Jura IMPRESSA J9.3 One Touch TFT User manual

IMPRESSA J9.3 One Touch TFT –
Quick Reference Guide
The ‘IMPRESSA J9.3 One Touch TFT Instructions for Use’ together with
these short instructions ‘IMPRESSA J9.3 One Touch TFT – Quick Refer-
ence Guide’ has been awarded the seal of approval by the independent
German Technical Inspection Agency, TÜV SÜD, due to its easy-to-
understand style, its thoroughness and coverage of safety aspects.

2
IMPRESSA J9.3 One Touch TFT – Quick Reference Guide
IMPRESSA J9.3 One Touch TFT – Quick Reference Guide
J
These short instructions do not replace the ‘IMPRESSA J9.3 One
TouchTFTInstructionsforUse’.Makesureyoureadandobservethe
safety information and warnings first in order to avoid hazards.
You can initiate the rinse operation manually at any time.
Precondition: ‘Please select product:’ is displayed.
TPlace a receptacle under the coffee spout.
OTPress the P button.
‘Maintenance status (1/6)’
TPress the ‘Switch-on rinse’ button.
‘Machine is rinsing.’, water flows out of the coffee spout.
The rinse stops automatically and ‘Please select product:’
appears on the display.
Aftereachmilkpreparation,theIMPRESSApromptsyoutorinsethe
milk system.
Precondition: ‘Rinse the milk system’ is displayed.
TPlace a receptacle under the cappuccino frother.
cTPress the Rotary Switch.
‘Milksystemis beingrinsed.’, waterflowsoutofthecappuc-
cino frother.
The rinse stops automatically and ‘Please select product:’
appears on the display.
To ensure that the cappuccino frother always works properly, you
should clean it daily when you have been preparing milk. Your
IMPRESSA will not prompt you to clean the cappuccino frother.
Ifthe wrongcleaningagentis used,the machinecouldbedamaged
and/or traces could be left behind in the water.
TUse only original JURA maintenance products.
EJURA Cappuccino Cleaner is available from stockists.
Rinsing the machine
Rinsing the cappuccino
frother
Cleaning the cappuccino
frother
CAUTION

3
IMPRESSA J9.3 One Touch TFT – Quick Reference Guide
Precondition: ‘Please select product:’ is displayed.
OTPress the P button.
‘Maintenance status (1/6)’
TPress the ‘Clean the milk system’ button.
‘Cleaning agent for milk system’
TPour 250 ml of fresh water into a receptacle and add one
capful (max. 15 ml) of Cappuccino Cleaner.
TImmerse the milk pipe in the receptacle.
TTurn the setting wheel of the cappuccino frother to the Milk
Foam üor Milk zposition.
TPlace another receptacle under the cappuccino frother.
TPress the ‘Next’ button.
‘Milk system is being cleaned.’, water flows out of the cap-
puccino frother.
‘Water for cleaning milk system’
TRinse the receptacle thoroughly, fill it with 250 ml of fresh
water and immerse the milk pipe in the water.
TEmpty the other receptacle and place it under the cappuc-
cino frother again.
cTPress the Maintenance button.
TPress the ‘Next’ button.
‘Milk system is being cleaned.’, the cappuccino frother and
the pipe are rinsed with fresh water.
‘Please select product:’ appears on the display.
TCarefully pull the cappuccino frother down and off.
TDismantle the cappuccino frother into its individual parts.
TRinse all parts of the cappuccino frother thoroughly under
running water.
TReassemble the cappuccino frother.
EEnsure that all individual parts are correctly and firmly con-
nected to ensure correct operation of the cappuccino frother.
TFirmly attach it to the connector.
Dismantling and rinsing
the cappuccino frother

