JWA BURGESS 76427 User manual

Imported by JWA Furniture Pty Ltd, Qld, Brisbane Australia.
For any assistance with assembly or for missing parts please refer to your receipt
ASSEMBLY INSTRUCTION
1
800MM
400MM
1100MM
76427
4 DRAWER TALL CHEST
BURGESS
ITEM CODE

PRE-ASSEMBLY PREPARATION
Before you start:
1.Choose a clean, level, spacious assembly area. Avoid hard surfaces that may damage the
product
2.Take care when lig. Product should be assembled as near as possible to the point of
use
3.Ensure that you have all required contents for complete assembly
4.Always read the assembly instrucns carefully before beginning assembly.
5.Keep all hardware parts and packaging out of reach of small children.
6.Do not over hten the screws and bolts as this may damage the threads
Allow 1 hour For 2 person Addinal tools required
2

PARTS LIST
3
1
10
23
4
5
5
6
7
8
9
11
11
12
12
13
14
15
16
17
16
16 X4

4
NO. ITEM QTY NO. ITEM QTY
PARTS LIST
A30PCS
B30PCS
C22PCS
D8PCS
E2PCS
F24PCS
8PCS
M
4PCS
N
Φ6*35
Φ15*10
Φ6*30
Φ4*50
G16PCS
Φ3*12
Φ3*16
P
8PCS
OΦ4*14 48PCS
Φ4*35
Φ6*60
16PCS
H
8PCS
I
1PC
K
8PCS
L
4PCS
Q
48PCS
R
S2 S1 8PCS
S

5
NO. ITEM QTY NO. ITEM QTY
1TOP PANEL 1 PC
3
1 PC
1 PC
41 PC
52 PCE
4 PCE
4 PCE
4 PCE
PARTS LIST
210
64 PCE
74 PCE
4 PCE
2 PCE
11
12
LEFT SIDE PANEL
RIGHT SIDE PANEL
BOTTOM PANEL
BACK PANEL
DRAWER FRONT PANEL
DRAWER LEFT SIDE PANEL
8DRAWER RIGHT SIDE PANEL
DRAWER BACK PANEL
DRAWER BOTTOM PANEL
LEGS SUPPORT PANEL
1 PC
13 LEGS SUPPORT PANEL
1 PC
14 LEGS SUPPORT PANEL
9
LEG
4 PCE
15 DRAWER SUPPORT PANEL
3 PCE
16 CROSSING BAR
1 PC
17 MIDDLE SUPPORT PANEL

STEP 1:
STEP 2:
6
O X8
1
A
I X4A X2
I
O
O X8I X4A X2
4
I
I
I
O
O
O
A
I
O
I
I
I
O
O
O

STEP 3:
STEP 4:
7
S X4
2
S1
R X12
S1
S1
S1
S1
RRR
R R R
RR R
RRR
RRR
S X4
R X12
3
S1
S1
S1
S1
S1
RRR
RR
RR
RR
RRR

STEP 5:
STEP 6:
8
A X6
2
A
C X6
3A
A
A
A
A
B X6
32
16
16
16
B
B
B
B
B
B
C
C
CC
C
C

STEP 7:
STEP 8:
9
O X8
2
B X2
3
4
O
2
3
4
17
B
OO
O

STEP 9:
STEP 10:
10
2
O X8
3
4
55
4
2
3
1
OO
O

STEP 11:
STEP 12:
11
B X2
2
B
3
4
1
C X4D X4
4
3
2
13
14
CC
CC
DD
DD

4
STEP 13:
STEP 14:
12
4D
O X16
C X4
D X4
3
2
12
12
D
C
C
C
C
D
D
P X4
4
3
2
P
P
P
P
O
O
O
O

STEP 15:
STEP 16:
13
K
3
N X8
L X8
M X8
K X1
2
11
11
11
11
4
M
MM
M
L
L
L
L
N
N
N
N
A X20B X20C X8F X24Q X4 X4
6
7
7
7
88
8
9
9
10
15
AAA
B
B
B
F
FF
Q
Q
C
C

STEP 17:
STEP 18:
14
S X8
6
S2
X4
R X24
7
S2
RRR
RR
To insert Drawers:
a) Bring the ball-bearing slider on Drawer Glide Track(S1) forward to the front edge of(S1).
b) Align the back open-end of the Drawer Glide Runner(S2) on each side of the drawer to fit
squarely into the groove on the open front-end of(S1).Be sure the drawer/M2 is not tilted or
angled, and gently push in drawer squarely.
c) When the drawer is pushed in about half way,the Disconnect Lever on (S2) will be engaged
onto(S1) which will create a slight resistance-this is normal. Pull out the drawer a little bit and
gently push in the drawer again to engage the Lever to the slide mechanism on (S1).
The drawer should now slide smoothly.
d) If the drawer cannot be pushed in or stuck, do not force it in. Remove the drawer and
repeat the steps above.
S2
S1
6
6
6
6

STEP 19:
STEP 20:
15
G X16
2
H
E X2
H X16
12
5
5
H
HH
H
H
H
H
HH HH
HHHH
H
H
G
GGGG
GGGG
GG
GG
GGG G
E
E
E
EE
WALL E

ASSEMBLY IS COMPLETE
16
CAUTION：Always Lift Your Furniture When Moving /Relocating - Do Not Drag.
Dragging Can Cause The Legs To Bend/Break.

To protect your furniture, we suggest the following:
• Avoid placing your furniture in direct sunlight.
• Do not place furniture directly under windows.
• Do not place sharp materials (knife, fork, etc.) directly onto
your furniture as sharp material may scrape and damage the
finish.
• Do not place material with high temperature directly onto the
surface of your furniture.
•Clean up spills quickly. Water left over a prolonged period of
time may cause damage. Alcohol, perfume, nail polishes,
aftershave and some medication may cause severe finish
damage if not cleaned immediately.
• Use a clean, soft, dry, lint free absorbent cloth to clean your
furniture. Do not use any detergent as they may contain
ingredients that may react and damage the finish.
NOTE: If the above care advise is not adhered to your product
warranty may become void
17

18
SAFETY BRACKETS
INSTRUCTIONS
1. Attach one Mounting Plate to the wall with the Large Screws. Make sure to
attach the Mounting Plate into a stud. If mounting into brick or masonry you
will need to acquire wall anchors.
2. Attach the second Mounting Plate to the furniture frame with the Short
Screws.
3. Move the furniture to its final position. Thread a Wall Strap through the both
Mounting Plates and tighten until snug. Do not over tighten.
4. Make sure that the Mounting Plates are firmly attached to the wall and
furniture and that the Wall Strap is snug.
WALL
BACK SLDE
SCREWS X1 SCREWS X1Anti-tiit Strap X1 Expanded plastic pipe X1
HARDWARE
washer X2