JWA ELCHE 70459 User manual

1
ASSEMBLY INSTRUCTION
ITEM CODE 70459
ELCHE HIGHBOARD
Imported by JWA Furniture Pty Ltd, Qld, Brisbane Australia.
For any assistance with assembly or for missing parts please refer to your receipt
1367MM
1000MM
395MM

Allow 30 min For 2 person AddiƟonal tools required
2
PRE-ASSEMBLY PREPARATION
Before you start:
1. Choose a clean, level, spacious assembly area. Avoid hard surfaces that may
damage the product
2. Take care when liŌing. Product should be assembled as near as possible to the
point of use
3. Ensure that you have all required contents for complete assembly
4. Always read the assembly instrucƟons carefully before beginning assembly.
5. Keep all hardware parts and packaging out of reach of small children.
6. Do not over Ɵghten the screws and bolts as this may damage the threads
7. Assembly is to be carried out by a competent adult(s) ONLY
8. During assembly, children should be kept away from the product due to possible
risk to injury.
9. Do not use this item if any components are missing or damaged.
10. Please keep the instrucƟons for future reference.

3
PARTS LIST
A
22pcs
B
22pcs
C
27pcs
M8X30mmM14.8X12mm
M6X25mm M6X30mm
M7X39mm
M5X40mm
M3.5X14mm
M8X50mm
D
FGH
K
14pcs
M6X30mm
1pcs
6pcs 6pcs 4pcs
E
J
I
M
1pcs
3pcs
15pcs
6pcs
N
1pcs
L
4pcs
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
M4x30mm M3.5x14mm
FILLER















 





SIDE PANEL
SIDE PANEL
TOP PANEL
MIDDLE PANEL
SHELF
SHELF
BOTTOM PANEL
BACK PANEL
BACK PANEL
BACK PANEL
DOOR
METAL PARTS
METAL PARTS
METAL PARTS
METAL PARTS
METAL PARTS
METAL PARTS

4
STEP 1:
STEP 2:
A A

II
L
L




5
STEP 3:
STEP 4:
B
B
B





=+
KK1 K2 K1
K1
DK2
A
A


6
STEP 5:
STEP 6:
C
C
I
I
I


B
B
C
C







7
STEP 7:
STEP 8:
A A
A
A
A
A


BBB
B
B
B
C
C
C
C
C
C











8
STEP 9:
STEP 10:




I
I
CC
C










9
STEP 11:
STEP 12:
E
G
G
G
G
G
G





E
HH
H




E
F
F
F
FF
F


 

HH
!

10
STEP 13:
D
D
D

D
D
D
J
J
J


11
ASSEMBLY COMPLETE
M
M
M
M


STEP 14:

12
SAFETY BRACKETS
INSTRUCTIONS
1. Attach one Mounting Plate to the wall with the Large Screws. Make sure to
attach the Mounting Plate into a stud. If mounting into brick or masonry you
will need to acquire wall anchors.
2. Attach the second Mounting Plate to the furniture frame with the Short
Screws.
3. Move the furniture to its final position. Thread a Wall Strap through the both
Mounting Plates and tighten until snug. Do not over tighten.
4. Make sure that the Mounting Plates are firmly attached to the wall and
furniture and that the Wall Strap is snug.
.'8*='8+
=GRR
(GIQYOJK
2GXMK9IXK]^=GRR9ZXGV^3U[TZOTM6RGZK^ 9SGRR9IXK]^
^
N

13
To protect your furniture, we suggest the following:
Avoid placing your furniture in direct sunlight.
Do not place furniture directly under windows.
Do not place sharp materials (knife, fork, etc.) directly onto
your furniture as sharp material may scrape and damage the
¿nish.
Do not place material with high temperature directly onto the
surface of your furniture.
Clean up spills quickly. Water left over a prolonged period of
time may cause damage. Alcohol, perfume, nail polishes,
aftershave and some medication may cause severe ¿nish
damage if not cleaned immediately.
Use a clean, soft, dry, lint free absorbent cloth to clean your
furniture. Do not use any detergent as they may contain
ingredients that may react and damage the ¿nish.
NOTE: If the above care advise is not adhered to your product
warranty may become void