JWA MATTHEW DESK 69929 User manual

1
ASSEMBLY INSTRUCTION
Imported by JWA Furniture Pty Ltd, Qld, Brisbane Australia.
For any assistance with assembly or for missing parts please refer to your receipt
MATTHEW DESK
ITEM CODE 69929
1440MM
590MM
1700MM

Allow 30 min For 1 person Addional tools required
PRE-ASSEMBLY PREPARATION
Before you start:
1. Choose a clean, level, spacious assembly area. Avoid hard surfaces that may
damage the product
2. Take care when liing. Product should be assembled as near as possible to the
point of use
3. Ensure that you have all required contents for complete assembly
4. Always read the assembly instrucons carefully before beginning assembly.
5. Keep all hardware parts and packaging out of reach of small children.
6. Do not over ghten the screws and bolts as this may damage the threads
7. Assembly is to be carried out by a competent adult(s) ONLY
8. During assembly, children should be kept away from the product due to possible
risk to injury.
9. Do not use this item if any components are missing or damaged.
10. Please keep the instrucons for future reference.
2

3
A
40pcs
M6X39mm
10pcs
M5X40mm
B
40pcs
M15X12mm
C
55pcs
M8X30mm
D
24pc
M3.5X14mm
E
2pcs
CR
F
4pcs
J
2pcs
CL
2pcs 2pcs
DL
2pcs
DR
PARTS LIST
1
2
3
4
5
6
SIDE PANEL
MIDDLE PANEL
SIDE PANEL
SHELF
BACK PANEL
SKIRT
7SKIRT
8
9
10
11
12
13
SKIRT
TOP PANEL
DRAWER SIDE PANEL
DRAWER SIDE PANEL
DRAWER BACK PANEL
DRAWER BASE
14 DRAWER FRONT
G
2pc
M8X50mm
K
8pc
M3.5X12mm
H
6pcs
M5X60mm
I
19pcs
M3X16mm
L
2pc
15
16
MIDDLE PANEL
SHELF
17
18
19
20
21
22
23
24
25
SHELF
BOTTOM PANEL
SIDE PANEL
SIDE PANEL
SKIRT
TOP PANEL
SKIRT
BACK PANEL
BACK PANEL
M
2pcs

01
02
03
04
05
06
07
08
09
10
11
12
13
14
4
PARTS LIST
x2
15
16
17
18
19
20
21
22
23
24
25
25

5
CAM LOCK INSTALL METHOD AS FOLLOWS
Step 1 Step 2
OR
Step 3
Fix cam nut into
the bottom of hole
then tighten it.
Lock
1.1cm
A

6
01
01
02
02
03
D
CR
D
CL
D
D
D
CL
CL
DCR
A
A A
A
A
A
F
F
F
F
STEP 1
STEP 2

7
B
B
C
C
C
C
E
E
02
02
04
04
05
STEP 3
STEP 4

8
C
C
C
C
B
B
B
B
B
B
C
C
C
C
01
01
02
02
03
04
05
05
06
07
08
STEP 5
STEP 6

9
A
A
A
C
C
C
C
C
B
B
BB
01
02 03
05
09
09
STEP 7
STEP 8

10
D
DR
D
D
D
DL
DR
× 2
× 2
A
A
E
C
C
C
B
B
C
10
11
11
11
11
10
12
12
13
13
14
14
14
STEP 9
STEP 10

11
14
14
STEP 11
STEP 12
A
A
E
E
G
G
15
16
15

12
STEP 13
STEP 14
B C
C
E
E
B
15
16
17
18
A
A
A
A
19
20

13
STEP 15
STEP 16
C
C
C
C
C
B B
B
B
B
15
16
17
18
19
20
22
23
A
A
22
B
B
C
C
C
H
H
H
H
H
H
19
23
15
20
21
22

14
STEP 17
STEP 18
I
I
G
I
I
I
19
24
25
25
24
25
M

15
STEP 19
STEP 20
ASSEMBLY COMPLETE
K
L

16
SAFETY BRACKETS
INSTRUCTIONS
1. Attach one Mounting Plate to the wall with the Large Screws. Make sure to
attach the Mounting Plate into a stud. If mounting into brick or masonry you
will need to acquire wall anchors.
2. Attach the second Mounting Plate to the furniture frame with the Short
Screws.
3. Move the furniture to its final position. Thread a Wall Strap through the both
Mounting Plates and tighten until snug. Do not over tighten.
4. Make sure that the Mounting Plates are firmly attached to the wall and
furniture and that the Wall Strap is snug.
J
HARDWARE
Wall
Back side
Large Screw x 2Wall Strap x 1Mounting Plate x 2 Small Screw x 2
x 2

7
17
To protect your furniture, we suggest the following:
•Avoid placing your furniture in direct sunlight.
•Do not place furniture directly under windows.
•Do not place sharp materials (knife, fork, etc.) directly onto
your furniture as sharp material may scrape and damage the
finish.
•Do not place material with high temperature directly onto the
surface of your furniture.
•Clean up spills quickly. Water left over a prolonged period of
time may cause damage. Alcohol, perfume, nail polishes,
aftershave and some medication may cause severe finish
damage if not cleaned immediately.
•Use a clean, soft, dry, lint free absorbent cloth to clean your
furniture. Do not use any detergent as they may contain
ingredients that may react and damage the finish.
NOTE: If the above care advise is not adhered to your product
warranty may become void