Kallista P25201 User manual

INSTALLATION INSTRUCTIONS
Kitchen Faucet with Remote Valve
1104263_2_A
1 of 7
Questions? Problems? For additional assistance, please contact Kallista’s Customer
Service Department at 1-888-4KALLISTA (1-888-452-5547) or FAX [phone].
P25201

INSTALLATION INSTRUCTIONS
Kitchen Faucet with Remote Valve
1104263_2_A
2 of 7
Questions? Problems? For additional assistance, please contact Kallista’s Customer
Service Department at 1-888-4KALLISTA (1-888-452-5547) or FAX [phone].
THANK YOU FOR CHOOSING KALLISTA
We appreciate your commitment to Kallista quality products. Please take a moment to review this manual
before you install your Kallista product. If you encounter any installation or performance problems, please do
not hesitate to contact us at the phone number listed at the bottom of the page.
BEFORE YOU BEGIN
IMPORTANT! Keep these instructions after installation. They contain servicing and warranty
information.
CAUTION: Risk of fresh water contamination. To prevent water contamination, do not remove any
components from this faucet. This faucet contains back-siphonage protection.
NOTICE: Due to the non-standard 2″ (5.1 cm) diameter of the remote valve, the remote valve cannot be
mounted through a standard 1-3/8″ (3.5 cm) faucet hole of a sink. Instead, choose a sink without faucet holes
then mount the faucet and remote valve through the countertop. Refer to the countertop manufacturer for
proper hole drilling.
Observe all local plumbing and building codes.
Shut off the water supplies.
Inspect waste and supply tubing for damage. Replace if necessary.
Before installation, unpack the faucet and inspect for damage.
For new installations, assemble the faucet to the sink before installing the sink.
Kallista reserves the right to make revisions in the design of faucets without notice, as specied in the Price 
Book.
INSTALLATION
NOTE:1. Locate the remote valve within 8” (20.3
cm) of the spout. Refer to the countertop
manufacturer for proper hole drilling.
1-3/8” (3.5 cm) D. Max
2-1/16” (5.2 cm) D.
8” (20.3 cm) Max
Spout Hole
Valve Hole
Remove the diverter housing.2.
NOTE: DO NOT remove the
plug for the optional
sidespray.
Diverter Housing
Plug
Press to remove.

INSTALLATION INSTRUCTIONS
Kitchen Faucet with Remote Valve
1104263_2_A
3 of 7
Questions? Problems? For additional assistance, please contact Kallista’s Customer
Service Department at 1-888-4KALLISTA (1-888-452-5547) or FAX [phone].
Apply plumbers putty to underside of escutcheon.3.
Escutcheon
Insert the faucet through the surface material.4.
Partially thread screws into the5.
ring.
Slide the ber and metal washers onto the faucet shank. Thread 6.
the ring leaving approximately 1/4” (6 mm) between the ring and the
surface material.
Fiber Washer
Metal Washer
Ring
Ring
1/4”
(6 mm)
Surface Material
INSTALLATION

INSTALLATION INSTRUCTIONS
Kitchen Faucet with Remote Valve
1104263_2_A
4 of 7
Questions? Problems? For additional assistance, please contact Kallista’s Customer
Service Department at 1-888-4KALLISTA (1-888-452-5547) or FAX [phone].
Turn the ring until the screws are to the front and7.
back. Tighten the screws securely and evenly.
Re-install the diverter housing.8.
NOTE: DO NOT remove the plug for the optional
sidespray.
Diverter Housing
Plug
Press to re-install.
INSTALLATION

INSTALLATION INSTRUCTIONS
Kitchen Faucet with Remote Valve
1104263_2_A
5 of 7
Questions? Problems? For additional assistance, please contact Kallista’s Customer
Service Department at 1-888-4KALLISTA (1-888-452-5547) or FAX [phone].
9.
Apply plumbers putty to underside ofa.
remote valve.
Insert the remote valve through theb.
surface material.
Remote Valve
Position the remote valve with the cold water supply on10.
the left AND the spout connection toward the front of the
sink.
NOTE: When the lever is pulled toward the front of the
sink, the red and blue markings on the escutcheon will
be revealed.
Cold Water
Supply Tag
Cold
Hot
On
Partially thread screws into11.
the ring.
Slide the washer onto the remote valve shank. Thread the ring12.
leaving approximately 1/4” (6 mm) between the ring and the
surface material.
Washer
Ring
Surface Material
1/4”
(6 mm)
Ring
INSTALLATION

INSTALLATION INSTRUCTIONS
Kitchen Faucet with Remote Valve
1104263_2_A
6 of 7
Questions? Problems? For additional assistance, please contact Kallista’s Customer
Service Department at 1-888-4KALLISTA (1-888-452-5547) or FAX [phone].
Turn the ring until the screws are to13.
the front and back. Tighten the screws
securely and evenly.
Connect the hose from the remote valve to the diverter14.
housing.
Diverter Housing
(From Spout)
From Remote
Valve
Press to
insert hose.
Connect and tighten the supply hoses.15.
NOTE: If the sink installation requires that you coil the supply
hoses, maintain a 3” (7.6 cm) diameter minimum inside coil.
Cold
Hot
3" (7.6 cm) D. Minimum
Check for leaks.16.
INSTALLATION

INSTALLATION INSTRUCTIONS
Kitchen Faucet with Remote Valve
1104263_2_A
7 of 7
Questions? Problems? For additional assistance, please contact Kallista’s Customer
Service Department at 1-888-4KALLISTA (1-888-452-5547) or FAX [phone].
Remove the aerator.17.
Key
Flush the lines.18. Reinstall the aerator.19.
NOTE: Retain the key for
future use. Clips on the sides
of the key may be used to
clip to supply hoses.
Key
If using optional sidespray (purchased separately), remove plug from diverter and install sidespray20.
according to manufacturer’s instructions.
Diverter Housing
(From Spout)
Plug
Diverter Housing
(From Spout)
From Optional Sidespray
(Purchased Separately)
Press to
release plug.
Press to
insert hose.
INSTALLATION