JWA RAFAELA 69421 User manual

Imported by JWA Furniture Pty Ltd, Qld, Brisbane Australia.
For any assistance with assembly or for missing parts please refer to your receipt
ASSEMBLY INSTRUCTION
1
69421
2 DRAWER DESK
RAFAELA
ITEM CODE
750MM
590MM
400MM

PRE-ASSEMBLY PREPARATION
Before you start:
1.Choose a clean, level, spacious assembly area. Avoid hard surfaces that may damage the
product
2.Take care when ling. Product should be assembled as near as possible to the point of
use
3.Ensure that you have all required contents for complete assembly
4.Always read the assembly instrucons carefully before beginning assembly.
5.Keep all hardware parts and packaging out of reach of small children.
6.Do not over ghten the screws and bolts as this may damage the threads
Allow 30 min For 1 person Addional tools required
2

PARTS LIST
3
L
R
R
L
16
16

4
NO. ITEM QTY NO. ITEM QTY
A10PCS
B10PCS
C20PCS
D8PCS
E2PCS
F2PCS
2PCS
I
6PCS
J
4PCS
K
2PCS
L
6PCSH
G
M1PC
N8PCS
NO. ITEM QTY NO. ITEM QTY
1TOP PANEL 1 PC
2
3
1 PC
1 PC
41 PC
52 PCE
62 PCE
72 PCE
1 PC
11 1 PC
1 PC
Φ6*35
Φ12*10
Φ6*30
Φ4.5*50
Φ6*30
Φ6*14
Φ4*40
Φ3*12
Φ4*25
Φ3*20
BOTTOM PANEL
LEFT SIDE PANEL
RIGHT SIDE PANEL
DRAWER FRONT PANEL
DRAWER LEFT SIDE PANEL
DRAWER RIGHT SIDE PANE
8DRAWER BACK SIDE PANEL 2 PCE
MIDDLE UPER PANEL
BACK UNDER SUPPORT PANEL
BACK UPER SUPPORT PANEL
10
13
2 PCE
9DRAWER BOTTOM PANEL
14LR
BACK PANEL 1 PC
LEFT SIDE LEG PANEL 2 PCE
15LR RIGHT SIDE LEG PANEL 2 PCE
16 DRAWER STOP PANEL 2 PCE
PARTS LIST
12
Φ8*10 8PCS Φ3.5*35
17
BACK UPER SUPPORT PANEL
BACK UPER SUPPORT PANEL 1 PC

STEP 1:
STEP 2:
5
N
N
X2
N X8
X2
C X8B X4
A X4

STEP 3:
STEP 4:
6
4
10
L X2I X2
C X6
B X6
A X6

L
L
R
R
STEP 5:
STEP 6:
7
K X4H X6C X6
F X2E X2

STEP 7:
STEP 8:
8
L
L
R
R
7
G X4D X4
G X4D X4
L
L
R
R
7

STEP 9:
STEP 10:
9
J X6
R
L
R
L
7

ASSEMBLY IS COMPLETE
10

11
SAFETY BRACKETS
INSTRUCTIONS
1. Attach one Mounting Plate to the wall with the Large Screws. Make sure to
attach the Mounting Plate into a stud. If mounting into brick or masonry you
will need to acquire wall anchors.
2. Attach the second Mounting Plate to the furniture frame with the Short
Screws.
3. Move the furniture to its final position. Thread a Wall Strap through the both
Mounting Plates and tighten until snug. Do not over tighten.
4. Make sure that the Mounting Plates are firmly attached to the wall and
furniture and that the Wall Strap is snug.
WALL
BACK SLDE
SCREWS X1 SCREWS X1WALL FIXING X1 Expanded plastic pipe X1
HARDWARE

To protect your furniture, we suggest the following:
• Avoid placing your furniture in direct sunlight.
• Do not place furniture directly under windows.
• Do not place sharp materials (knife, fork, etc.) directly onto
your furniture as sharp material may scrape and damage the
finish.
• Do not place material with high temperature directly onto the
surface of your furniture.
•Clean up spills quickly. Water left over a prolonged period of
time may cause damage. Alcohol, perfume, nail polishes,
aftershave and some medication may cause severe finish
damage if not cleaned immediately.
• Use a clean, soft, dry, lint free absorbent cloth to clean your
furniture. Do not use any detergent as they may contain
ingredients that may react and damage the finish.
NOTE: If the above care advise is not adhered to your product
warranty may become void
12