Jura E6 User manual

E6/E60 – Quick Reference Guide

2
E6/E60 – Quick Reference Guide
E6/E60 – Quick Reference Guide
J
These short instructions do not replace the ‘E6/E60 Instructions for
Use’. Make sure you read and observe the safety information and
warnings first in order to avoid hazards.
You can start coffee system rinsing manually at any time.
Precondition: The start screen is displayed.
TPlace a receptacle under the coffee spout.
TPress the ‘ c’ button (white Maintenance symbol).
TPress the ‘Rinse the coffee system’ button to start the rinse
operation.
‘Machine is rinsing’, water flows out of the coffee spout. The
operation stops automatically. The start screen is displayed.
After each milk preparation, the JURA prompts you to perform a milk
system rinse.
Precondition: ‘Rinse the milk system’ is displayed.
TPlace a receptacle under the fine foam frother.
TPress the ‘ c’ button (red Maintenance symbol).
‘Switch open’
TTurn the switch to the xposition.
‘Milk system is being rinsed’appears and the fine foam fro-
ther is rinsed.
The rinse stops automatically. ‘Switch close’ appears on the
display.
TTurn the switch to the °position.
The start screen is displayed.
Rinsing the machine

3
E6/E60 – Quick Reference Guide
To ensure that the fine foam frother always works properly, you
must clean it daily when you have been preparing milk.
If the wrong cleaning agent is used, the machine could be damaged
and/or traces could be left behind in the water.
TUse only original JURA maintenance products.
EJURA milk system cleaner is available from specialised dealers.
Precondition: The start screen is displayed.
TPress the ‘P’button.
TPress the ‘Clean the milk system’ button.
‘Clean the milk system’
TPress the ‘Start’ button.
TPress the ‘Next’ button.
‘Clean the milk system’ / ‘Milk system cleaner’
TRemove the milk pipe from the milk container or carton.
TPour 250 ml of fresh water into a receptacle and add 1 capful
of milk system cleaner.
TImmerse the milk pipe in the receptacle.
TPlace a receptacle under the fine foam frother.
TPress the ‘Next’ button.
As soon as the machine has heated up, ‘Switch open’
appears.
TTurn the switch to the xposition.
‘Milk system is being cleaned’ appears and the fine foam fro-
ther and the milk pipe are cleaned.
‘Switch close’
TTurn the switch to the °position.
‘Clean the milk system’
TRinse the receptacle thoroughly, fill it with 250 ml of fresh
water and immerse the milk pipe in the water.
TEmpty the other receptacle and place it under the fine foam
frother once more.
TPress the ‘Next’ button.
‘Switch open’
TTurn the switch to the xposition.
Cleaning the fine foam
frother
CAUTION

4
E6/E60 – Quick Reference Guide
‘Milk system is being cleaned’ appears and the fine foam fro-
ther and the milk pipe are rinsed with fresh water.
‘Switch close’
TTurn the switch to the °position.
The start screen is displayed.
To make sure the fine foam frother works properly, and in the inte-
rests of hygiene, it must be dismantled and rinsed daily if you have
been preparing milk. Your JURA will not prompt you to dismantle
and rinse the frother.
TRemove the milk pipe and rinse it thoroughly under running
water.
TCarefully remove the fine foam frother from the Connector
System©by twisting slightly.
TDismantle the fine foam frother into its individual parts.
TRinse all the parts under running water. If there are severely
dried-on milk residues, firstly immerse the individual parts
in a solution of 250 ml cold water and 1 capful of JURA milk
system cleaner. Then rinse the parts thoroughly.
TRe-assemble the fine foam frother.
EEnsure that all individual parts are correctly and firmly
connected to ensure optimum operation.
TFirmly attach the fine foam frother to the Connector
System©.
Your JURA no longer has to be descaled if you are using the CLARIS
Smart filter cartridge. If you did not insert the filter cartridge the first
time you used the machine, you can do this now as follows.
Precondition: The start screen is displayed.
TRemove and empty the water tank.
TFit the filter cartridge extension supplied on top of a CLARIS
Smart filter cartridge.
Dismantling and rinsing
the fine foam frother
Inserting the filter

