JWA SMITHERS 69423 User manual

Imported by JWA FurniturePty Ltd, Qld, Brisbane Australia.
For anyassistance with assembly or for missing parts please refer to your receipt
ASSEMBLY INSTRUCTION
1
69423
1 Drawer Bedside
SMITHERS
ITEM CODE
600MM
440MM
370MM

PRE-ASSEMBLY PREPARATION
Before you start:
1.Choose a clean, level, spacious assembly area. Avoid hard surfaces that may damage the
product
2.Take care when ling. Product should be assembled as near as possible to the point of
use
3.Ensure that you have all requiredcontents for complete assembly
4.Always read the assembly instrucons carefully before beginningassembly.
5.Keep all hardware partsand packaging out of reach of small children.
6.Do not over ghten the screws and bolts as this may damage the threads
Allow 30 min For 1 person Addionaltools required
2

PARTS LIST
3

4
NO. ITEM QTY NO. ITEM QTY
A14PCS
B14PCS
C20PCS
D12PCS
E1PC
4PCS
H
1PC
K
1PC
L
1PC
M
4PCSI
NO. ITEM QTY NO. ITEM QTY
1LEFT SIDE PANEL 1 PC
2
3
1 PC
2 PCE
41 PC
51 PC
61 PC
1 PC
81 PC
91 PC
Φ6*28
Φ12*10
Φ6*30
Φ3.5*12
Φ4*35
RIGHT SIDE PANEL
SUPPORT PANEL
MIDDLE SUPPORT PANEL
TOP PANEL
BOTTOM PANEL
BACK PANEL
DRAWER BACK PANEL
10
DRAWER FRONT PANEL
DRAWER RIGHT SIDE PANEL 1 PC
7
11
12
DRAWER LEFT SIDE PANEL 1 PC
DRAWER BOTTOM PANEL 1 PC
PARTS LIST

STEP 1:
STEP 2:
5
L X1D X6A X6
（L）（R）
A
A
AA
A
A
（L）
ADD
E
5
E X1A X4

STEP 3:
STEP 4:
6
C X7B X3
C X7B X3

STEP 5:
STEP 6:
7
C X4B X4
A
A
A

STEP 7:
STEP 8:
8
II
I
I
I X4
K X1H X4C X2B X4A X4
H
H

STEP 9:
STEP 10:
9
M X1
D X6
M（L
M（R）
）
D
DD
DDD
WARNING: IT IS STRONGLY RECOMMENDED THAT YOUANCHOR THIS PRODUCT TOA WALL.
YOUNG CHILDREN MAY BE INJURED OR KILLED BY TIPPING FURNITURE OVER. ALWAYS USE AN ANTI TOPPLE RESTRAINT.
This hardware, when properly installed, could provide protection against the unexpected tipping of furniture due to improper use.
Please ensure the anti-tipping hardware provided is suitable for your wall or else it might damage your wall during installation.
Please refer to page 6 for guidance on suitable wall fixings.
E X1

STEP 11:
STEP 12:
10

ASSEMBLY IS COMPLETE
11

12
SAFETY BRACKETS
INSTRUCTIONS
1. Attach one Mounting Plate to the wall with the Large Screws. Make sure to
attach the Mounting Plate into a stud. If mounting into brick or masonry you
will need to acquire wall anchors.
2. Attach the second Mounting Plate to the furniture frame with the Short
Screws.
3. Move the furniture to its final position. Thread a Wall Strap through the both
Mounting Plates and tighten until snug. Do not over tighten.
4. Make sure that the Mounting Plates are firmly attached to the wall and
furniture and that the Wall Strap is snug.
WALL
BACK SLDE
SCREWS X1 SCREWS X1WALL FIXING X1 Expanded plastic pipe X1
HARDWARE

To protect your furniture, we suggest the following:
• Avoid placing your furniture in direct sunlight.
• Do not place furniture directly under windows.
• Do not place sharp materials (knife, fork, etc.) directly onto
your furniture as sharp material may scrape and damage the
finish.
• Do not place material with high temperature directly onto the
surface of your furniture.
•Clean up spills quickly. Water left over a prolonged period of
time may cause damage. Alcohol, perfume, nail polishes,
aftershave and some medication may cause severe finish
damage if not cleaned immediately.
• Use a clean, soft, dry, lint free absorbent cloth to clean your
furniture. Do not use any detergent as they may contain
ingredients that may react and damage the finish.
NOTE: If the above care advise is not adhered to your product
warranty may become void
13