JWA GATES 75245 User manual

Imported by JWA Furniture Pty Ltd, Qld, Brisbane Australia.
For any assistance with assembly or for missing parts please refer to your receipt
ASSEMBLY INSTRUCTION
1
BUFFET
GATES
1750MM
450MM
800MM
75245/75248ITEM CODE

PRE-ASSEMBLY PREPARATION
Before you start:
1.Choose a clean, level, spacious assembly area. Avoid hard surfaces that may damage the
product
2.Take care when lng. Product should be assembled as near as possible to the point of
use
3.Ensure that you have all required contents for complete assembly
4.Always read the assembly instruons carefully before beginning assembly.
5.Keep all hardware parts and packaging out of reach of small children.
6.Do not over hten the screws and bolts as this may damage the threads
Allow 45 min For 2 person Addinal tools required
2

PARTS LIST
3
1
14 23
4
5
5
9
6
7
7
8
10
11
12
13
15 16
6
9
8

4
NO. ITEM QTY NO. ITEM QTY
NO. ITEM QTY NO. ITEM QTY
1TOP PANEL 1 PC
3
1 PC
1 PC
41 PC
52 PCE
2 PCE
2 PCE
1 PC
1 PC
10
1 PC
PARTS LIST
2
8
9
11
12
62 PCE
72 PCE
1 PC
1 PC
13
14
LEFT SIDE PANEL
RIGHT SIDE PANEL
BOTTOM PANEL
BACK PANEL
SHELF PANEL
MIDDLE PANEL
LEFT MIDDLE PANEL
RIGHT MIDDLE PANEL
A30PCS
B30PCS
C32PCS
D10PCS
E2PCS
F16PCS
4PCS
H
Φ6*35
Φ15*10
Φ6*30
Φ4*40
G1PC
Φ4*14
LEFT DOOR PANEL
RIGHT DOOR PANEL
1 PC
15
10PCS
I
10PCS
J
4PCS
K
Φ3*16
Φ2.5*12
48PCS
L
4PCS
M
16 1 PC
LEG
LEG
SHELF PANEL
LEFT DOOR PANEL
RIGHT DOOR PANEL

STEP 1:
STEP 2:
5
A X10
1
A
A X8
A
A
A
A
A
A
A
A
A
7
7
AAA
A

STEP 3:
STEP 4:
6
B X8
A X12
7
B
7
8
8
B
B
B
B
4
AA
AA
A
A
A
A
AA
A
A

STEP 5:
STEP 6:
7
C X10
4
C
C X12
D X10
2
3
11
12
10
C
C
C
CD
D
D
D
D
D
D
D
D
D
B X12
2
3
4
7
7
CCCC
C
C
C
C
C
C
C
C
B
B
B
B
B
B
B
BB8

STEP 7:
STEP 8:
8
2
G X1
G
5
5
5
G
C X10
B X10
1
2
3
CCCCC
B
B
BB
B
B
B
B
B
B
5

STEP 9:
STEP 10:
9
L X8H X4
13 16
H
HH
H
L
LL
L
14 K
L X8 K X4
15
KK
K
L
L
LL
L
L
L
L

STEP 11:
10
L X32
14 15
13 16
L
LL
L
LL
LL
LL
L
INFORMATION
Assemble these four holes first,
adjust the door and ensure it is level,
then tighten all screws.
How to adjust the door and ensure it is level,
please see the below information.

STEP 13:
11
M X4
15
L
13 14 16
66
99
L
LL
LL
LL
F X16
STEP 12:
J X10I X10
12
2
II
I
I
I
II
I
I
I
I
I
J
J
J
J
J
J
J
J
J
J
J
M
M
M
M

STEP 14:
12
CAUTION：Always Lift Your Furniture When Moving /Relocating - Do Not Drag.
Dragging Can Cause The Legs To Bend/Break.
ASSEMBLY IS COMPLETE
E X2
E
WALL
E
E
E
E
E
E
E

13
SAFETY BRACKETS
INSTRUCTIONS
1. Attach one Mounting Plate to the wall with the Large Screws. Make sure to
attach the Mounting Plate into a stud. If mounting into brick or masonry you
will need to acquire wall anchors.
2. Attach the second Mounting Plate to the furniture frame with the Short
Screws.
3. Move the furniture to its final position. Thread a Wall Strap through the both
Mounting Plates and tighten until snug. Do not over tighten.
4. Make sure that the Mounting Plates are firmly attached to the wall and
furniture and that the Wall Strap is snug.
WALL
BACK SLDE
SCREWS X1 SCREWS X1Anti-tiit Strap X1 Expanded plastic pipe X1
HARDWARE
washer X2

To protect your furniture, we suggest the following:
• Avoid placing your furniture in direct sunlight.
• Do not place furniture directly under windows.
• Do not place sharp materials (knife, fork, etc.) directly onto
your furniture as sharp material may scrape and damage the
finish.
• Do not place material with high temperature directly onto the
surface of your furniture.
•Clean up spills quickly. Water left over a prolonged period of
time may cause damage. Alcohol, perfume, nail polishes,
aftershave and some medication may cause severe finish
damage if not cleaned immediately.
• Use a clean, soft, dry, lint free absorbent cloth to clean your
furniture. Do not use any detergent as they may contain
ingredients that may react and damage the finish.
NOTE: If the above care advise is not adhered to your product
warranty may become void
14