5
E6/E60 – Quick Reference Guide
TInsert the filter cartridge with its extension into the water
tank.
TTurn the filter cartridge clockwise until it audibly clicks into
place.
TFill the water tank with fresh, cold water and reinsert the
tank.
EThe machine automatically detects that you have just inserted
the filter cartridge.
‘Saved’ appears briefly on the display.
‘Switch open’
TPlace a receptacle (at least 300 ml) under the fine foam fro-
ther.
TTurn the switch to the xposition.
‘Filter is being rinsed’, water flows out of the fine foam fro-
ther.
Rinsing of the filter stops automatically after approximately
300 ml. ‘Switch close’ appears on the display.
TTurn the switch to the °position.
The start screen is displayed.
EIf the filter is active, this is indicated by a blue filter symbol at
the bottom of the display.
EOnce the filter cartridge stops working (depending on the
water hardness setting), the JURA will prompt you to change
the filter.
ECLARIS Smart filter cartridges are available from specialised
dealers.
Precondition: The start screen is displayed. The filter symbol at the
bottom of the display lights up red.
TRemove and empty the water tank.
TTurn the filter cartridge anticlockwise and remove it along
with the extension from the water tank.
Changing the filter

6
E6/E60 – Quick Reference Guide
TFit the filter cartridge extension on top of a new CLARIS
Smart filter cartridge.
TInsert the filter cartridge with its extension into the water
tank.
TTurn the filter cartridge clockwise until it audibly clicks into
place.
TFill the water tank with fresh, cold water and reinsert the
tank.
‘Saved’ appears briefly on the display. The machine has
automatically detected that you have just changed the filter
cartridge.
‘Switch open’
TPlace a receptacle (at least 300 ml) under the fine foam fro-
ther.
TTurn the switch to the xposition.
‘Filter is being rinsed’, water flows out of the fine foam fro-
ther.
EYou can interrupt rinsing of the filter at any time. To do this,
turn the switch clockwise. Turn the switch anticlockwise to
continue rinsing the filter.
EThe water may be slightly discoloured. This is not harmful to
health and does not affect the taste.
Rinsing of the filter stops automatically after approximately
300 ml. ‘Switch close’ appears on the display.
TTurn the switch to the °position.
The start screen is displayed.
The JURA builds up deposits of limescale over time and automati-
cally prompts you to descale it when necessary. The degree of calci-
fication depends on the hardness of your water.
EIf you are using a CLARIS Smart filter cartridge, you will not be
prompted to descale.
If the descaling agent comes into contact with the skin or eyes, this
can cause irritation.
TAvoid contact with the skin or eyes.
Descaling the machine
JCAUTION

7
E6/E60 – Quick Reference Guide
TRinse off the descaling agent with clean water. Should you get
any descaling agent in your eye, see a doctor.
If the wrong descaling agent is used, the machine could be dama-
ged and/or traces could be left behind in the water.
TUse only original JURA maintenance products.
If the descaling operation is interrupted, there may be damage to
the machine.
TAllow the descaling programme to run to the end.
If the descaling agent comes into contact with sensitive surfaces
(e.g. marble), damage cannot be ruled out.
TClean up any splashes immediately.
EThe descaling programme lasts approximately 40 minutes.
EJURA descaling tablets are available from specialised dealers.
Precondition: ‘Decalcify machine’ is displayed.
TPress the ‘ c’ button (red Maintenance symbol).
‘Descale’
TPress the ‘Start’ button.
TPress the ‘Next’ button.
‘Empty drip tray’
TEmpty the drip tray and coffee grounds container and put
them back into the machine.
‘Agent in tank’
TRemove and empty the water tank.
TCompletely dissolve the contents of one blister (3 JURA des-
caling tablets) in a receptacle holding 500 ml of lukewarm
water. This may take several minutes.
TPour the solution into the empty water tank and insert it into
the machine.
‘Switch open’
CAUTION
CAUTION
CAUTION

8
E6/E60 – Quick Reference Guide
TPlace a receptacle under the fine foam frother.
TTurn the switch to the xposition.
‘Machine is being descaled’ appears and water flows out of
the fine foam frother repeatedly.
The operation is interrupted, ‘Switch close’.
TTurn the switch to the °position.
‘Machine is being descaled’, the descaling operation is
continued.
The operation is interrupted, ‘Empty drip tray’.
TEmpty the drip tray and coffee grounds container and put
them back into the machine.
‘Fill water tank’
TEmpty the receptacle and place it under the fine foam fro-
ther and the coffee spout.
TRemove the water tank and rinse it thoroughly.
TFill the water tank with fresh, cold water and reinsert the
tank.
‘Switch open’
TTurn the switch to the xposition.
‘Machine is being descaled’, the descaling operation is con-
tinued.
The operation is interrupted, ‘Switch close’.
TTurn the switch to the °position.
‘Machine is being descaled’, the descaling operation is con-
tinued. Water flows out of the coffee spout.
The operation is interrupted ‘Empty drip tray’
TEmpty the drip tray and coffee grounds container and put
them back into the machine.
Descaling is now complete. The start screen is displayed.
EIf the descaling operation stops unexpectedly, rinse the water
tank thoroughly.