4
IMPRESSA J9.3 One Touch TFT – Quick Reference Guide
Your IMPRESSA no longer has to be descaled if you are using the
CLARIS Blue filter cartridge.If the water hardness is 10° dH or more,
we recommend using the filter cartridge.
EIf you do not know the hardness of your water, you must find
this out first .
EPerform the ‘inserting the filter’ operation without any inter-
ruptions.ThiswillensurethatyourIMPRESSAalwaysproduces
its best.
Precondition: ‘Please select product:’ is displayed.
OTPress the P button.
‘Maintenance status (1/6)’
gTTurn the Rotary Switch until the programme item ‘Mainte-
nance settings (3/6)’ is displayed.
TPress the ‘Filter’ button.
‘Filter’
TPress the ‘Active’ button.
TPress the ‘Save’ button.
‘Saved’ appears briefly on the display.
‘Insert filter’.
TRemove the filter cartridge extension from the Welcome
Pack.
TFitthefilterextensionontopofaCLARISBluefiltercartridge.
TRemove and empty the water tank.
TOpen the filter holder and insert the filter cartridge into the
water tank, exerting slight pressure.
TClose the filter holder. It will click into place audibly.
EAfter twomonths,thefilterwill ceasetowork.Set thedateon
the date plate on the filter holder in the water tank.
TFill the water tank with fresh, cold water and reinsert the
tank.
TPlace a receptacle (at least 500 ml) under the cappuccino
frother.
TPress the ‘Next’ button.
‘Filter is being rinsed.’, water flows out of the cappuccino
frother.
Inserting and activating
the filter

5
IMPRESSA J9.3 One Touch TFT – Quick Reference Guide
EYou can interrupt rinsing of the filter at any time by pressing
any button. Press the Rotary Switch kto continue rinsing of
the filter.
EThe water may be slightly discoloured. This is not harmful to
health and does not affect the taste.
Rinsing of the filter stops automatically after approximately
500 ml. The machine heats up. ‘Please select product:’
appears on the display. The filter is now activated.
EAfter 50 litres of water have flowed through, the filter will
cease to work. Your IMPRESSA will automatically prompt you
to change the filter.
EAfter twomonths,thefilterwill ceasetowork.Set thedateon
the date plate on the filter holder in the water tank.
EIf the CLARIS Blue filter cartridge is not activated in program-
ming mode, you will not be prompted to change the filter.
Precondition: ‘Change filter’ is displayed.
OTPress the P button.
‘Maintenance status (1/6)’
TPress the ‘Change the filter’ button.
‘Change the filter’
EIf you do not want to start changing the filter just yet, press
the ‘’button. The prompt ‘Change filter’ remains active.
TPress the ‘Next’ button.
‘Change filter’
TRemove and empty the water tank.
TOpen the filter holder and remove the old CLARIS Blue filter
cartridge and filter extension.
TFit the filter extension on top of a new filter cartridge.
TInsert the filter cartridge into the water tank, exerting slight
pressure.
TClose the filter holder. It will click into place audibly.
TFill the water tank with fresh, cold water and reinsert the
tank.
Changing the filter

6
IMPRESSA J9.3 One Touch TFT – Quick Reference Guide
TPlace a receptacle (at least 500 ml) under the cappuccino
frother.
TTurn the setting wheel of the cappuccino frother to the
Steam position n.
TPress the ‘Next’ button.
‘Filter is being rinsed.’, water flows out of the cappuccino
frother.
EYou can interrupt rinsing of the filter at any time by pressing
any button. Press the Rotary Switch kto continue rinsing of
the filter.
EThe water may be slightly discoloured. This is not harmful to
health and does not affect the taste.
Rinsing of the filter stops automatically after approximately
500 ml. The machine heats up. ‘Please select product:’
appears on the display.
After 200 preparations or 80 switch-on rinses, the IMPRESSA will
prompt you to clean it.
Ifthe wrongcleaningagentis used,the machinecouldbedamaged
and/or traces could be left behind in the water.
TUse only original JURA maintenance products.
EThe cleaning programme lasts approximately 20 minutes.
EDo not interrupt the cleaning programme. The quality of
cleaning will be impaired if you do so.
EJURA cleaning tablets are available from stockists.
Precondition: ‘Clean machine’ is displayed.
OTPress the P button.
‘Maintenance status (1/6)’
TPress the ‘Clean’ button.
‘Clean’
EIf you do not want to start cleaning just yet, press the ‘’but-
ton. The prompt ‘Clean machine’ remains active.
TPress the ‘Next’ button.
‘Empty coffee grounds container’
Cleaning the machine
CAUTION

