JVC XS-N1129AA User manual

Register your product at jvctv.com.au/warranty-registration
5
Waterproof Bluetooth Speaker
XS-N1129AA/XS-N1129DA/XS-N1129GA
User Manual
Using the Hands-Free Function
When a smartphone is connected to your speaker follow the steps
below to take calls hands-free.
1. Press“ ”to pick up the call.
2. Press and hold“ ”for 2 sec to reject the call.
3. During a call: Press“ ”again to hang up the call.
Troubleshooting
The speaker doesn’t connect
to device Speaker needs to be connected/re-paired to
device
A tone is heard every few
seconds
Speaker needs to be charged
The speaker will not power on Speaker needs to be charged
The speaker sound distorts at
high volume. The device's volume needs to be lowered
Bluetooth connection does
not work up to 10 metres.
Avoid operating the wireless speaker in areas
of strong electromagnetic interference,such
as near induction cookers, large power fans,
motors, etc.
Move the speaker closer to your
Bluetooth-enabled device.
Fully charge the speaker and try again.
Problem Solution

21 3 4
Introduction
Use the JVC Waterproof Bluetooth Speaker paired with smartphones,
tablets, or other devices to stream music and enjoy hands-free
phone calls. For best results, please read this user manual carefully
before first use.
Specifications
Loudspeaker: 4Ω 5W
Built-in Battery:Li-ion 600mAh
Dimensions: 102x93x43 mm
SNR:80± 3dB
Bluetooth distance: up to 10m
Charging Time: 2-3 hours
Weight: 160 g
Speaker Diameter: 45 mm
Charging: DC5 V, 500mA
Important Waterproof/Safety Information
This speaker is IP67 rated. This means that the speaker can be
submerged under water (up to 1 metre depth) for short periods of
time (up to 30 minutes).
The charging port must be securely closed before using the
speaker in a wet environment.
Make sure the speaker is completely dry before connecting the
charging cable.
Package Contents
1. Bluetooth Speaker 2. USB Charging Cable 3. User Manual
Important Safety Precautions
1. Keep this product and its charging cable away from excessive
heat.
2. Do not operate this device with a damaged cable or after it
has malfunctioned or has been damaged in any manner.
3. Do not disassemble your device No user-serviceable parts
inside.
4. This product is not a toy. Children should be supervised to
ensure that they do not play with the appliance.
5. Do not expose batteries to heat or fire as they may explode.
6. Do not dispose of batteries in your household waste. Contact
your local council for information on disposal or recycling.
Please read all instructions carefully and retain for future reference.
When using the unit, basic safety precautions should always be
followed, including the following:
Charging Your Speaker
1. Connect one end of the included USB Charging Cable to the
Charging Port on your speaker. Then plug the other end of the
USB Charging Cable into a suitable USB port on your computer
to recharge your speaker’s internal rechargeable battery.
Please note: The internal battery of your speaker takes
approximately two hours to charge when completely drained.
2. When charging, a red LED light will illuminate to indicate that
the unit is charging. The red light will turn off when your unit is fully
charged.
A Quick Look at Your Device
4
1. Previous: Press and hold to access the
last track in a playlist.Press to lower the volume.
2. Phone: Press this button to activate
the speaker phone function. When music is
playing, press to play or pause a track.
3. Next: Press and hold to access the next
track in a playlist.Press to increase the volume.
4. Charging Port
You can plug one end of the included USB Charging
Cable into this jack, while plugging the other end into
a USB port on your computer in order to charge your
speaker’s built in lithium battery.
You can also use a suitable USB adaptor for charging.
Important: Make sure the unit is completely dry before
charging.
5. ON/OFF Switch
Press and hold the“ ”to switch the unit on.
Press and hold the“ ”again to switch the unit off.
1 3
2
5
Pairing Bluetooth-enabled devices to Your Speaker
In order to pair your Bluetooth device (smartphone/tablet etc.) to
your Speaker for the first time, follow the steps below:
1) Make sure the wireless audio source is held within three metres
of your speaker.
2) Press and hold the “ ” switch on your speaker to power on.
The LED light will blink blue to indicate that you have entered
pairing status.
3) Go to the setting menu of your wireless audio source. Please
refer to the user manual of your wireless audio source for more
information.
4) Search the devices and select “XS-N1129”.
5) Once paired, the blue LED light will be solid and you can use
your speaker to listen to audio from your wireless sound source.
Understanding the LED Status Lights
When Charging Your Speaker
Solid red LED = Charging
No red LED = Charge is complete
When Pairing Your Speaker to a Bluetooth-enabled
device
Rapid blinking blue LED: Not connected (ready to pair)
Solid blue LED: Connected