KAM HEXATRIX GLOW User manual

HEXATRIX GLOW
6 lens multi-beam scanning LED lighting effect
192 x 5mm RGB LEDs
72 x red, 72 x green, 48 x blue LEDs
Full DMX512 operation / 10 DMX channels
Auto mode / Sound-to-Light operation via built-in mic
Variable mic sensitivity / Master/Slave mode
Adjustable metal hanging bracket
Safety chain loop / Mains fused IEC
Dimensions: 410 x 170 x 320mm (WxHxD)
Weight: 2Kg
M A N U A L V E R S I O N 1 . 0
07 / 07 / 11
For the latest instruction manual updates and information on the entire Kam range visit:
www.kam.co.uk
Kam products are manufactured by: Lamba plc, Unit 1, Southfields Road, Dunstable, Bedfordshire, United Kingdom LU6 3EJ
Telephone: (+44) (0)1582 690600 • Fax: (+44) (0)1582 690400 • Email: [email protected] • Web: www.lambaplc.com
If this product is ever no longer functional please take it to a recycling plant for environmentally friendly disposal.
Due to continuous product development, specifications and appearance are subject to change.
© Copyright Lamba plc 2010. E&OE.

Thank you for purchasing this KAM product, we are sure that it will serve you for many years to come.
To optimise the performance of this product, please read these operating instructions carefully to familiarise yourself with the basic
operations of this unit. After you have read the instructions, please retain them for future reference.
This unit has been tested at the factory before being shipped to you.
To prevent or reduce the risk of electrical shock or fire, do not expose the unit to rain or moisture. To prevent a fire hazard, do not
expose the unit to any naked flame sources. Unplug this apparatus during lightning storms or if it is unlikely to be used for long
periods of time.
When installing the unit, please ensure you leave enough space around the unit for ventilation. Slots and openings in the unit are
provided for ventilation to ensure reliable operation of the product and to protect it from overheating. To prevent fire hazard, the
openings should never be blocked or covered.
Always handle the power cable by the plug. Never pull out the plug by pulling on the cable. Never touch the power cable when your
hands are wet as this could cause an electric shock. Do not tie a knot in the cable. The power cable should be placed such that it is
not likely to be stepped on. A damaged power cable can cause a fire or give you an electrical shock. Check
the power cord periodicaly, if you ever find that it is damaged, replace it before using the unit again. Contact your retailer for a
replacement.
The voltage of the available power supply differs according to country or region. Be sure that the power supply voltage of the area
where this unit is to be used meets the required written on the unit.
The lightning flash symbol inside a triangle is intended to alert the user to the presence high voltage within the unit’s
enclosure that may be of sufficient power to constitute a risk of electrical shock to persons.
Caution: to prevent the risk of electric shock, do not attempt to open the unit. No user-serviceable parts inside. Refer all
servicing to qualified service personnel.
The exclamation mark inside a triangle is intended to alert the user to the presence of important operating and
maintenance instructions in the literature accompanying the appliance.
Any modification carried out on the unit may invalidate the unit’s warranty.
If applicable, only use the stand, tripod or bracket specified or sold with the apparatus.
Select the installation location of your unit carefully. Avoid placing it in direct sunlight or locations subject to vibration and excessive
dust. Do not use the unit where there are extremes in temperature (below 41ºF / 5ºC or exceeding 95ºF / 35ºC).
Unpacking and safety: Please unpack your new product carefully, your new product should reach you in perfect condition. Please
check that no damage has occurred during transit. If any damage is found, do not operate your unit. Please contact the retailer you
purchased it from immediately. If there is any damage to the mains cable do not use the device. Always disconnect the unit from
the mains supply when carrying out any servicing or cleaning of the unit.
The serial number for this equipment should be located on the rear or underside of the unit. Please make a note of this number as
you will need it for your warranty, it is a good idea to keep a copy of the serial number for your own records.

Function
DIP
1
DIP
2
DIP
3
DIP
4
DIP
5
DIP
6
DIP
7
DIP
8
DIP
9
DIP
10
DIP
11
DIP
12
Mode
Single LED move from left
to right and up to down
1
0
0
0
0
0
0
0
0
1
X
0
Auto (Master)
Single row LED move from
up to down
0
1
0
0
0
0
0
0
0
1
X
0
Auto (Master)
Single row LED move from
left to right
0
0
1
0
0
0
0
0
0
1
X
0
Auto (Master)
LED move from up to down
and left to right
0
0
0
1
0
0
0
0
0
1
X
0
Auto (Master)
LED flash and move from
up to down and left to right
0
0
0
0
1
0
0
0
0
1
X
0
Auto (Master)
LED1.2.3.4 eye light
bounce-Slow
0
0
0
0
0
0
0
0
0
1
X
0
Auto (Master)
LED1.2.3.4 eye light
bounce-Medium
0
0
0
0
0
0
1
0
0
1
X
0
Auto (Master)
LED1.2.3.4eye light
bounce-Fast
0
0
0
0
0
0
0
1
0
1
X
0
Auto (Master)
Strobe
0
0
0
0
0
0
0
0
1
1
X
0
Auto (Master)
Auto program
0
0
0
0
0
0
0
0
0
0
X
0
Auto (Master)
Sound Control
0
0
0
0
0
0
0
0
0
0
X
1
Sound-control
(Master)
1=ON
0=OFF
X=Function
Auto Mode
In order to select Auto mode, set dipswitches 0 to 12 to the OFF position．
Sound Control
In order to select Sound Controlled Mode, set dipswitch 12 to the ON position and dipswitches 1 to 11 to the OFF position.
Master/Slave
To set the first unit to master, select the desired function mode using the dipswitch guide above (example, set the dipswitch 12 on
for sound controlled mode). Using a 3 pin XLR/DMX cable, connect from the DMX output on the first unit (master) to the second
unit’s (slave) DMX input. Set dipswitch 1 on the second unit (slave) into the on position. All other slave units must be set in the
same way. Only one master unit must be set.

DMX Control
Channel
Value
Function
CH1
0-14
Blackout
15-19
Red
20-24
Green
25-29
Blue
30-34
Red/Green
35-39
Red/Blue
40-44
Green/Blue
45-49
Red/Green/Blue
100-255
Select the automatic program
CH2
Set the DMX value of Channel 1 to more than 50
0-255
Select the automatic program
CH3
0-255
Speed from fast to slow
CH4
Set the DMX value of Channel 1 between 50-99
0-255
Up to down, slow to fast
CH5
Set the DMX value of Channel 1 between 50-99
0-255
Left to right, slow to fast
CH6
Set the DMX value of Channel 1 between 50-99
0-255
Inside to outside, slow to fast
CH7
Set the DMX value of Channel 1 between 50-99
0-255
Up to down, left to right, inside to outside, slow to fast
CH8
0-255
Strobe from Slow to fast
CH9
Set the DMX value of Channel 1 between 15-99
0-14
All bright
15-255
Dimmer
CH10
Set the DMX value of Channel 1 between 15-99
0-127
6 LED lenses illuminated
128-190
4 LED lenses illuminated
191-255
2 LED lenses are not illuminated
Specifications
Power supply
90-250 V AC, 50 Hz ~ 60 Hz ~
Power consumption
20W
Current
0.2A
Sound control
via built-in microphone
DMX-512-connection
3-pin XLR
Dimensions
410 x 170 x 320mm (WxHxD)
Weight
2 kg
Maximum ambient temperature T
45℃
Maximum housing temperature T
50℃
Fuse
F0.5A, 250V
Channel
10
Number of LEDs
5mm x 192pcs