7
IMPRESSA J9.3 One Touch TFT – Quick Reference Guide
TEmpty the drip tray and coffee grounds container and put
them back into the machine.
‘Please press the Rotary Switch.’.
TPlace one receptacle under the coffee spout and another
under the cappuccino frother.
kTPress the Rotary Switch.
‘Machine is being cleaned.’, water flows out of the coffee
spout.
The operation is interrupted, ‘Add cleaning tablet’.
TOpen the cover of the filler funnel for ground coffee.
TInsert a JURA cleaning tablet into the filler funnel.
TClose the cover of the filler funnel.
‘Please press the Rotary Switch.’.
kTPress the Rotary Switch.
‘Machine is being cleaned.’, water flows repeatedly out of
the coffee spout and the cappuccino frother.
The operation is interrupted, ‘Empty coffee grounds contai-
ner’.
TEmpty the drip tray and coffee grounds container and put
them back into the machine.
Cleaning is now complete. The IMPRESSA is once more
ready for use.
The IMPRESSA builds up deposits of limescale over time and auto-
matically prompts you to descale it when necessary. The degree of
calcification depends on the hardness of your water.
If the descaling agent comes into contact with the skin or eyes, this
can cause irritation.
TAvoid contact with the skin or eyes.
TRinseoffdescalingagentwithcleanwater.Shouldyougetany
descaling agent in your eye, see a doctor.
If the wrong descaling agent is used, the machine could be dam-
aged and/or traces could be left behind in the water.
TUse only original JURA maintenance products.
If the descaling operation is interrupted, there may be damage to
the machine.
TAllow the descaling programme to run to the end.
Descaling the machine
JCAUTION
CAUTION
CAUTION

8
IMPRESSA J9.3 One Touch TFT – Quick Reference Guide
If the descaling agent comes into contact with sensitive surfaces
(e.g. marble), damage cannot be ruled out.
TClean up any splashes immediately.
EThe descaling programme lasts approximately 45 minutes.
EJURA descaling tablets are available from stockists.
EIf you use a CLARIS Blue filter cartridge and this is activated,
you will not be prompted to descale.
Precondition: ‘Decalcify machine’ is displayed.
OTPress the P button.
‘Maintenance status (1/6)’
TPress the ‘Descale’ button.
‘Descale’
EIfyoudonotwanttostartdescalingjustyet,pressthe‘’but-
ton. The prompt ‘Decalcify machine’ remains active.
TPress the ‘Next’ button.
‘Empty drip tray’
TEmpty the drip tray and coffee grounds container and put
them back into the machine.
‘Pour descaling agent into water tank’.
TRemove and empty the water tank.
TCompletely dissolve the contents of one blister (three JURA
descaling tablets) in a receptacle holding 500 ml of water.
This may take several minutes.
TPourthesolutionintotheemptywatertankandinsertitinto
the machine.
‘Please press the Rotary Switch.’
TRemove the cappuccino frother.
TPlace a receptacle (at least 500 ml) under the connector of
the cappuccino frother.
kTPress the Rotary Switch.
‘Machine is being descaled.’, water flows repeatedly out of
the connector of the cappuccino frother.
The operation stops automatically, ‘Empty drip tray’.
CAUTION

9
IMPRESSA J9.3 One Touch TFT – Quick Reference Guide
TEmpty the receptacle under the connector of the cappuc-
cino frother.
TEmpty the drip tray and coffee grounds container and put
them back into the machine.
‘Fill water tank’
TRemove the water tank and rinse it thoroughly.
TFill the water tank with fresh, cold water and reinsert the
tank.
‘Please press the Rotary Switch.’
TRefit the cappuccino frother.
TPlaceareceptacleunderthecappuccinofrotherandanother
under the coffee spout.
kTPress the Rotary Switch.
‘Machine is being descaled.’, water flows out of the cappuc-
cino frother and the coffee spout.
‘Machineisheating.’,‘Machineisrinsing.’,waterflowsoutof
the coffee spout.
The operation stops automatically, ‘Empty drip tray’.
TEmpty the drip tray and coffee grounds container and put
them back into the machine.
Descaling is now complete. The IMPRESSA is once more
ready for use.
EIf the descaling operation stops unexpectedly, rinse the water
tank thoroughly.
J9.3_Kurz/en/201101