JWA DORSEY 74861 User manual

Imported by JWA Furniture Pty Ltd, Qld, Brisbane Australia.
For any assistance with assembly or for missing parts please refer to your receipt
ASSEMBLY INSTRUCTION
1
4 DRAWER WIDE TALL CHEST
DORSEY
ITEM CODE 74861/74862/74863/74864
800MM
450MM
1100MM

PRE-ASSEMBLY PREPARATION
Before you start:
1.Choose a clean, level, spacious assembly area. Avoid hard surfaces that may damage the
product
2.Take care when lng. Product should be assembled as near as possible to the point of
use
3.Ensure that you have all required contents for complete assembly
4.Always read the assembly instruons carefully before beginning assembly.
5.Keep all hardware parts and packaging out of reach of small children.
6.Do not over hten the screws and bolts as this may damage the threads
Allow 45 min For 2 person Addinal tools required
2

PARTS LIST
3
1
2
3
4
5
5
6
6
6
7
8
9
9
10
10
11
11
12
12
13
13
14
X2
X2

4
NO. ITEM QTY NO. ITEM QTY
A34PCS
B34PCS
C14PCS
D4PCS
E2PCS
F20PCS
16PCS
J
20PCS
L
M
N4PCS
16PCSK
4PCS
NO. ITEM QTY NO. ITEM QTY
1TOP PANEL 1 PC
3
1 PC
1 PC
41 PC
52 PCE
63 PCE
72 PCE
2 PCE
4 PCE
4 PCE
Φ6*35
Φ15*10
Φ6*30
Φ4*40
Φ3.5*12
Φ3*16
Φ4*14
LEFT SIDE PANEL
RIGHT SIDE PANEL
BOTTOM PANEL
BACK PANEL
BOTTOM SUPPORT PANEL
DRAWER FRONT PANEL
DRAWER FRONT PANEL
DRAWER LEFT SIDE PANEL
DRAWER RIGHT SIDE PANEL
DRAWER BACK PANEL 4 PCE
10
DRAWER BOTTOM PANEL 4 PCE
DRAWER SUPPORT PANEL 4 PCE
PARTS LIST
2
G4PCS
H8PCS
Φ3*12 48PCS
I
Φ4*35
8
9
11
12
13
1 PC
14 BOTTOM SUPPORT PANEL
CL
CR
DR
DL

STEP 1:
STEP 2:
5
A X6
1
A
I X12N X4 A X3
A
A
A
A
2
A
A
A
I
I
I
I
I
I
I
I
I
I
I
I
N(CL)
I
I
I
N(CL)
N(CL)
N(CL)
N(CL)

STEP 3:
STEP 4:
6
3
C X6
B X6
I X12N X4 A X3
2
3
A
A
A
I
I
I
I
I
I
I
I
I
I
I
I
6
6
6
B
B
BB
B
B
C
C
C
C
C
C
N(CR)
I
I
I
N(CR)
N(CR)
N(CR)
N(CR)

STEP 5:
STEP 6:
7
C X4
4
D X4
D
A X2
A
4
2
3
D
D
D
C
C

STEP 7:
STEP 8:
8
B X2
2
3
14
5
4
B
5
2
4
14

STEP 9:
STEP 10:
9
C X4
L X20
B X6
M X4
2
M
4
M
M
M
L
L
L
L
2
1
3
C
C
B
B
B
B
B

STEP 11:
STEP 12:
10
A X10
A
7
B X10F X10G X2H X4 X2
AA
BB
B
F
A
FF
H
G
7
9
9
9
10
10
10
11
11
11
12
12
13
A X10B X10F X10G X2H X4 X2
8
8
9
9
9
10
10
10
11
11
11
12
12
13
G
A
AAA
H
F
FF
BB
B

STEP 13:
STEP 14:
11
7I X12
10 X2
N X2
N(DL)
III
I
II
I X12
X2
N X2
10
8
I
II
III
N(DR)
N(DR)
N(DL)

STEP 15:
STEP 16:
12
2
14
K X16
J
J X16
J
JJ
J
JJ
J
J
J
J
JJ
J
J
JJ
J
KK
K
K
K
K
K
K
K
KK
KK
K
2
8
7
8
7

STEP 17:
13
ASSEMBLY IS COMPLETE
E X2
E
WALL
E
E
EE
E
CAUTION：Always Lift Your Furniture When Moving /Relocating - Do Not Drag.
Dragging Can Cause The Legs To Bend/Break.
E

14
SAFETY BRACKETS
INSTRUCTIONS
1. Attach one Mounting Plate to the wall with the Large Screws. Make sure to
attach the Mounting Plate into a stud. If mounting into brick or masonry you
will need to acquire wall anchors.
2. Attach the second Mounting Plate to the furniture frame with the Short
Screws.
3. Move the furniture to its final position. Thread a Wall Strap through the both
Mounting Plates and tighten until snug. Do not over tighten.
4. Make sure that the Mounting Plates are firmly attached to the wall and
furniture and that the Wall Strap is snug.
WALL
BACK SLDE
SCREWS X1 SCREWS X1Anti-tiit Strap X1 Expanded plastic pipe X1
HARDWARE
washer X2

To protect your furniture, we suggest the following:
• Avoid placing your furniture in direct sunlight.
• Do not place furniture directly under windows.
• Do not place sharp materials (knife, fork, etc.) directly onto
your furniture as sharp material may scrape and damage the
finish.
• Do not place material with high temperature directly onto the
surface of your furniture.
•Clean up spills quickly. Water left over a prolonged period of
time may cause damage. Alcohol, perfume, nail polishes,
aftershave and some medication may cause severe finish
damage if not cleaned immediately.
• Use a clean, soft, dry, lint free absorbent cloth to clean your
furniture. Do not use any detergent as they may contain
ingredients that may react and damage the finish.
NOTE: If the above care advise is not adhered to your product
warranty may become void
15