JWA MARTOS 68548 User manual

1
ASSEMBLY INSTRUCTION
ITEM CODE 68548
MARTOS BUFFET
Imported by JWA Furniture Pty Ltd, Qld, Brisbane Australia.
For any assistance with assembly or for missing parts please refer to your receipt
708MM
1140MM
390MM

Allow 60 min For 2 person AddiƟonal tools required
2
PRE-ASSEMBLY PREPARATION
Before you start:
1. Choose a clean, level, spacious assembly area. Avoid hard surfaces that may
damage the product
2. Take care when liŌing. Product should be assembled as near as possible to the
point of use
3. Ensure that you have all required contents for complete assembly
4. Always read the assembly instrucƟons carefully before beginning assembly.
5. Keep all hardware parts and packaging out of reach of small children.
6. Do not over Ɵghten the screws and bolts as this may damage the threads
7. Assembly is to be carried out by a competent adult(s) ONLY
8. During assembly, children should be kept away from the product due to possible
risk to injury.
9. Do not use this item if any components are missing or damaged.
10. Please keep the instrucƟons for future reference.

3
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
PARTS LIST
A
22pcs
B
22pcs
C
38pcs
M8X30mmM15X12mmM7X39mm
M4X14mm
M3X16mm
M5X40mm
D
FGH
KL
52pcs
M3.5X14mm
5pcs 4pcs
4pcs 4pcs 20pcs
E
J
I
18pcs
16pcs
1pcs
1pcs
CL CR
3pcs 3pcs
N
M
1pcs
M4x30mm M3.5x14mm
DR
DL
3pcs
3pcs
× 3


















MIDDLE PANEL
MIDDLE PANEL
SIDE PANEL
SIDE PANEL
BACK PANEL
SHELF
BOTTOM PANEL
TOP PANEL
BACK PANEL
DOOR
DRAWER SIDE PANEL
DRAWER SIDE PANEL
DRAWER BACK PANEL
DRAWER BASE
DRAWER FRONT
FILLER

4
CAM LOCK INSTALL METHOD AS FOLLOWS
Step 1 Step 2
OR
Step 3
Fix cam nut into
the bottom of hole
then tighten it.
Lock
1.1cm
A

5
STEP 1:
STEP 2:
D
D
CL
CL

DDD
D
D
CR
CR

D
D
D

A

A

A

A

6
STEP 3:
STEP 4:



C
C
E
E




CC
B
B

7
STEP 5:
STEP 6:





CC
BB





C
C
C
E
E
E

8
STEP 7:
STEP 8:


F
F
HH
F
FH
H


G
GG
I
N

9
STEP 9:
STEP 10:






A
A
A
B
C
C
C
B
B

10
STEP 11:
STEP 12:
J
J
J
× 2
D
D
D
L
K
L
D











11
STEP 13:
×3
D
D
DL
DR

 




CC
E
E

AA
K


B
B
C


STEP 14:
12
ASSEMBLY COMPLETE




13
SAFETY BRACKETS
INSTRUCTIONS
1. Attach one Mounting Plate to the wall with the Large Screws. Make sure to
attach the Mounting Plate into a stud. If mounting into brick or masonry you
will need to acquire wall anchors.
2. Attach the second Mounting Plate to the furniture frame with the Short
Screws.
3. Move the furniture to its final position. Thread a Wall Strap through the both
Mounting Plates and tighten until snug. Do not over tighten.
4. Make sure that the Mounting Plates are firmly attached to the wall and
furniture and that the Wall Strap is snug.
.'8*='8+
=GRR
(GIQYOJK
2GXMK9IXK]^=GRR9ZXGV^3U[TZOTM6RGZK^ 9SGRR9IXK]^
M

14
To protect your furniture, we suggest the following:
Avoid placing your furniture in direct sunlight.
Do not place furniture directly under windows.
Do not place sharp materials (knife, fork, etc.) directly onto
your furniture as sharp material may scrape and damage the
¿nish.
Do not place material with high temperature directly onto the
surface of your furniture.
Clean up spills quickly. Water left over a prolonged period of
time may cause damage. Alcohol, perfume, nail polishes,
aftershave and some medication may cause severe ¿nish
damage if not cleaned immediately.
Use a clean, soft, dry, lint free absorbent cloth to clean your
furniture. Do not use any detergent as they may contain
ingredients that may react and damage the ¿nish.
NOTE: If the above care advise is not adhered to your product
warranty may become void