JWA ACASTA 68209 User manual

ASSEMBLY INSTRUCTIONS
ACASTA
OUTDOOR LOUNGE SETTING
ITEM CODE 68209
Imported by JWA Furniture Pty Ltd, Brisbane, QLD, Australia
For any assistance with assembly or for missing parts, please refer to your receipt
X2

PRE-ASSEMBLY PREPARATION
Allow 60min For 2 person
Before you start:
1. Choose a clean, level, spacious assembly area. Avoid hard surfaces that may
damage the product
2. Take care when lifting. Product should be assembled as near as possible to the
point of use
3. Ensure that you have all required contents for complete assembly
4. Always read the assembly instructions carefully before beginning assembly.
5. Keep all hardware parts and packaging out of reach of small children.
6. Do not over tighten the screws and bolts as this may damage the threads
7. Assembly is to be carried out by a competent adult(s) ONLY
8. During assembly, children should be kept away from the product due to possible
risk to injury.
9. Do not use this item if any components are missing or damaged.
10. Please keep the instructions for future reference.
1

2 x Outdoor Armchair
2PCS
2PCS
2PCS
2PCS
Washer Allen keyBoltBolt
M6 x 30, 4PCS M6 x 35, 12PCS M6, 16PCS M6, 1PC
2

Outdoor 2 seater lounge
Washer Allen keyBoltBolt
M6 x 30, 2PCS M6 x 35, 7PCS M6, 8PCS M6, 1PC
3

Outdoor coffee table
Washer Allen key
4
M6*12PCS

Part A: Assembling an armchair
You will need the following
Step 1
•Attach parts 1 and 2 to 3 as shown below. Use bolt B, the longer
bolt, threaded through washer C. Do this for each of the bolt holes
on the leg end. Do not fully tighten for now tighten to only semi-
firm.
Bolts
Make sure these protrusions click-in
Washer Allen key
5

Part A: Assembling an armchair
Step 2
•Attach seat 4 to both left and right arms 1 & 2 as shown below. Use
bolt B, the longer bolt, threaded through washer C. Do this for all of
the bolt holes. Do not fully tighten for now tighten to only semi-
firm.
Washer Allen key
You will need the following
Bolts
Bolts
6

Part A: Assembling an armchair
You will need the following
Step 3
•Fasten the front lip of the seat 4, to both left and right arms, 1&2.
Use Bolt A, the shorter bolt, threaded through washer C. Do not
fully tighten for now tighten to only semi-firm.
Bolts
Washer Allen key
7

Part A: Assembling an armchair
Step 4
•Flip the chair the right way up and put it onto an even surface. Push
down on the arms on both sides to level the chair. Do not push
beyond your own balance.
Push
Push
Step 5
•Flip the chair upside down again and now firmly tighten all the
bolts. WARNING do not over tighten the bolts as it could damage
the chair.
Step 6
•Repeat steps 1-5 for the other armchair.
8

Part B: Assembling the 2 seater lounge
You will need the following
Step 1
•Attach parts 1 and 2 to 5 as shown below. Use bolt B, the longer
bolt, threaded through washer C. Do this for each of the bolt holes
on the leg end. Do not fully tighten for now tighten to only semi-
firm.
Bolts
Make sure these protrusions click-in
Washer Allen key
9

Step 2
•Attach seat 6 to both left and right arms 1 & 2 and the backrest 5 as
shown below. Use bolt B, the longer bolt, threaded through washer
C. Do this for all of the bolt holes. Do not fully tighten for now
tighten to only semi-firm.
Washer Allen key
You will need the following
Bolts
Bolts
Part B: Assembling the 2 seater lounge
Bolts
10

You will need the following
Step 3
•Fasten the front lip of the seat 6, to both left and right arms, 1&2.
Use Bolt A, the shorter bolt, threaded through washer C. Do not
fully tighten for now tighten to only semi-firm.
Bolts
Washer Allen key
Part B: Assembling the 2 seater lounge
11

Step 4
•Flip the lounge the right way up and put it onto an even surface.
Push down on the arms on both sides to level the chair. Do not
push beyond your own balance.
Step 5
•Flip the chair upside down again and now firmly tighten all the
bolts. WARNING do not over tighten the bolts as it could damage
the chair.
Part B: Assembling the 2 seater lounge
Push
Push
12

Part C: Assembling the coffee table
You will need the following
Step 1
•Attach both fixed link 7 pieces with both legs 8, as shown below.
Use bolt A, the longer bolt, threaded through washer C. Do this for
all of the bolt holes on the “fixed links”. Do not fully tighten for
now tighten to only semi-firm.
Bolts
Washer Allen key
13
Bolts
Bolts
Bolts

Part C: Assembling the coffee table
You will need the following
Step 2
•Flip the unit over (right side up). Attach connecting rod 10 to the
fixed link pieces 7. Use bolt E, the shorter bolt, for this. Thread
through washer C. Do not fully tighten for now tighten to only
semi-firm.
Washer Allen key
14

Part C: Assembling the coffee table
Step 3
•Put the table onto an even surface. Push down on the legs on both
sides to level the table. Do not push beyond your own balance.
Push
Push
Step 3
•Flip the table upside down again and now firmly tighten all the
bolts. WARNING do not over tighten the bolts as it could damage
the table.
15

Part C: Assembling the coffee table
Step 4
•Place the glass 9 onto the frame. Make sure that the suction caps
are firmly engaged to the glass.
You will need the following
16

Assembly is complete
17

18