JWA MESA 68259 User manual

ASSEMBLY INSTRUCTIONS
MESA
3 Piece Sun Lounge Setting
ITEM CODE 68259
Imported by JWA Furniture Pty Ltd, Brisbane, QLD, Australia
For any assistance with assembly or for missing parts, please refer to your receipt

PRE-ASSEMBLY PREPARATION
Allow 60min For 2 person You will need a tape
measure.
Before you start:
1. Choose a clean, level, spacious assembly area. Avoid hard surfaces that may
damage the product
2. Take care when lifting. Product should be assembled as near as possible to the
point of use
3. Ensure that you have all required contents for complete assembly
4. Always read the assembly instructions carefully before beginning assembly.
5. Keep all hardware parts and packaging out of reach of small children.
6. Do not over tighten the screws and bolts as this may damage the threads
7. Assembly is to be carried out by a competent adult(s) ONLY
8. During assembly, children should be kept away from the product due to possible
risk to injury.
9. Do not use this item if any components are missing or damaged.
10. Please keep the instructions for future reference.
1

2
PARTS LIST
Sun Lounge
N.B. mesh is not shown on the seat for illustrative purposes
Lever

3
PARTS LIST
Side Table

Part A: Sun lounge
You will need the following
Step 1
4
•Prepare a floor or benchtop with a protective blanket or carboard.
•Connect Right Arm(1) to the 3x fixed links(B) part 3, as shown below.
•Secure with 2x bolts(A) for each fixed link. Use Wrench(C).
•Tighten only until the bolt is a little firm in the thread, do not fasten
completely.
•Repeat for the Left Arm(2).

You will need the following
5
Part A: Sun lounge
Step 2
•Attached the 2 fixed links(A) part 4, As shown below.
•Secure with 2x bolt (A) at every connection point. Use Wrench(C).
•Tighten only until the bolt is a little firm in the thread, do not fasten
completely.

You will need the following
6
N.B. mesh is not shown on the seat for illustrative purposes
Step 3
•Spread open the seat.
•Insert the 2 fixed links(A) part 4, As shown below.
•Expand the fixed links(A) part 4, with the lever(E). You will need to
rotate the lever, then push the lever through when you have reached
the mesh and turn again.
•Expand the seat to around 48cm in width.
Part A: Sun lounge
Lever

7
You will need the following
Part A: Sun lounge
Step 4
•With the aide of a 2nd person, insert the seat into the arms, as shown
below.
•Secure with a bolt (A) at the 6 connection points shown below. Use
Wrench(C).
•Tighten only until the bolt is a little firm in the thread, do not fasten
completely.
•It the seat does not fit inside the arms, got back to step 3 to either
widen or contract the seat.

Assembly is complete
8
Step 5
•Stand the lounge on a level surface.
•Push down on the arms of the lounge until it levels out. Do not lean
beyond your own balance.
•Once level fully fasten all the bolts with wrench(C).
•Do not over tighten, this may damage the product.
Part A: Sun lounge
Step 6
•Repeat for the other sun lounge.

Part B: Side Table
You will need the following
9
Step 1
•Lay the table top(7) on the pre-prepared surface, upside down with the
bolt holes facing up.
•Attach one of the legs(8) to the table top(7). Secure with 2x bolts(A).
Fasten with wrench(C).
•Tighten only until the bolt is a little firm in the thread, do not fasten
completely.
•Repeat for the other 3 legs.

10
Part B: Side Table
Step 2
•Stand the table up the right way.
•Push down on the table until it levels out. Do not lean beyond your own
balance.
•Once level, turn the table back over, fully fasten all the bolts with
wrench(C).
•Do not over tighten, this may damage the product.
Step 3
•Stand the table up the right way.
•Place the tempered glass(9) into the table. As shown below.

11
Assembly is complete

12