear an acoustic signa .
Press symbo unti the fo owing message is disp ayed:
1 CUP 120 ML.
Press symbo , the va ue f ashes.
Use symbo s to change the va ue in 5 m increments.
Press symbo to save the water quantity for 1 cup.
1 CUP NORMAL
Press one of the symbo s ( / / ) to se ect the strength of
your coffee.
1 CUP STRONG
Press symbo to save the new settings.
1 CUP 180 ML (for examp e)
Use the symbo s to reach the next programming stage or
press key to quit Programming Mode.
These settings were taken over for the draw-off key for 2
cups.
13.7 Programming the steam portion
The programmab e steam portion time is between 3 and 60
seconds.
Use the key to switch on the coffee machine.
WWW. IMPRESSA-F-LINE.COM
HELLO, MACHINE HEATING UP
PRESS MAINTENANCE
MACHINE RINSING:
PLEASE SELECT
Press programming key unti you hear an acoustic signa .
Press symbo unti the fo owing message is disp ayed:
STEAM 20 SEC.
Press symbo , the va ue 20 f ashes.
Press symbo s to change the va ue.
Press symbo to save the new va ue.
STEAM 40 SEC (Examp e)
Use the symbo s to reach the next programming stage or
press programming key to quit Programming Mode.
E

18
13.8 Programming the water portion
Use the key to switch on the coffee machine.
WWW. IMPRESSA-F-LINE.COM
HELLO, MACHINE HEATING UP
PRESS MAINTENANCE
MACHINE RINSING
PLEASE SELECT
Press programming key unti you hear an acoustic signa .
Press symbo unti the fo owing message is disp ayed:
WATER PORTION
Press symbo , you wi hear an acoustic signa .
PRESS KEY
Press water portion draw-off key .
ENOUGH WATER? PRESS MAINTENANCE.
When the required water quantity is reached press key . The
water draw-off operation is stopped, the water portion is
programmed now.
Use the symbo s to reach the next programming stage or
press programming key to quit Programming Mode.
13.9 Programming the time
You must programme the time if you want to use the
automatic switch-on function.
Use the key to switch on the coffee machine.
WWW. IMPRESSA-F-LINE.COM
HELLO, MACHINE HEATING UP
PRESS MAINTENANCE
MACHINE RINSING:
PLEASE SELECT
Press programming key unti you hear an acoustic signa .
Press symbo unti the fo owing message is disp ayed:
TIME —:—
Press symbo , you wi hear an acoustic signa and —:—
f ashes.
Use symbo s to adjust the hours and confirm by pressing
.
Use symbo s to adjust the minutes and confirm by
pressing . The time is now programmed.
Use the symbo s to reach the next programming stage or
press programming key to quit Programming Mode.
If the machine is disconnected from mains supp y, the time
must be programmed again.
13.10 Programming the automatic switch-on time
You must programme the time (Chapter 13.9) if you want to
use the automatic switch-on function.
Use the key to switch on the coffee machine.
WWW. IMPRESSA-F-LINE.COM
HELLO, MACHINE HEATING UP
PRESS MAINTENANCE
MACHINE RINSING:
PLEASE SELECT
Press programming key unti you hear an acoustic signa .
Press symbo unti the fo owing message is disp ayed:
MACHINE ON —:—
Press symbo , you wi hear an acoustic signa and —:—
f ashes.

