JWA ANTHONY 71288 User manual

ASSEMBLY INSTRUCTION
ANTHONY
1 Seat Outdoor Swing
ITEM CODE:71288
Imported by JWA Furniture Pty Ltd, Qld, Brisbane Australia.
For any assistance with assembly or for missing parts please refer to your receipt
1

Allow 30 min For 1 persons Additional tools
2
PRE-ASSEMBLY PREPARATION
Before you start:
1. Choose a clean, level, spacious assembly area. Avoid hard surfaces that may
damage the product
2. Take care when lifting. Product should be assembled as near as possible to the
point of use
3. Ensure that you have all required contents for complete assembly
4. Always read the assembly instructions carefully before beginning assembly.
5. Keep all hardware parts and packaging out of reach of small children.
6. Do not over tighten the screws and bolts as this may damage the threads
7. Assembly is to be carried out by a competent adult(s) ONLY
8. During assembly, children should be kept away from the product due to possible
risk to injury.
9. Do not use this item if any components are missing or damaged.
10. Please keep the instructions for future reference.

PARTS LIST
3

You will need the following
Step 1
•Prepare a floor or benchtop with a protective blanket or
cardboard.
•Attach the connection bar(G) to the 2 arm part(A),Secure with
bolt(M), threaded through washer(P) .Fasten with Allen as shown
below.
•Repeat the step for other end.
4

Step 2
You will need the following
•Attach the connection bar(F) to the 2 foot part(D)(E),Secure the
bracket on the bar with bolt(J), threaded through washer(P)
Fasten with Allen as shown below.
•Repeat the step for other connection bar.
5

Step 3
You will need the following
•Insert connection bar (I) to the plastic parts, thread bolt(K) from
the outside of the plastic bar .Fasten with Allen key(S) as shown
below.
•You will need to repeat the step for each end.
6

Step 4
You will need the following
•Connect finished part from previous step to the finished foot
part,as show below.(H).
•Thread bolt(O) from the outside through the foot part.Lock the
inside with washer(P) and nut(Q). Fasten with Allen key(S) and
Wrench (R), as shown below.
•Repeat the steps for other 3 side as shown below.
7

Step 5
You will need the following
•Insert the seat panel(B) to finished arm part, as shown below.
•Secure with bolt(N), threaded from the outside, through Seat(B).
Place the plastic washer(T) between seat panel(B) and arm part
(A). Lock the inside with washer(P) and nut(Q). Fasten with Allen
key(S)and Wrench(R), as shown below .
•Repeat the step for other end.
8

Step 6
You will need the following
•Attach the backrest to the finished fame.
•Thread bolt(U) from the outside through the backrest.Lock the
inside with washer(P) and nut(Q). Fasten with Allen key(S) and
Wrench (R), as shown below.
•Repeat the step for other end.
9

Step 7
You will need the following
•Secure with bolt(N), threaded from the outside, through
backrest(C). Place the plastic washer(T) between arm part(A) and
backrest(C). Lock the inside with washer(P) and nut(Q). Fasten
with Allen key(S)and Wrench(R), as shown below .
•Repeat the step for other end.
10

Step 8
You will need the following
•Secure the chair upper base to bottom part, as shown below.
•Insert bolt(O) from inside as shown. Lock the other side the bolt
with washer(P) and nut(Q), as shown below.
•Fasten with Allen key(S) and wrench(R).
•Repeat the step for rest 3 ends.
11

Assembly is complete
12