Kallista P24410-CR User manual

INSTALLATION INSTRUCTIONS
Wall-Mounted Basin Set
1072016_2_C
1 of 6
Questions? Problems? For additional assistance, please contact KALLISTA’s Customer
Service Department at 1-888-4KALLISTA (1-888-452-5547) or FAX [phone].
P24410-CR
P24411-CR
P24410-LV
P24411-LV

INSTALLATION INSTRUCTIONS
Wall-Mounted Basin Set
1072016_2_C
2 of 6
Questions? Problems? For additional assistance, please contact KALLISTA’s Customer
Service Department at 1-888-4KALLISTA (1-888-452-5547) or FAX [phone].
THANK YOU FOR CHOOSING KALLISTA
We appreciate your commitment to KALLISTA quality products. Please take a moment to review this manual
before you install your KALLISTA product. If you encounter any installation or performance problems, please do
not hesitate to contact us at the phone number listed at the bottom of the page.
TOOLS
Hex
Wrench
Phillips
Screwdriver
IMPORTANT INFORMATION
Shut off the main water supply.
Observe all local plumbing and building codes.
If needed, complete the nished wall before beginning this installation.
KALLISTA reserves the right to make revisions in the design of products without notice, as specied in the
Price Book.

INSTALLATION INSTRUCTIONS
Wall-Mounted Basin Set
1072016_2_C
3 of 6
Questions? Problems? For additional assistance, please contact KALLISTA’s Customer
Service Department at 1-888-4KALLISTA (1-888-452-5547) or FAX [phone].
INSTALLATION
Spout Shank
Screws
Set Screw
Flange
Gasket
Spout Escutcheon
O-Ring
Spout
Faucet Outlet Port
Install the Spout
IMPORTANT! Use care when installing the spout to avoid scratching the nish.
Insert the gasket into the back of the spout escutcheon.
Conrm that the O-ring is inside the escutcheon.
Carefully slide the spout escutcheon onto the spout about halfway.
Thread the spout into the spout shank until it is snug. If needed, adjust the spout slightly to position it so it
points straight down.
Secure the spout in place by mounting the ange to the faucet outlet port with the screws provided.
Carefully slide the spout escutcheon and press rmly against the nished wall.
Secure the spout escutcheon to the spout with the set screw.

INSTALLATION INSTRUCTIONS
Wall-Mounted Basin Set
1072016_2_C
4 of 6
Questions? Problems? For additional assistance, please contact KALLISTA’s Customer
Service Department at 1-888-4KALLISTA (1-888-452-5547) or FAX [phone].
INSTALLATION
Install the Handle Assemblies
Unscrew the escutcheon support from the handle assembly. Remove the two screws connecting the
escutcheon adapter and escutcheon support and separate the parts.
Note: Be sure to retain the wear washer when removing the screws. Replace before installing handle assembly.
With 8-32 x 1-1/2″ at head screws included in the parts bag, turn the screws into
the escutcheon adapter about a 1/4″. Tighten the escutcheon adapter to the valve
body. Do not overtighten or bend the screws. Perform this operation for both hot
and cold valves. Remove screws for next operation.
Slide a spline adapter onto the stem extension.
Place a stem extension on the valve stem. Secure with the screw provided.
Place the escutcheon support onto the escutcheon adapter and line up screw holes. Ensure the gasket is
installed between the nished wall and the escutcheon support. Thread two 8-32 x 7/8″ screws and tighten
until the escutcheon support is ush with the nished wall. If the screws bottom out in the escutcheon
adapter and the escutcheon support is not tight against the nished wall, use the 8-32 x 1/2″ screws.
Thread a handle assembly onto the escutcheon support and move the handle to the closed position (Hot =
Clockwise, Cold = Counterclockwise). Lever handles should be horizontal when closed.
If adjustment is needed to achieve the desired handle alignment, remove the handle assembly, screw and
spline adapter. Turn the spline adapter 1/4 turn. Check the handle position. Repeat the procedure until the
proper handle position is achieved. Secure with the screw.
Re-assemble the handle assembly onto the escutcheon support. To maintain the proper handle alignment,
hold the handle in place with one hand and turn the base of the handle with the other hand.
Repeat the procedures with the second handle.
Escutcheon Adapter
Gasket
Escutcheon Support
Wear Washer
Escutcheon Adapter
Valve Stem
Valve Body
Spline Adapter
Stem Extension Handle Assembly
Escutcheon Adapter
Gasket
Escutcheon Support
Wear Washer
Escutcheon Adapter
Valve Stem
Valve Body
Spline Adapter
Stem Extension Handle Assembly

INSTALLATION INSTRUCTIONS
Wall-Mounted Basin Set
1072016_2_C
5 of 6
Questions? Problems? For additional assistance, please contact KALLISTA’s Customer
Service Department at 1-888-4KALLISTA (1-888-452-5547) or FAX [phone].
INSTALLATION
Install the Drain
Disassemble the stopper and ange from the drain body.
Apply a small bead of putty or sealant to the bottom of the ange.
Insert the ange into the drain opening. Ensure the gasket is inside
the ange.
From the underside of the lavatory thread the drain body onto the
ange assembly. Tighten rmly.
Install the stopper and tighten rmly.
Turn the drain body such that the word KALLISTA on the stopper is
straight. Tighten the drain body nut rmly while holding the drain body
to maintain the stopper position.
Using a damp cloth, remove any excess putty or sealant.
Connect the trap.
Drain Body
Drain Body Nut
Flange
Stopper

INSTALLATION INSTRUCTIONS
Wall-Mounted Basin Set
1072016_2_C
6 of 6
Questions? Problems? For additional assistance, please contact KALLISTA’s Customer
Service Department at 1-888-4KALLISTA (1-888-452-5547) or FAX [phone].
INSTALLATION
Complete the Installation
Connect the tailpiece and P-trap (not supplied).
Ensure that all connections are watertight.
Remove the aerator by turning it counterclockwise. Use the supplied key if required for removal of your
aerator.
Open the drain. Turn on the main water supply and check for leaks. Repair as needed.
Open both hot and cold valves and run water through the spout for one minute to remove debris. Check for
leaks in the exible hose connections. Turn valves off.
Re-install the aerator.
Retain the key for future use.
Spout
Aerator
Spout
Aerator
Key