Küppersbusch EDIP 6650.0 User manual

Bedienungsanleitung
Instructions Booklet
Mode d’emploi
Libretto Istruzioni
Gebruiksaanwijzing
Manual de instrucciones
Manual de Instruções
NL
IT
FR
GB
DE
EDIP 6650.0
EDIP 9650.0
PT
ES

12GB
CONTENTS
Dear Customer,
If you follow the recommendations
contained in this Instruction Manual,
your appliance will give you constant
high performance and will remain
efficient for many years to come.
RECOMMENDATIONSANDSUGGESTIONS 13
CHARACTERISTICS 14
INSTALLATION 15
USE 17
MAINTENANCE 18

13GB
RECOMMENDATIONS AND SUGGESTIONS
INSTALLATION
• The manufacturer will not be held liable for any damages resulting
from incorrect or improper installation.
• The minimum safety distance between the cooker top and the
extractor hood is 650 mm.
• Check that the mains voltage corresponds to that indicated on the
rating plate fixed to the inside of the hood.
• For Class I appliances, check that the domestic power supply
guarantees adequate earthing.
• Connect the extractor to the exhaust flue through a pipe of
minimum diameter 120 mm. The route of the flue must be as short
as possible.
• Do not connect the extractor hood to exhaust ducts carrying
combustion fumes (boilers, fireplaces, etc.).
• If the extractor is used in conjunction with non-electrical appliances
(e.g. gas burning appliances), a sufficient degree of aeration must
be guaranteed in the room in order to prevent the backflow of
exhaust gas. The kitchen must have an opening communicating
directly with the open air in order to guarantee the entry of clean
air.
USE
• The extractor hood has been designed exclusively for domestic
use to eliminate kitchen smells.
• Never use the hood for purposes other than for which it has ben
designed.
• Never leave high naked flames under the hood when it is in
operation.
• Adjust the flame intensity to direct it onto the bottom of the pan
only, making sure that it does not engulf the sides.
• Deep fat fryers must be continuously monitored during use:
overheated oil can burst into flames.
• The hood should not be used by children or persons not instructed
in its correct use.
MAINTENANCE
• Switch off or unplug the appliance from the mains supply before
carrying out any maintenance work.
• Clean and/or replace the Filters after the specified time period.
• Clean the hood using a damp cloth and a neutral liquid detergent.
650mm.min.

14GB
CHARACTERISTICS
Dimensions
Components
Ref. Q.ty Product Components
11 Hood Body, complete with: Controls, Light,
Blower, Filters
81 Directional Air Outlet grille
91 Flange ø 150 mm
20 1 Closing element
Ref. Q.ty Installation Components
12a 4 Screws 3,5 x 16
12a 9 Screws 2,9 x 12,7
Q.ty Documentation
1 Instruction Manual
Hood Type 60 90
A 598 898
B 580 880
C 49 200
12e
8
9
1
12a
20
12e

15GB
INSTALLATION
Drilling the Support surface and Fitting the Hood
• The Hood can be fitted directly on the lower
surface of the Wall Units (650 mm min.
above the Cooker Top) using the snap-on
Side Supports.
• Make an opening on the lower surface of the
Wall Unit, as indicated.
• Insert flange 10 into the top exhaust opening.
• Screw the closing profile 20 onto the rear
part of the hood, using the screws 12e (2.9 x
12.7) provided.
• Open the comfort panel by turning the knobs
provided.
• Disconnect the lights connector.
• Disconnect the panel from the hood canopy
by sliding the lever out of the fixing pin,
simultaneously freeing the other end of the
panel from the fixing pin.
• Open the glass panel.
• Remove the metal grease filters one at a time,
by turning the hooks provided.
• Close the glass panel again.
• Insert the Hood until the snap-on side
supports click into place.
• Lock in position by tightening the screws Vf
from underneath the Hood.
• If necessary, adjust the whole filter holder
unit and proceed as follows:
• Loosen the four adjustment screws Vr and
close the glass panel again.
• Move the entire filter holder unit until it
is properly aligned with the wall unit.
• Keeping the hood canopy still, remove the
glass panel and lock the adjustment screws
again.
• The hood can now be fastened to the wall
unit using the four screws 12a (3.5 x 16)
provided.
• Replace the metal grease filters.
• Close the glass panel again and hook up the
comfort panel.
162
503
Vf
Vr
12e