JWA 68556 User manual

1
A
DRESSER
SSEMBLY INSTRUCTION
Imported by JWA Furniture Pty Ltd, Qld, Brisbane Australia.
For any assistance with assembly or for missing parts please refer to your receipt
1200MM
450MM
735MM
ITEM CODE 68556

Allow 30 min For 1 person AddiƟonal tools required
PRE-ASSEMBLY PREPARATION
Before you start:
1. Choose a clean, level, spacious assembly area. Avoid hard surfaces that may
damage the product
2. Take care when liŌing. Product should be assembled as near as possible to the
point of use
3. Ensure that you have all required contents for complete assembly
4. Always read the assembly instrucƟons carefully before beginning assembly.
5. Keep all hardware parts and packaging out of reach of small children.
6. Do not over Ɵghten the screws and bolts as this may damage the threads
7. Assembly is to be carried out by a competent adult(s) ONLY
8. During assembly, children should be kept away from the product due to possible
risk to injury.
9. Do not use this item if any components are missing or damaged.
10. Please keep the instrucƟons for future reference.
2

3
X6


















24pcs
M6X39mm
12pcs
M5X40mm
PARTS LIST
B
24pcs
M15X12mm
C
26pcs
M8X30mm
D
24pc
M3.5X14mm
12pcs
F
12pcs
M5X50mm
G
4pcs
M3X14mm
M4X19mm
16pcs
J
A
E
I
M3X12mm
H
20pcs
LEFT PANEL
2pcs
K
1
RIGHTT PANEL
2
MIDDLE PANEL
3
LEFT PANEL
4
BOTTOM PANEL
5
TOP PANEL
6
BACK PANEL
7
DRAWER SIDE
8
DRAWER SIDE
9
DRAWER BACK
10
DRAWER BASE
11
DRAWER FRONT
DRAWER FRONT
DRAWER FRONT
DRAWER FRONT
DRAWER FRONT
DRAWER FRONT
12
13
14
15
16
17
1pc
L

4
CAM LOCK INSTALL METHOD AS FOLLOWS
Step 1 Step 2
OR
Step 3
Fix cam nut into
the bottom of hole
then tighten it.
Lock
1.1cm
A

5



D
D
F
F
F
F
F
F
F
D
D
D
STEP 1

6
F
D
D
D
F
F
F
F

STEP 2

7
C
E
A
A




STEP 3
STEP 4

8
C
C
B
B
A
A





STEP 5
STEP 6

9
C
C
E
E
B
B
C1
A1
B1
E1
G
H
L
K
H
C1
A1
B1
E1
STEP 7
STEP 8

10
A
A
A
B
B
B
C
C
C





STEP 9
STEP 10

11
J
J
J
E
E
C
C









STEP 12
STEP 11
X6


L

12
A
A
A
A
A
L1
M1
N1
O1
P1
Q1
B
B
B
B
C
C
C
C

















STEP 14
STEP 13

13
B
B
B
B
C
C
C
C
B
B
B
B
C
C
C
C




STEP 16
STEP 15

14
I
I
I
I
I
I






STEP 17
ASSEMBLY COMPLETE

15
SAFETY BRACKETS
INSTRUCTIONS
1. Attach one Mounting Plate to the wall with the Large Screws. Make sure to
attach the Mounting Plate into a stud. If mounting into brick or masonry you
will need to acquire wall anchors.
2. Attach the second Mounting Plate to the furniture frame with the Short
Screws.
3. Move the furniture to its final position. Thread a Wall Strap through the both
Mounting Plates and tighten until snug. Do not over tighten.
4. Make sure that the Mounting Plates are firmly attached to the wall and
furniture and that the Wall Strap is snug.
J
.'8*='8+
=GRR
(GIQYOJK
2GXMK9IXK]^=GRR9ZXGV^3U[TZOTM6RGZK^ 9SGRR9IXK]^
^

16
To protect your furniture, we suggest the following:
Avoid placing your furniture in direct sunlight.
Do not place furniture directly under windows.
Do not place sharp materials (knife, fork, etc.) directly onto
your furniture as sharp material may scrape and damage the
¿nish.
Do not place material with high temperature directly onto the
surface of your furniture.
Clean up spills quickly. Water left over a prolonged period of
time may cause damage. Alcohol, perfume, nail polishes,
aftershave and some medication may cause severe ¿nish
damage if not cleaned immediately.
Use a clean, soft, dry, lint free absorbent cloth to clean your
furniture. Do not use any detergent as they may contain
ingredients that may react and damage the ¿nish.
NOTE: If the above care advise is not adhered to your product
warranty may become void