19
Use the symbo s to se ect the hours and confirm by
pressing .
Use symbo s to adjust the minutes and confirm by
pressing . The switch-on time is now programmed.
Use the symbo s to reach the next programming stage or
press programming key to quit Programming Mode.
13.11 Programming the automatic switch-off time
You can programme your coffee machine such that it wi
switch off automatica y after a certain time. You can
programme the switch-off time in a range between 0.5 and 9
hours, or se ect –:– (i.e. function switched off).
Use the key to switch on the coffee machine.
WWW. IMPRESSA-F-LINE.COM
HELLO, MACHINE HEATING UP
PRESS MAINTENANCE
MACHINE RINSING:
PLEASE SELECT
Press programming key unti you hear an acoustic signa .
Press symbo unti the fo owing message is disp ayed:
OFF AFTER 5.0 HOURS
Press symbo , you wi hear an acoustic signa and 5.0
f ashes.
Use the symbo s to se ect the hours and confirm by
pressing .
Use the symbo s to reach the next programming stage or
press programming key to quit Programming Mode.
13.12 Cup counter
This function is avai ab e with the fo owing products:
In Aroma Se ect via symbo s , , and via the pre-
ground coffee draw-off key , draw-off key for 1 cup
and draw-off key for 2 cups .
Use the key to switch on the coffee machine.
WWW. IMPRESSA-F-LINE.COM
HELLO, MACHINE HEATING UP
PRESS MAINTENANCE
MACHINE RINSING
PLEASE SELECT
Press programming key unti you hear an acoustic signa .
Press symbo unti the fo owing message is disp ayed:
DRAW OFFS ....... (Tota number of draw offs)
To earn how often a function was se ected, press the cor-
responding key or symbo .
Use the symbo s to reach the next programming stage or
press programming key to quit Programming Mode.
13.13 Programming the language
Use the key to switch on the coffee machine.
WWW. IMPRESSA-F-LINE.COM
HELLO, MACHINE HEATING UP
PRESS MAINTENANCE
MACHINE RINSING
PLEASE SELECT
Press programming key unti you hear an acoustic signa .
Press symbo unti the fo owing message is disp ayed:
SPRACHE DEUTSCH
E

20
Press symbo , you wi hear an acoustic signa and
DEUTSCH f ashes.
Press symbo s to se ect the required anguage.
Press symbo to save the new settings.
LANGUAGE ENGLISH
Use the symbo s to reach the next programming stage or press
programming key to quit Programming Mode.
13.14 Connectivity
With the Connectivity system it is possib e for your IMPRESSA
F90 to communicate with your PC and the Internet. To use this
feature, you wi need a kit which you can order at www.impressa-
f-Line.com or your oca authorized dea er. Avai ab e as an
optiona extra.
14. Maintenance
14.1 Refilling water
REFILL WATER
If this information is disp ayed, drawing off products is no
onger possib e. Refi water as described in Chapter 3.3.
PLEASE SELECT
The water tank shou d be rinsed dai y and refi ed with fresh
water. On y fi in fresh, co d water. Never fi in mi k,
minera water or other iquids.
14.2 Emptying the coffee grounds container
EMPTY COFFEE GROUNDS CONTAINER
If this information is disp ayed, drawing off products is no
onger possib e and the coffee grounds container must be
emptied (Fig.8 ).
Your coffee machine must be switched on.
Carefu y take out the drip tray, it is fi ed with water.
NO TRAY
PLEASE SELECT
The red water eve warning message appears when the
coffee drip tray is fu .
14.3 No Drip tray
NO TRAY
If this information is disp ayed, the drip tray is not insta ed
proper y or was not insta ed at a .
PLEASE SELECT
14.4 Filling the bean tank
REFILL BEANS
We recommend that you c ean the bean tank regu ar y before
refi ing beans, using a dry c oth. Before doing this, switch off
the coffee machine.
Refi beans as described in Chapter 3.4.
The message REFILL BEANS wi disappear after you draw
off your next cup of coffee.
14.5 Replacing the filter
After drawing off 50 iters the fi ter cartridge wi be used
up.
Refer to Chapter 6.2 «Rep acing the fi ter».
Other manuals for IMPRESSA F90
2
This manual suits for next models
1
Table of contents
Other Jura Coffee Maker manuals

Jura
Jura ENA 5 User manual

Jura
Jura ENA 4 User manual

Jura
Jura D4 User manual

Jura
Jura IMPRESSA F90 User manual

Jura
Jura E6 User manual

Jura
Jura IMPRESSA F50 Classic User manual

Jura
Jura IMPRESSA F70 User manual

Jura
Jura Impressa F9 guide User manual

Jura
Jura Giga X3 Professional Guide

Jura
Jura E8 User manual