JWA CUETA 68232 User manual

ASSEMBLY INSTRUCTIONS
CUETA
5 Piece Outdoor Bar Setting
ITEM CODE 68232
Imported by JWA Furniture Pty Ltd, Brisbane, QLD, Australia
For any assistance with assembly or for missing parts, please refer to your receipt

PRE-ASSEMBLY PREPARATION
Allow 60min
For 2 person
Before you start:
1. Choose a clean, level, spacious assembly area. Avoid hard surfaces that may
damage the product
2. Take care when lifting. Product should be assembled as near as possible to the
point of use
3. Ensure that you have all required contents for complete assembly
4. Always read the assembly instructions carefully before beginning assembly.
5. Keep all hardware parts and packaging out of reach of small children.
6. Do not over tighten the screws and bolts as this may damage the threads
7. Assembly is to be carried out by a competent adult(s) ONLY
8. During assembly, children should be kept away from the product due to possible
risk to injury.
9. Do not use this item if any components are missing or damaged.
10. Please keep the instructions for future reference.
1

2
PARTS LIST
Part A: Bar Table

Part A: Bar Table
You will need the following
3
Step 1
•Prepare a floor or benchtop with a protective blanket or cardboard.
•Prepare 8x bolt kits buy threading bolt(A) through washer(B).
•Place the table frame(1) on the surface with the bottom facing up.
•Attach one of the legs(2) to the table frame(1), as shown below. Secure with 4x
bolt kits. Fasten Allen key(C)
•Tighten only until the bolt is a little firm in the thread, do not fasten
completely.
•Repeat for the other leg(2).

You will need the following
4
Step 2
•Prepare 4x bolt sets by threading bolt(A) threaded through washer(B).
•Insert the spreader bar(3) as shown below.
•Secure with 2 bolt sets on each end, as shown below. Fasten with Allen key(C)
•Tighten only until the bolt is a little firm in the thread, do not fasten
completely.
Part A: Bar Table

•With the aid of a second person,stand the table up the right way.
•Push down on the table until it levels out. Do not lean beyond your own
balance.
•Once level, turn the table back over, fully fasten all the bolts with Allen Key(C).
•Do not over tighten, this may damage the product.
You will need the following
5
Part A: Bar Table
Step 3
Step 4
•With the aid of a second person, stand the table up the right way.
•Place the tempered glass(4) on to the table. As shown below.

6
PARTS LIST
Part B: Bar Stool

Part B: Bar Stool. Assemble one at a time.
You will need the following
7
Step 1
•Prepare 8x bolt kits buy threading bolt(A) through washer(B).
•Place the seat panel(1) on the surface with the bottom facing up.
•Attach one of the sides(2) to the seat panel(1), as shown below. Secure with 4x
bolt kits. Fasten Allen key(D)
•Tighten only until the bolt is a little firm in the thread, do not fasten
completely.
•Repeat for the other side(2).

You will need the following
8
Step 2
•Prepare 4x bolt kits buy threading bolt(B) through washer(C).
•Insert one of the connecting rods(3), secure with 2 bolt sets on each end as
shown below. Fasten with Allen Key(D)
•Tighten only until the bolt is a little firm in the thread, do not fasten
completely.
•Repeat for the other connecting rod(D).
Part B: Bar Stool. Assemble one at a time.

Assembly is complete
9
•Stand the stool up the right way.
•Push down on the stool until it levels out.
•Do not lean beyond your own balance.
•Once level, turn the stool back over, fully fasten all the bolts with Allen Key(D).
•Do not over tighten, this may damage the product.
Step 3
•Repeat for the other 3 bar stools.
Step 4
Part B: Bar Stool. Assemble one at a time.

10