JWA MYERS 76431 User manual

Imported by JWA Furniture Pty Ltd, Qld, Brisbane Australia.
For any assistance with assembly or for missing parts please refer to your receipt
ASSEMBLY INSTRUCTION
1
400mm
551mm
615mm
BEDSIDE TABLE
MYERS
ITEM CODE 76431

PRE-ASSEMBLY PREPARATION
Before you start:
1.Choose a clean, level, spacious assembly area. Avoid hard surfaces that may damage the
product
2.Take care when lg. Product should be assembled as near as possible to the point of
use
3.Ensure that you have all required contents for complete assembly
4.Always read the assembly instruons carefully before beginning assembly.
5.Keep all hardware parts and packaging out of reach of small children.
6.Do not ovghten the screws and bolts as this may damage the threads
Allow 45 min For person Addnal tools required
2
2

PARTS LIST
3
10
12
12
11
11
1
2
34
6
7
8
9
5

4
NO. ITEM QTY NO. ITEM QTY
A18PCS
18PCS
20PCS
4PCS
4PCS
1PC 1PC
10PCS
1PC
2PCS
4PCS
4PCS
B
C
10
9
PARTS LIST
D
E
F
H
G
I
J
K
L
BOTTOM PANEL
LEFT SIDE PANEL
RIGHT SIDE PANEL
BACK PANEL
DRAWER FRONT
DRAWER LEFT
PANEL
LEG
LEG
PANEL
PANEL
PANEL
PANEL
DRAWER RIGHT
DRAWER BACK
DRAWER BOTTOM
NO. ITEM QTY NO. ITEM QTY
11 PC
3
1 PC
41 PC
1 PC
51 PC
6
1 PC
71 PC
1 PC
1 PC
8
12
11
1 PC
2 PCS
2 PCS
2
TOP PANEL
(CL) (DL) (DR) (CR)
4x30mm
4x35mm
3x12mm
3x16mm

STEP 1:
STEP 2:
5
4xE4xC
6xG1xF
G
G
G
G
F
F
G
G
(CL)
(CR)
G
F
3
4
C
C
C
C
E
E
E
E
3
4
2

STEP 3:
STEP 4:
6
10xA 10xB 12xC
A
A
A
A
A
A
B
B
B
B
B
B
C
C
C
C
C
C
C
C
12
A
AA
A
B
B
B
B
C
C
C
C
12
12
11
11
11
3
2
4
34
5

STEP 5:
STEP 6:
7
4xD
4xC
4xB4xA
A
A
A
A
B
BB
B
CC
C
C
3
2
1
4
D
D
D
D
6
7
8
9

STEP 7:
STEP 8:
8
4xB4xA 1xH 2xI4xG1xF
A
A
A
A
B
B
B
B
I
I
H
G
G
G
G
F
F
(DL)
(DR)
F
F
G
G
10

STEP 9：
STEP 10:
9
1xL
4xK4xJ
J
J
J
J
K
K
K
K
L
L

STEP 11:
10
L
L
1xL

11
SAFETY BRACKETS
INSTRUCTIONS
1. Attach one Mounting Plate to the wall with the Large Screws. Make sure to
attach the Mounting Plate into a stud. If mounting into brick or masonry you
will need to acquire wall anchors.
2. Attach the second Mounting Plate to the furniture frame with the Short
Screws.
3. Move the furniture to its final position. Thread a Wall Strap through the both
Mounting Plates and tighten until snug. Do not over tighten.
4. Make sure that the Mounting Plates are firmly attached to the wall and
furniture and that the Wall Strap is snug.
HARDWARE
Wall Back side
SCREWS X1 SCREWS X1Anti-tiit Strap X1 Expanded plastic pipe X1 washer X2

To protect your furniture, we suggest the following:
•Avoid placing your furniture in direct sunlight.
•Do not place furniture directly under windows.
•Do not place sharp materials (knife, fork, etc.) directly onto
your furniture as sharp material may scrape and damage the
finish.
•Do not place material with high temperature directly onto the
surface of your furniture.
•Clean up spills quickly. Water left over a prolonged period of
time may cause damage. Alcohol, perfume, nail polishes,
aftershave and some medication may cause severe finish
damage if not cleaned immediately.
•Use a clean, soft, dry, lint free absorbent cloth to clean your
furniture. Do not use any detergent as they may contain
ingredients that may react and damage the finish.
NOTE: If the above care advise is not adhered to your product
warranty may become void
12