JWA HARDING 74709 User manual

Imported by JWA Furniture Pty Ltd, Qld, Brisbane Australia.
For any assistance with assembly or for missing parts please refer to your receipt
ASSEMBLY INSTRUCTION
1
74709
3 DOOR BUFFET
HARDING
ITEM CODE
1500MM
400MM
760MM

PRE-ASSEMBLY PREPARATION
Before you start:
1.Choose a clean, level, spacious assembly area. Avoid hard surfaces that may damage the
product
2.Take care when lig. Product should be assembled as near as possible to the point of
use
3.Ensure that you have all required contents for complete assembly
4.Always read the assembly instrucns carefully before beginning assembly.
5.Keep all hardware parts and packaging out of reach of small children.
6.Do not over hten the screws and bolts as this may damage the threads
Allow 1 hour For 2 person Addinal tools required
2

PARTS LIST
3
1
2
3
4
4
5
6
7
8
9
9
10
11
12
10
11
14
12
13
13
15
16

4
NO. ITEM QTY NO. ITEM QTY
A16PCS
B16PCS
C24PCS
D8PCS
E2PCS
F36PCS
H
6PCS
L
M12PCS
N1PC
O
2PCS
K
2PCS
Φ6*35
Φ15*10
Φ6*30
Φ4*40
PARTS LIST
Φ4*14
G4PCS
8PCS
Φ6*30
P1PC
Φ3.5*12
Q8PCS
Φ3*1.5
R8PCS
I4PCS S8PCS
Φ3*16
Φ2.5*12
J3PCS
Φ5*30
T8PCS

10
5
NO. ITEM QTY NO. ITEM QTY
1TOP PANEL 1 PC
3
1 PC
1 PC
42 PCE
51 PC
61 PC
71 PC
2 PCE
2 PCE
2 PCE
81 PC
2 PCE
10
2 PCE
9
1 PC
1 PC
PARTS LIST
2LEFT SIDE PANEL
RIGHT SIDE PANEL
11
12
13
14
15
SHELF PANEL
SHELF PANEL
BOTTOM PANEL
LEFT MIDDLE PANEL
RIGHT MIDDLE PANEL
BACK PANEL
METAL LEG
METAL LEG
METAL LEG
METAL LEG
LEFT DOOR PANEL
RIGHT DOOR PANEL
1 PC
16 RIGHT DOOR PANEL

STEP 1:
STEP 2:
6
A X8
1
A
A X4
A
A
A
A
A
A
A
2
3
A
A
A
A

STEP 3:
STEP 4:
7
A X4
7
A
C X4
A
A
A
8
B X4
4
2
7
B
B
B
B
C
C
C
C

STEP 5:
STEP 6:
8
B
4
C X4B X4
3
8
B
B
B
C
C
C
C
C X8B X8
8
3
2
1
7
B
B
B
B
B
B
B
B
C
C
C
C
4
4

STEP 7:
STEP 8:
9
9
P X1
P
9
9
9
P
9
9
3
2
1

STEP 9:
STEP 10:
10
6
D
O X8
C X8D X8
3
2
D
D
D
D
D
D
D
C
C
C
C
6
3
OO
OO
OO
OO

STEP 11:
STEP 12:
11
N X1
M X4
M X8
N X1L X2
N
M
MM
M
M
M
M
M11
11
10
10
12
12
2
L
1
L
11
11
13
13
12
12
10
10
M
M
M
M
L
L
N

STEP 13:
STEP 14:
12
S X8N X1
T
T X8
T
T
T
T
T
T
T
N
S
S
S
S
S
S
S
S
62
10
10
11
11
K X6J X3G X4H X2F X12
14
15
16
H
H
G
G
G
G
F
F
F
F
F
F
K
K
K

STEP 15:
STEP 16:
13
F X24
F
14 15 16
F
F
F
F
F
F
I X4
5
15
I
I
I
I

STEP 17:
STEP 18:
14
R X8Q X8
Q
Q
Q
Q
Q
Q
Q
Q
R
R
R
R
R
RR
R
R
R
E X2
E
E
E
WALL
EE
E
EE
E

ASSEMBLY IS COMPLETE
15

16
SAFETY BRACKETS
INSTRUCTIONS
1. Attach one Mounting Plate to the wall with the Large Screws. Make sure to
attach the Mounting Plate into a stud. If mounting into brick or masonry you
will need to acquire wall anchors.
2. Attach the second Mounting Plate to the furniture frame with the Short
Screws.
3. Move the furniture to its final position. Thread a Wall Strap through the both
Mounting Plates and tighten until snug. Do not over tighten.
4. Make sure that the Mounting Plates are firmly attached to the wall and
furniture and that the Wall Strap is snug.
WALL
BACK SLDE
SCREWS X1 SCREWS X1Anti-tiit Strap X1 Expanded plastic pipe X1
HARDWARE
washer X2

To protect your furniture, we suggest the following:
• Avoid placing your furniture in direct sunlight.
• Do not place furniture directly under windows.
• Do not place sharp materials (knife, fork, etc.) directly onto
your furniture as sharp material may scrape and damage the
finish.
• Do not place material with high temperature directly onto the
surface of your furniture.
•Clean up spills quickly. Water left over a prolonged period of
time may cause damage. Alcohol, perfume, nail polishes,
aftershave and some medication may cause severe finish
damage if not cleaned immediately.
• Use a clean, soft, dry, lint free absorbent cloth to clean your
furniture. Do not use any detergent as they may contain
ingredients that may react and damage the finish.
NOTE: If the above care advise is not adhered to your product
warranty may become void
17